I am getting a bit sentimental as I haven’t written much about cellular data consumption for the last 10+ years. At the time, it did not take long for most folks in and out of our industry to realize that data traffic and, thereby, so many believed, the total cost of providing the cellular data would be growing far beyond the associated data revenues, e.g., remember the famous scissor chart back in the early two thousand tens. Many believed (then) that cellular data growth would be the undoing of the cellular industry. In 2011 many believed that the Industry only had a few more years before the total cost of providing cellular data would exceed the revenue rendering cellular data unprofitable. Ten years after, our industry remains alive and kicking (though they might not want to admit it too loudly).
Much of the past fear was due to not completely understanding the technology drivers, e.g., bits per second is a driver, and bytes that price plans were structured around not so much. The initial huge growth rates of data consumption that were observed did not make the unease smaller, i.e., often forgetting that a bit more can be represented as a huge growth rate when you start with almost nothing. Moreover, we also did have big scaling challenges with 3G data delivery. It became quickly clear that 3G was not what it had been hyped to be by the industry.
And … despite the historical evidence to the contrary, there are still to this day many industry insiders that believe that a Byte lost or gained is directly related to a loss or gain in revenue in a linear fashion. Our brains prefer straight lines and linear thinking, happily ignoring the unpleasantries of the non-linear world around us, often created by ourselves.
Figure 1 illustrates linear or straight-line thinking (left side), preferred by our human brains, contrasting the often non-linear reality (right side). It should be emphasized that horizontal and vertical lines, although linear, are not typically something that instinctively enters the cognitive process of assessing real-world trends.
Of course, if the non-linear price plans for cellular data were as depicted above in Figure 1, such insiders would be right even if anchored in linear thinking (i.e., even in the non-linear example to the right, an increase in consumption (GBs) leads to an increase in revenue). However, when it comes to cellular data price plans, the price vs. consumption is much more “beastly,” as shown below (in Figure 2);
Figure 2 illustrates the two most common price plan structures in Telcoland; (a, left side) the typical step function price logic that associates a range of data consumption with a price point, i.e., the price is a constant independent of the consumption over the data range. The price level is presented as price versus the maximum allowed consumption. This is by far the most common price plan logic in use. (b, right side) The “unlimited” price plan logic has one price level and allows for unlimited data consumption. T-Mobile US, Swisscom, and SK Telecom have all endorsed the unlimited with good examples of such pricing logic. The interesting fact is that most of those operators have several levels of unlimited tied to the consumptive behavior where above a given limit, the customer may be throttled (i.e., the speed will be reduced compared to before reaching the limit), or (and!) the unlimited plan is tied to either radio access technology (e.g., 4G, 4G+5G, 5G) or a given speed (e.g., 50 Mbps, 100 Mbps, 1Gbps, ..).
Most cellular data price plans follow a step function-like pricing logic as shown in Figure 2 (left side), where within each level, the price is constant up to the nominal data consumption value (i.e., purple dot) of the given plan, irrespective of the consumption. The most extreme version of this logic is the unlimited price plan, where the price level is independent of the volumetric data consumption. Although, “funny” enough, many operators have designed unlimited price plans that, in one way or another, depend on the customers’ consumption, e.g., after a certain level of unlimited consumption (e.g., 200 GB), cellular speed is throttled substantially (at least if the cell under which the customer demand resources are congested). So the “logic” is that if you wanted true unlimited, you still need to pay more than if you only require “unlimited”. Note that for the mathematically inclined, the step function is regarded as (piece-wise) linear … Although our linear brains might not appreciate that finesse very much. Maybe a heuristic that “The brain thinks in straight lines” would be more precisely restated as “The brain thinks in continuous non-constant monotonous straight lines”.
Any increase in consumption within a given pricing-consumption level will not result in any additional revenue. Most price plans allow for considerable growth without incurring additional associated revenues.
NETHERLANDS vs INDONESIA – BRIEFLY.
I like to keep informed and updated about markets I have worked in, with operators I have worked for, and with. I have worked across the globe in many very diverse markets and with operators in vastly different business cycles gives an interesting perspective on our industry. Throughout my career, I have been super interested in the difference between Telco operations and strategies in so-called mature markets versus what today may be much more of a misnomer than 10+ years ago, emerging markets.
The average cellular, without WiFi, consumption per customer in Indonesia was ca. 8 GB per month in 2022. That consumption would cost around 50 thousand Rp (ca. 3 euros) per month. For comparison, in The Netherlands, that consumption profile would cost a consumer around 16 euros per month. As of May 2023, the median cellular download speed was 106 Mbps (i.e., helped by countrywide 5G deployment, for 4G only, the speed would be around 60 to 80 Mbps) compared with 22 Mbps in Indonesia (i.e., where 5G has just been launched. Interestingly, although most likely coincidental, in Indonesia, a cellular data customer would pay ca. 5 times less than in the Netherlands for the same volumetric consumption. Note that for 2023, the average annual income in Indonesia is about one-quarter of that in the Netherlands. However, the Indonesian cellular consumer would also have one-fifth of the quality measured by downlink speed from the cellular base station to the consumer’s smartphone.
Let’s go deeper into how effective consumptive growth of cellular data is monetized… what may impact the consumptive growth, positively and negatively, and how it relates to the telco’s topline.
CELLULAR BUSINESS DYNAMICS.
Figure 3 Between 2016 and 2021, Western European Telcos lost almost 7% of their total cellular turnover (ca. 7+ billion euros over the markets I follow). This corresponds to a total revenue loss of ca. 1.4% per year over the period. To no surprise, the loss of cellular voice-based revenue has been truly horrendous, with an annual loss ca. 30%, although the Covid year (2021 and 2022, for that matter) was good to voice revenues (as we found ourselves confined to our homes and a call away from our colleagues). On the positive side, cellular data-based revenues have “positively” contributed to the revenue in Western Europe over the period (we don’t really know the counterfactual), with an annual growth of ca. 4%. Since 2016 cellular data revenues have exceeded that of cellular voice revenues and are 2022 expected to be around 70% of the total cellular revenue (for Western Europe). Cellular revenues have been and remain under pressure, even with a positive contribution from cellular data. The growth of cellular data volume (not including the contribution generated from WiFi usage) has continued to grow with a 38% annualized growth rate and is today (i.e., 2023) more than five times that of 2016. The annual growth rate of cellular data consumption per customer is somewhat lower ranging from the mid-twenties to the end-thirties percent. Needless to say that the corresponding cellular ARPU has not experienced anywhere near similar growth. In fact, cellular ARPU has generally been lowered over the period.
Some, in my opinion, obvious observations that are worth making on cellular data (I come to realize that although I find these obvious, I am often confronted with a lack of awareness or understanding of those);
Cellular data consumption grows much (much) faster than the corresponding data revenue (i.e., 38% vs 4% for Western Europe).
The unit growth of cellular data consumption does not lead to the same unit growth in the corresponding cellular data revenues.
Within most finite cellular data plans (thus the not unlimited ones), substantial data growth potential can be realized without resulting in a net increase of data-related revenues. This is, of course, trivial for unlimited plans.
The anticipated death of the cellular industry back in the twenty-tens was an exaggeration. The Industry’s death by signaling, voluptuous & unconstrained volumes of demanded data, and ever-decreasing euros per Bytes remains a fading memory and, of course, in PowerPoints of that time (I have provided some of my own from that period below). A good scare does wonders to stimulate innovation to avoid “Armageddon.” The telecom industry remains alive and well.
Figure 4 The latest data (up to 2022) from OECD on mobile data consumption dynamics. Source data can be found at OECD Data Explorer. The data illustrates the slowdown in cellular data growth from a customer perspective and in terms of total generated mobile data. Looking over the period, the 5-year cumulative growth rate between 2016 and 2021 is higher than 2017 to 2022 as well as the growth rate between 2022 and 2021 was, in general, even lower. This indicates a general slowdown in mobile data consumption as 4G consumption (in Western Europe) saturates and 5G consumption still picks up. Although this is not an account of the observed growth dynamics over the years, given the data for 2022 was just released, I felt it was worth including these for completeness. Unfortunately, I have not yet acquired the cellular revenue structure (e.g., voice and data) for 2022, it is work in progress.
WHAT DRIVES CONSUMPTIVE DATA GROWTH … POSITIVE & NEGATIVE.
What drives the consumer’s cellular data consumption? As I have done with my team for many years, a cellular operator with data analytics capabilities can easily check the list of positive and negative contributors driving cellular data consumption below.
Positive Growth Contributors:
Customer or adopter uptake. That is, new or old, customers that go from non-data to data customers (i.e., adopting cellular data).
Increased data consumption (i.e., usage per adopter) within the cellular data customer base that is driven by a lot of the enablers below;
Affordable pricing and suitable price plans.
More capable Radio Access Technology (RAT), e.g., HSDPA → HSPA+ → LTE → 5G, effectively higher spectral efficiency from advanced antenna systems. Typically will drive up the per-customer data consumption to the extent that pricing is not a barrier to usage.
More available cellular frequency spectrum is provisioned on the best RAT (regarding spectral efficiency).
Good enough cellular network consistent with customer demand.
Affordable and capable device ecosystem.
Faster mobile device CPU leads to higher consumption.
Faster & more capable mobile GPUs lead to higher consumption.
Device screen size. The larger the screen, the higher the consumption.
Access to popular content and social media.
Figure 5 illustrates the description of data growth as depending on the uptake of Adopters and the associated growth rate α(t) multiplied by the Usage per Adopter and the associated growth rate of usage μ(t). The growth of the Adopters can typically be approximated by an S-curve reaching its maximum as there are few more customers left to adopt a new service or product or RAT (i.e., α(t)→0%). As described in this section, the growth of usage per adopter, μ(t), will depend on many factors. Our intuition of μ is that it is positive for cellular data and historically has exceeded 30%. A negative μ would be an indication of consumptive churn. It should not be surprising that overall cellular data consumption growth can be very large as the Adopter growth rate is at its peak (i.e., around the S-curve inflection point), and Usage growth is high as well. It also should not be too surprising that after Adopter uptake has reached the inflection point, the overall growth will slow down and eventually be driven by the Usage per Adopter growth rate.
Figure 6 Using the OECD data (OECD Data Explorer) for the Western European mobile data per customer consumptive growth from 2011 to 2022, the above illustrates the annual growth rate of per-customer data mobile consumption. Mobile data consumption is a blend of usage across the various RATs enabling packet data usage. There is a clear increased annual growth after introducing LTE (4G) followed by a slowdown in annual growth, possibly due to reaching saturation in 4G adaptation, i.e., α3G→4G(t) → 0% leaving μ4G(t) driving the cellular data growth. There is a relatively weak increase in 2021, and although the timing coincides with 5G non-standalone (NSA) introduction (typically at 700 MHz or dynamics spectrum share (DSS) with 4G, e.g., Vodafone-Ziggo NL using their 1800 MHz for 4G and 5G) the increase in 2020 may be better attributed to Covid lockdown than a spurt in data consumption due to 5G NSA intro.
Anything that creates more capacity and quality (e.g., increased spectral efficiency, more spectrum, new, more capable RAT, better antennas, …) will, in general, result in an increased usage overall as well as on a per-customer basis (remember most price plans allow for substantial growth within the plans data-volume limit without incurring more cost for the customer). If one takes the above counterfactual, it should not be surprising that this would result in slower or negative consumption growth.
Negative growth contributors:
Cellular congestion causes increased packet loss, retransmissions, and deteriorating latency and speed performance. All in all, congestion may have a substantial negative impact on the customer’s service experience.
Throttling policies will always lower consumption and usage in general, as quality is intentionally lowered by the Telco.
Increased share of QUIC content on the network. The QUIC protocol is used by many streaming video providers (e.g., Youtube, Facebook, TikTok, …). The protocol improves performance (e.g., speed, latency, packet delivery, network changes, …) and security. Services using QUIC will “bully” other applications that use TCP/IP, encouraging TCP/IP to back off from using bandwidth. In this respect, QUIC is not a fair protocol.
Elephant flow dynamics (e.g., few traffic flows causing cell congestion and service degradation for the many). In general, elephant flows, particularly QUIC based, will cause an increase in TCP/IP data packet retransmissions and timing penalties. It is very much a situation where a few traffic flows cause significant service degradation for many customers.
One of the manifestations of cell congestion is packet loss and packet retransmission. Packet loss due to congestion ranges from 1% to 5%. or even several times higher at moments of peak traffic or if the user is in a poor cellular coverage area. The higher the packet loss, the worse the congestion, and the worse the customer experience. The underlying IP protocols will attempt to recover a lost packet by retransmission. The retransmission rate can easily exceed 10% to 15% in case of congestion. Generally, for a reliable and well-operated network, the packet loss should be well below 1% and even as low as 0.1%. Likewise, one would expect a packet retransmission rate of less than 2% (I believe the target should be less than 1%).
Thus, customers that happen to be under a given congested cell (e.g., caused by an elephant flow) would incur a substantially higher rate of retransmitted data packages (i.e., 10% to 15% or higher) as the TCP/IP protocol tries to make up for lost data packages. The customer may experience substantial service quality degradation and, as a final (unintended) “insult”, often be charged for those additional retransmitted data volumes.
From a cellular perspective, as the congestion has been relieved, the cellular operator may observe that the volume on the congested cell actually drops. The reason is that the packet loss and retransmission drops to a level far below the congested one (e.g., typically below 1%). As the quality improves for all customers demanding service from the previously overloaded (i.e., congested) cell, sustainable volume growth will commence in total and as well as will the average consumption on a customer basis. As will be shown below for normal cellular data consumption and most (if not all) price plans, a few percentage points drop in data volume will not have any meaningful effect on revenues. Either because the (temporary) drop happens within the boundaries of a given price plan level and thus has no effect on revenue, or because the overall gainful consumptive growth, as opposed to data volume attributed to poor quality, far exceeds the volume loss due to improved capacity and quality of a congested cell.
Well-balanced and available cellular sites will experience positive and sustainable data traffic growth.
Congested and over-loaded cellular sites will experience a negative and persistent reduction of data traffic.
Actively managing the few elephant flows and their negative impact on the many will increasecustomer satisfaction, reduce consumptive churn, and increase data growth, easily compensating for the congestion-induced increases due to packet retransmission. And unless an operator consistently is starved for radio access investments, or has poor radio access capacity management processes, most cell congestion can be attributed to the so-called elephant flows.
CELLULAR DATA CONSUMPTION IN REAL NETWORKS – ON A SECTOR LEVEL.
And irrespective of whatever drives positive and negative growth, it is worth remembering that daily traffic variations on a sector-by-sector basis and an overall cellular network level are entirely natural. An illustration of such natural sector variation over a (non-holiday) week is shown below in Figure 7 (c) for a sector in the top-20% of busiest sectors. In this example, the median variation over all sectors in the same week, as shown below, was around 10%. I often observe that even telco people (that should know better) find this natural variation quite worrisome as it appears counterintuitive to their linear growth expectations. Proper statistical measurement & analysis methodologies must be in place if inferences and solid analysis are required on a sector (or cell) basis over a relatively short time period (e.g., day, days, week, weeks,…).
Figure 7 illustrates the cellular data consumption daily variation over a (non-holiday) week. In the above, there are three examples (a) a sector from the bottom 20% in terms of carried volume, (b) a sector with a median data volume, and (c) a sector taken from the top 20% of carried data volume. Over the three different sectors (low, median, high) we observe very different variations over weekdays. From the top-20%, we have an almost 30% variation between the weekly minimum (Tuesday) and the weekly maximum (Thursday) to the bottom-20% with a variation in excess of 200% over the week. The charts above show another trend we observe in cellular networks regarding consumptive variations over time. Busy sectors tend to have a lower weekly variation than less busy sectors. I should point out that I have made no effort to select particular sectors. I could easily find some (of the less busy sectors) with even more wild variations than shown above.
The day-to-day variation is naturally occurring based on the dynamic behavior of the customers served by a given sector or cell (in a sector). I am frequently confronted with technology colleagues (whom I respect for their deep technical knowledge) that appear to expect (data) traffic on all levels monotonously increase with a daily growth rate that amounts to the annual CAGR observed by comparing the end-of-period volume level with the beginning of period volume level. Most have not bothered to look at actual network data and do not understand (or, to put it more nicely, simply ignore) the naturally statistical behavior of traffic that drives hourly, daily, weekly, and monthly variations. If you let statistical variations that you have no control over drive your planning & optimization decisions. In that case, you will likely fail to decide on the business-critical ones you can control.
An example of a high-traffic (top-20%) sector’s complete 365 day variations of data consumption is shown below in Figure 8. We observe that the average consumption (or traffic demand) increases nicely over the year with a bit of a slowdown (in this European example) during the summer vacation season (same around official holidays in general). Seasonal variations is naturally occurring and often will result in a lower-than-usual daily growth rate and a change in daily variations. In the sector traffic example below, Tuesdays and Saturdays are (typically) lower than the average, and Thursdays are higher than average. The annual growth is positive despite the consumptive lows over the year, which would typically freak out my previously mentioned industry colleagues. Of course, every site, sector, and cell will have a different yearly growth rate, most likely close to a normal distribution around the gross annual growth rate.
Figure 8 illustrates a top-20% sector’s data traffic growth dynamics (in GB) over a calendar year’s 365 days. Tuesdays and Saturdays are likely below the weekly average data consumption, and Thursdays are more likely to be above. Furthermore, the daily traffic growth is slowing around national holidays and in the summer vacation (i.e., July & August for this particular Western European country).
And to nail down the message. As shown in the example in Figure 9 below, every sector in your cellular network from one time period to the other will have a different positive and negative growth rate. The net effect over time (in terms of months more than days or weeks) is positive as long as customers adopt the supplied RAT (i.e., if customers are migrating from 4G to 5G, it may very well be that 4G consumed data will decline while the 5G consumed data will increase) and of course, as long as the provided quality is consistent with the expected and demanded quality, i.e., sectors with congestion, particular so-called elephant-flow induced congestion, will hurt the quality of the many that may reduce their consumptive behavior and eventually churn.
Figure 9 illustrates the variation in growth rates across 15+ thousand sectors in a cellular network comparing the demanded data volume between two consecutive Mondays per sector. Statistical analysis of the above data shows that the overall average value is ca. 0.49% and slightly skewed towards the positive growths rates (e.g., if you would compare a Monday with a Tuesday, the histogram would typically be skewed towards the negative side of the growth rates as Tuesday are a lower traffic day compared to Monday). Also, with the danger of pointing out the obvious, the daily or weekly growth rates expected from an annual growth rate of, for example, 30% are relatively minute, with ca. 0.07% and 0.49%, respectively.
The examples above (Figures 7, 8, and 9) are from a year in the past when Verstappen had yet to win his first F1 championship. That particular weekend also did not show F1 (or Sunday would have looked very different … i.e., much higher) or any other big sports event.
CELLULAR DATA PRICE PLAN LOGIC.
Figure 10 above is an example of the structure of a price plan. Possibly represented slightly differently from how your marketeer would do (and I am at peace with that). We observe the illustration of a price level of 8 data volume intervals on the upper left chart. This we can also write as (following the terminology of the lower right corner);
Thus, for the package allowing the customer to consume up to 3 GB is priced at 20 (irrespective of whether the customer would consume less). For package a consumer would pay 100 for a data consumption allowance up to 35 GB. Of course, we assume that the consumer choosing this package would generally consume more than 24 GB, which is the next cheaper package (i.e., ).
The price plan example above clearly shows that each price level offers customers room to grow before upgrading to the next level. For example, a customer consuming no more than 8 GB per month, fitting into , could increase consumption with 4 GB (+50%) before considering the next level price plan (i.e., ). This is just to illustrate that even if the customer’s consumption may grow substantially, one should not per se be expecting more revenue.
Even though it should be reasonably straightforward that substantial growth of a customer base data consumption cannot be expected to lead to an equivalent growth in revenue, many telco insiders instinctively believe this should be the case. I believe that the error may be due to many mentally linearizing the step-function price plans (see Figure 2 upper right side) and simply (but erroneously) believing that any increase (decrease) in consumption directly results in an increase (or decrease) in revenue.
DATA PRICING LOGIC & USAGE DISTRIBUTION.
If we want to understand how consumptive behavior impacts cellular operators’ toplines, we need to know how the actual consumption distributes across the pricing logic. As a high-level illustration, Figure 11 (below) shows the data price step-function logic from Figure 9 with an overall consumptive distribution superimposed (orange solid line). It should be appreciated that while this provides a fairly clear way of associating consumption with pricing, it is an oversimplification at best. It will nevertheless allow me to estimate crudely the number of customers that are likely to have chosen a particular price plan matching their demand (and affordability). In reality, we will have customers that have chosen a given price plan but either consume less than the limit of the next cheaper plan (thus, if consistently so, could save but go to that plan). We will also have customers that consume more than their allowed limit. Usually, this would result in the operator throttling the speed and sending a message to the customer that the consumption exceeds the limit of the chosen price plan. If a customer would consistently overshoots the limits (with a given margin) of the chosen plan, it is likely that eventually, the customer will upgrade to the next more expensive plan with a higher data allowance.
Figure 11 above illustrates on the left side a consumptive distribution (orange line) identified by its mean and standard deviation superimposed on our price plan step-function logic example. The right summarizes the consumptive distribution across the eight price plan levels. Note that there is a 9th level in case the 200 GB limit is breached (0.2% in this example). I am assuming that such customers pay twice the price for the 200 GB price plan (i.e., 320).
In the example of an operator with 100 million cellular customers, the consumptive distribution and the given price plan lead to a fiat of 7+ billion per month. However, with a consumptive growth rate of 30% to 40% annually per active cellular data user (on average), what kind of growth should we expect from the associated cellular data revenues?
Figure 12 In the above illustration, I have mapped the consumptive distribution to the price plan levels and then developed the begin-of-period consumptive distribution (i.e., the light green curve) month by month until month 12 has been reached (i.e., the yellow curve). I assume the average monthly consumptive cellular data growth is 2.5% or ca. 35% after 12 months. Furthermore, I assume that for the few customers falling outside the 200 GB limit that they will purchase another 200 GB plan. For completeness, the previous 12 months (previous year) need to be carried out to compare the total cumulated cellular data revenue between the current and previous periods.
Within the current period (shown in Figure 12 above), the monthly cellular data revenue CAGR comes out at 0.6% or a total growth of 7.4% of monthly revenue between the beginning period and the end period. Over the same period, the average data consumption (per user) grew by ca. 34.5%. In terms of the current year’s total data revenue to the previous year’s total data revenue, we get an annual growth rate of 8.3%. This illustrates that it should not be surprising that the revenue growth can be far smaller than the consumptive growth given price plans such as the above.
It should be pointed out that the above illustration of consumptive and revenue growth simplifies the growth dynamics. For example, the simulation ignores seasonal swings over a 12-month period. Also, it attributes 1-to-1 all consumption falling within the price range to that particular price level when there is always spillover on both upper and lower levels of a price range that will not incur higher or lower revenues. Moreover, while mapping the consumptive distribution to the price-plan giga-byte intervals makes the simulation faster (and setup certainly easier), it is also not a very accurate approach to the coarseness of the intervals.
A LEVEL DEEPER.
While working with just one consumptive distribution, as in Figure 11 and Figure 12 above, allows for simpler considerations, it does not fully reflect the reality that every price plan level will have its own consumptive distribution. So let us go that level deeper and see whether it makes a difference.
Figure 13 above, illustrates the consumptive distribution within a given price plan range, e.g., the “5 GB @ 30” price-plan level for customers with a consumption higher than 3 GB and less than or equal to 5 GB. It should come as no surprise that some customers may not reach even the 3 GB, even though they pay for (up to) 5 GB, and some may occasionally exceed the 5 GB limit. In the example above, 10% of customers have a consumption below 3 GB (and could have chosen the next cheaper plan of up to 3 GB), and 3% exceed the limits of the chosen plan (an event that may result in the usage speed being throttled). As the average usage within a given price plan level approaches the ceiling (e.g., 5 GB in the above illustration), in general, the standard deviation will reduce accordingly as customers will jump to the Next Expensive Plan to meet their consumptive needs (e.g., “12 GB @ 50” level in the illustration above).
Figure 14 generalizes Figure 11 to the full price plan and, as illustrated in Figure 12, let the consumption profiles develop in time over a 12-month period (Initial and +12 month shown in the above illustration). The difference between the initial and 12 months can be best appreciated with the four smaller figures that break up the price plan levels in 0 to 40 GB and 40 to 200 GB.
The result in terms of cellular data revenue growth is comparable to that of the higher-level approach of Figure 12 (ca. 8% annual revenue growth vs 34 % overall consumptive annual growth rate). The detailed approach of Figure 11 is, however, more complicated to get working and requires much more real data to work with (which obviously should be available to operators in this time and age). One should note that in the illustrated example price plan (used in the figures above) that at a 2.5% monthly consumptive growth rate (i.e., 34% annually), it would take a customer an average of 24 months (spread of 14 to 35 month depending on level) to traverse a price plan level from the beginning of the level (e.g., 5 GB) to the end of the level (12 GB). It should also be clear that as a customer enters the highest price plan levels (e.g., 100 GB and 200 GB), little additional can be expected to be earned on those customers over their consumptive lifetime.
The illustrated detailed approach shown above is, in particular, useful to test a given price plan’s profitability and growth potential, given the particularities of the customers’ consumptive growth dynamics.
The additional finesse that could be considered in the analysis could be an affordability approach because the growth within a given price level slows down as the average consumption approaches the limit of the given price level. This could be considered by slowing the mean growth rate and allowing for the variance to narrow as the density function approaches the limit. In my simpler approach, the consumptive distributions will continue to grow at a constant growth rate. In particular, one should consider more sophisticated approaches to modeling the variance that determines the spillover into less and more expensive levels. An operator should note that consumption that reduces or consistently falls into the less expensive level expresses consumptive churn. This should be monitored on a customer level as well as on a radio access cell level. Consumptive churn often reflects the supplied radio access quality is out of sync with the customer demand dynamics and expectations. On a radio access cell level, the diligent operator will observe a sharp increase in retransmitted data packages and increased latency on a flow (and active customer basis) hallmarks of a congested cell.
To this day, 20+ odd years after the first packet data cellular price plans were introduced, I still have meetings with industry colleagues where they state that they cannot implement quality-enhancing technologies for the fear that data consumption may reduce and by that their revenues. Funny enough, often the fear is that by improving the quality for typically many of their customers being penalized by a few customers’ usage patterns (e.g., the elephants in the data pipe), the data packet loss and TCP/IP retransmissions are reducing as the quality is improving and more customers are getting the service they have paid for. It is ignoring the commonly established fact of our industry that improving the customer experience leads to sustainable growth in consumption that consequently may also have a positive topline impact.
I am often in situations where I am surprised with how little understanding and feeling Telco employees have for their own price plans, consumptive behavior, and the impact these have on their company’s performance. This may be due to the fairly complex price plans telcos are inventing, and our brain’s propensity for linear thinking certainly doesn’t make it easier. It may also be because Telcos rarely spend any effort educating their employees about their price plans and products (after all, employees often get all the goodies for “free”, so why bother?). Do a simple test at your next town hall meeting and ask your CXOs about your company’s price plans and their effectiveness in monetizing consumption.
So what to look out for?
Many in our industry have an inflated idea (to a fault) about how effective consumptive growth is being monetized within their company’s price plans.
Most of today’s cellular data plans can accommodate substantial growth without leading to equivalent associated data revenue growth.
The apparent disconnect between the growth rate of cellular data consumption (CAGR ~30+%), in its totality as well on an average per-customer basis, and cellular data revenues growth rate (CAGR < 10%) is simply due to the industry’s price plan structures allowing for substantial growth without a proportion revenue growth.
I greatly acknowledge my wife, Eva Varadi, for her support, patience, and understanding during the creative process of writing this Blog.
Tellabs “End of Profit” study executive summary (wordpress.com), (2011). This study very much echoed the increasing Industry concern back in 2010-2012 that cellular data growth would become unprofitable and the industry’s undoing. The basic premise was that the explosive growth of cellular data and, thus, the total cost of maintaining the demand would lead to a situation where the total cost per GB would exceed the revenue per GB within the next couple of years. This btw. was also a trigger point for many cellular-focused telcos to re-think their strategies towards the integrated telco having internal access to fixed and mobile broadband.
B. de Langhe et al., “Linear Thinking in a Nonlinear World”, Harvard Business Review, (May-June, 2017). It is a very nice and compelling article about how difficult it is to get around linear thinking in a non-linear world. Our brains prefer straight lines and linear patterns and dependencies. However, this may lead to rather amazing mistakes and miscalculations in our clearly nonlinear world.
OECD Data Explorer A great source of telecom data, for example, cellular data usage per customer, and the number of cellular data customers, across many countries. Recently includes 2022 data.
I have used Mobile Data – Europe | Statista Market Forecast to better understand the distribution between cellular voice and data revenues. Most Telcos do not break out their cellular voice and data revenues from their total cellular revenues. Thus, in general, such splits are based on historical information where it was reported, extrapolations, estimates, or more comprehensive models.
K.-C. Lan and J. Heidemann, “A measurement study of correlations of Internet flow characteristic” (February 2006). This seminal paper has inspired many other research works on elephant flows. A flow should be understood as an unidirectional series of IP packets with the same source and destination addresses, port numbers, and protocol numbers. The authors define elephant flows as flows with a size larger than the mean plus three standard deviations of the sampled data. Though it is important to point out that the definition is less important. Such elephant flows are typically few (less than 20%) but will cause cell congestion by reducing the quality of many requiring a service in such an affected cell.
Opanga Networks is a fascinating and truly innovative company. Using AI, they have developed their solution around the idea of how to manage data traffic flows, reduce congestion, and increase customer quality. Their (N2000) solution addresses particular network situations where a limited number of customer data usage takes up a disproportionate amount of resources within the cellular network (i.e., the problem with elephant flows). Opanga’s solution optimizes those traffic congestion-impacting flows and results in an overall increase in service quality and customer experience. Thus, the beauty of the solution is that the few traffic patterns, causing the cellular congestion, continue without degradation, allowing the many traffic patterns that were impacted by the few to continue at their optimum quality level. Overall, many more customers are happy with their service. The operator avoids an investment of relatively poor return and can either save the capital or channel it into a much higher IRR (internal rate of return) investment. I have seen tangible customer improvements exceeding 30+ percent improvement to congested cells, avoiding substantial RAN Capex and resulting Opex. And the beauty is that it does not involve third-party network vendors and can be up and running within weeks with an investment that is easily paid back within a few months. Opanga’s product pipeline is tailor-made to alleviate telecom’s biggest and thorniest challenges. Their latest product, with the appropriate name Joules, enables substantial radio access network energy savings above and beyond what features the telcos have installed from their Radio Access Network suppliers. Disclosure:I am associated with Opanga as an advisor to their industrial advisory board.
I built my first Telco technology Capex model back in 1999. I had just become responsible for what then was called Fixed Network Engineering with a portfolio of all technology engineering design & planning except for the radio access network but including all transport aspects from access up to Core and out to the external world. I got a bit frustrated that every time an assumption changed (e.g., business/marketing/sales), I needed to involve many people in my organization to revise their Capex demand. People that were supposed to get our greenfield network rolled out to our customers. Thus, I built my first Capex model that would take the critical business assumptions, size my network (including the radio access network), and consistently assign the right Capex amounts to each category. The model allowed for rapid turnaround on revised business assumptions and a highly auditable track of changes, planning drivers, and unit prices. Since then, I have built best-practice Capex (and technology Opex) models for many Deutsche Telekom AGs and Ooredoo Group entities. Moreover, I have been creating numerous network and business assessment and valuation models (with an eye on M&A), focusing on technology drivers behind Capex and Opex for many different types of telco companies (30+) operating in an extensive range of market environments around the world (20+). Creating and auditing techno-economical models, making those operational and of high quality, it has (for me) been essential to be extensively involved operationally in the telecom sector.
PRELUDE TO CAPEX.
Capital investments, or Capital Expenditures, or just Capex for short, make Telcos go around. Capex is the monetary means used by your Telco to acquire, develop, upgrade, modernize, and maintain tangible, as well as, in some instances, intangible, assets and infrastructure. We can find Capex back under “Property, Plants, and Buildings” (or PPB) in a company’s balance sheet or directly in the profit & loss (or income) statement. Typically for an investment to be characterized as a capital expense, it needs to have a useful lifetime of at least 2 years and be a physical or tangible asset.
What about software? A software development asset is, by definition, intangible or non-physical. However, it can, and often is, assigned Capex status, although such an assignment requires a bit more judgment (and auditorial approvals) than for a real physical asset.
The “Modern History of Telecom” (in Europe) is well represented by Figure 1, showing the fixed-mobile total telecom Capex-to-Revenue ratio from 1996 to 2025.
From 1996 to 2012, most of the European Telco Capex-to-Revenue ratio was driven by investment into mobile technology introductions such as 2G (GSM) in 1996 and 3G (UMTS) in 2000 to 2002 as well as initial 4G (LTE) investments. It is clear that investments into fixed infrastructure, particularly modernizing and enhancing, have been down-prioritized only until recently (e.g., up to 2010+) when incumbents felt obliged to commence investing in fiber infrastructure and urgent modernization of incumbents’ fixed infrastructures in general. For a long time, the investment focus in the telecom industry was mobile networks and sweating the fixed infrastructure assets with attractive margins.
Figure 1 illustrates the “Modern History of Telecom” in Europe. It shows the historical development of Western Europe Telecom Capex to Revenue ratio trend from 1996 to 2025. The maximum was about 28% at the time 2G (GSM) was launched and at minimum after the cash crunch after ultra-expensive 3G licenses and the dot.com crash of 2020. In recent years, since 2008, Capex to Revenue has been steadily increasing as 4G was introduced and fiber deployment started picking up after 20210. It should be emphasized that the Capex to Revenue trend is for both Mobile and Fixed. It does not include frequency spectrum investments.
Across this short modern history of telecom, possibly one of the worst industry (and technology) investments have been the investments we did into 3G. In Europe alone, we invested 100+ billion Euro (i.e., not included in the Figure) into 2100 MHz spectrum licenses that were supposed to provide mobile customers “internet-in-their-pockets”. Something that was really only enabled with the introduction of 4G from 2010 onwards.
Also, from 2010 onwards, telecom companies (in Europe) started to invest increasingly in fiber deployment as well as upgrading their ailing fixed transport and switching networks focusing on enabling competitive fixed broadband services. But fiber investments have picked up in a significant way in the overall telecom Capex, and I suspect it will remain so for the foreseeable future.
Figure 2 When we take the European Telco revenue (mobile & fixed) over the period 1996 to 2025, it is clear that the mobile business model quantum leaped revenue from its inception to around 2008. After this, it has been in steady decline, even if improvement has been observed in the fixed part of the telco business due to the transition from voice-dominated to broadband. Source:https://stats.oecd.org/
As can be observed from Figure 1, since the telecom credit crunch between 2000 and 2003, the Capex share of revenue has steadily increased from just around 12% in 2004, right after the credit crunch, to almost 20% in 2021. Over the period from 2008 to 2021, the industry’s total revenue has steadily declined, as can be seen in Figure 2. Taking the last 10 years (2011-2021) of mobile and fixed revenue data has, on average, reduced by 4+ billion euros a year. The cumulative annual growth rate (CAGR) was at a great +6% from the inception of 2G services in 1996 to 2008, the year of the “great recession.” From 2008 until 2021, the CAGR has been almost -2% in annual revenue loss for Western Europe.
What does that mean for the absolute total Capex spend over the same period? Figure 3 provides the trend of mobile and fixed Capex spending over the period. Since the “happy days” of 2G and 3G Capex spending, Capex rapidly declined after the industry spent 100+ billion Euro on 3G spectrum alone (i.e., 800+ million euros per MHz or 4+ euros per MHz-pop) before the required multi-billion Euro in 3G infrastructure. Though, after 2009, which was the lowest Capex spend after the 3G licenses were acquired, the telecom industry has steadily grown its annual total Capex spend with ca. +1 billion Euro per year (up to 2021) financing new technology introductions (4G and 5G), substantial mobile radio and core modernizations (a big refresh ca. every 6 -7 years), increasing capacity to continuously cope with consumer demand for broadband, fixed transport, and core infrastructure modernization, and last but not least (since the last ~ 8 years) increasing focus on fiber deployment. Over the same period from 2009 to 2021, the total revenue has declined by ca. 5 billion euros per year in Western Europe.
Figure 3 Using the above “Total Capex to Revenue” (Figure 1) and “Total Revenue” (Figure 2) allows us to estimate the absolute “Total Capex” over the same period. Apart from the big Capex swing around the introduction of 2G and 3G and the sharp drop during the “credit crunch” (2000 – 2003), Capex has grown steadily whilst the industry revenue has declined.
It will be very interesting to see how the next 10 years will develop for the telecom industry and its capital investment. There is still a lot to be done on 5G deployment. In fact, many Telcos are just getting started with what they would characterize as “real 5G”, which is 5G standalone at mid-band frequencies (e.g., > 3 GHz for Europe, 2.5 GHz for the USA), modernizing antenna structures from standard passive (low-order) to active antenna systems with higher-order MiMo antennas, possible mmWave deployments, and of course, quantum leap fiber deployment in laggard countries in Europe (e.g., Germany, UK, Greece, Netherlands, … ). Around 2028 to 2030, it would be surprising if the telecoms industry would not commence aggressively selling the consumer the next G. That is 6G.
At this moment, the next 3 to 5 years of Capital spending are being planned out with the aim of having the 2024 budgets approved by November or December. In principle, the long-term plans, that is, until 2027/2028, have agreed on general principles. Though, with the current financial recession brewing. Such plans would likely be scrutinized as well.
I have, over the last year since I published this article, been asked whether I had any data on Ebitda over the period for Western Europe. I have spent considerable time researching this, and the below chart provides my best shot at such a view for the Telecom industry in Western Europe from the early days of mobile until today. This, however, should be taken with much more caution than the above Caex and Revenues, as individual Telco’ s have changed substantially over the period both in their organizational structure and how results have been represented in their annual reports.
Figure 4 illustrates the historical development of the EBITDA margin over the period from 1995 to 2022 and a projection of the possible trends from 2023 onwards. Caution: telcos’ corporate and financial structures (including reporting and associated transparency into details) have substantially changed over the period. The early first 10+ years are more uncertain concerning margin than the later years. Directionally it is representative of the European Telco industry. Take Deutsche Telekom AG, it “lost” 25% of its revenue between 2005 and 2015 (considering only German & European segments). Over the same period, it shredded almost 27% of its Opex.
Of course, Capex to Revenue ratios, any techno-economical ratio you may define, or cost distributions of any sort are in no way the whole story of a Telco life-and-budget cycle. Over time, due to possible structural changes in how Telcos operate, the past may not reflect the present and may even be less telling in the future.
Telcos may have merged with other Telcos (e.g., Mobile with Fixed), they may have non-Telco subsidiaries (i.e., IT consultancies, management consultancies, …), they may have integrated their fixed and mobile business units, they may have spun off their infrastructure, making use of towercos for their cell site needs (e.g., GD Towers, Vantage, Cellnex, American Towers …), open fibercos (e.g., Fiberhost Poland, Open Dutch Fiber, …) for their fiber needs, hyperscale cloud providers (e.g., AWS, Amazon, Microsoft Azure, ..) for their platform requirements. Capex and Opex will go left and right, up and down, depending on each of the above operational elements. All that may make comparing one Telco’s Capex with another Telco’s investment level and operational state-of-affairs somewhat uncertain.
I have dear colleagues who may be much more brutal. In general, they are not wrong but not as brutally right as their often high grounds could indicate. But then again, I am not a black-and-white guy … I like colors.
So, I believe that investment levels, or more generally, cost levels, can be meaningfully compared between Telcos. Cost, be it Opex or Capex, can be estimated or modeled with relatively high accuracy, assuming you are in the know. It can be compared with other comparables or non-comparables. Though not by your average financial controller with no technology knowledge and in-depth understanding.
Alas, with so many things in this world, you must understand what you are doing, including the limitations.
IT’S THAT TIME OF THE YEAR … CAPEX IS IN THE AIR.
It is the time of the year when many telcos are busy updating their business and financial planning for the following years. It is not uncommon to plan for 3 to 5 years ahead. It involves scenario planning and stress tests of those scenarios. Scenarios would include expectations of how the relevant market will evolve as well as the impact of the political and economic environment (e.g., covid lockdowns, the war in Ukraine, inflationary pressures, supply-chain challenges, … ) and possible changes to their asset ownership (e.g., infrastructure spin-offs).
Typically, between the end of the third or beginning of the fourth quarter, telecommunications businesses would have converged upon a plan for the coming years, and work will focus on in-depth budget planning for the year to come, thus 2024. This is important for the operational part of the business, as work orders and purchase orders for the first quarter of the following year would need to be issued within the current year.
The planning process can be sophisticated, involving many parts of the organization considering many scenarios, and being almost mathematical in its planning nature. It can be relatively simple with the business’s top-down financial targets to adhere to. In most instances, it’s likely a combination of both. Of course, if you are a publicly-traded company or part of one, your past planning will generally limit how much your new planning can change from the old. That is unless you improve upon your old plans or have no choice but to disappoint investors and shareholders (typically, though, one can always work on a good story). In general, businesses tend to be cautiously optimistic about uncertain business drivers (e.g., customer growth, churn, revenue, EBITDA) and conservatively pessimistic on business drivers of a more certain character (e.g., Capex, fixed cost, G&A expenses, people cost, etc..). All that without substantially and negatively changing plans too much between one planning horizon to the next.
Capital expense, Capex, is one of the foundations, or enablers, of the telco business. It finances the building, expansion, operation, and maintenance of the telco network, allowing customers to enjoy mobile services, fixed broadband services, TV services, etc., of ever-increasing quality and diversity. I like to look at Capex as the investments I need to incur in order to sustain my existing revenues, grow my revenues (preferably beating inflationary pressures), and finance any efficiency activities that will reduce my operational expenses in the future.
If we want to make the value of Capex to the corporation a little firmer, we need a little bit of financial calculus. We can write a company’s value (CV) as
With g being the expected growth rate in free cash flow in perpetuity, WACC is the Weighted Average Cost of Capital, and FCFF is the Free Cash Flow to the Firm (i.e., company) that we can write as follows;
FCFF = NOPLAT + Depreciation & Amortization (DA) – ∆ Working Capital – Capex,
with NOPLAT being the Net Operating Profit Less Adjusted Taxes (i.e., EBIT – Cash Taxes). So if I have two different Capex budgets with everything else staying the same despite the difference in Capex (if true life would be so easy, right?);
assuming that everything except the proposed Capex remains the same. With a difference of, for example, 10 Million euros, a future growth rate g = 0% (maybe conservative), and a WACC of 5% (note: you can find the latest average WACC data for the industry here, which is updated regularly by New York University Leonard N. Stern School of Business. The 5% chosen here serves as an illustration only (e.g., this was approximately representative of Telco Europe back in 2022, as of July 2023, it was slightly above 6%). You should always choose the weighted average cost of capital that is applicable to your context). The above formula would tell us that the investment plan having 10 Million euros less would be 200 Million euros more valuable (20× the Capex not spent). Anyone with a bit of (hands-on!) experience in budget business planning would know that the above valuation logic should be taken with a mountain of salt. If you have two Capex plans with no positive difference in business or financial value, you should choose the plan with less Capex (and don’t count yourself rich on what you did not do). Of course, some topics may require Capex without obvious benefits to the top or bottom line. Such examples are easy to find, e.g., regulatory requirements or geo-political risks force investments that may appear valueless or even value destructive. Those require meticulous considerations, and timing may often play a role in optimizing your investment strategy around such topics. In some cases, management will create a narrative around a corporate investment decision that fits an optimized valuation, typically hedging on one-sided inflated risks to the business if not done. Whatever decision is made, it is good to remember that Capex, and resulting Opex, is in most cases a certainty. The business benefits in terms of more revenue or more customers are uncertain as is assuming your business will be worth more in a number of years if your antennas are yellow and not green. One may call this the “Faith-based case of more Capex.”
Figure 5 provides an overview of Western Europe of annual Fixed & Mobile Capex, Total and Service Revenues, and Capex to Revenue ratio (in %). Source: New Street Research Western Europe data.
Figure 5 provides an overview of Western European telcos’ revenue, Capex, and Capex to Revenue ratio. Over the last five years, Western European telcos have been spending increasingly higher Capex levels. In 2021 the telecom Capex was 6 billion euros higher than what was spent in 2017, about 13% higher. Fixed and mobile service revenue increased by 14 billion euros, yielding a Capex to Service revenue ratio of 23% in 2021 compared to 20.6% in 2017. In most cases, the total revenue would be reported, and if luck has its way (or you are a subscriber to New Street Research), the total Capex. Thus, capturing both the mobile and the fixed business, including any non-service-related revenues from the company. As defined in this article, non-service-related revenues would comprise revenues from wholesales, sales of equipment (e.g., mobile devices, STB, and CPEs), and other non-service-specific revenues. As a rule of thumb, the relative difference between total and service-related revenues is usually between 1.1 to 1.3 (e.g., the last 5-year average for WEU was 1.17).
One of the main drivers for the Western European Capex has firstly been aggressive fiber-to-the-premise (FTTP) deployment and household fiber connectivity, typically measured in homes passed across most of the European metropolitan footprint as well as urban areas in general. As fiber covers more and more residential households, increased subscription to fiber occurs as well. This also requires substantial additional Capex for a fixed broadband business. Figure 6 illustrates the annual FTTP (homes passed) deployment volume in Western Europe as well as the total household fiber coverage.
Figure 6 above shows the fiber to the premise (FTTP) home passed deployment per anno from 2018 to 2021 Actual (source: European Commission’s “Broadband Coverage in Europe 2021” authored by Omdia et al.) and 2021 to 2025 projected numbers (i.e., this author’s own assessment). During the period from 2018 to 2021, household fiber coverage grew from 27% to 43% and is expected to grow to at least 71% by 2026 (not including overbuilt, thus unique household covered). The overbuilt data are based on a work in progress model and really should be seen as directional (it is difficult to get data with respect to the overbuilt).
A large part of the initial deployment has been in relatively dense urban areas as well as relying on aerial fiber deployment outside bigger metropolitan centers. For example, in Portugal, with close to 90% of households covered with fiber as of 2021, the existing HFC infrastructure (duct, underground passageways, …) was a key enabler for the very fast, economical, and extensive household fiber coverage there. Although many Western European markets will be reaching or exceeding 80% of fiber coverage in their urban areas, I would expect to continue to see a substantial amount of Capex being attributed. In fact, what is often overlooked in the assessment of the Capex volume being committed to fiber deployment, is that the unit-Capex is likely to increase substantially as countries with no aerial deployment option pick up their fiber rollout pace (e.g., Germany, the UK, Netherlands) and countries with an already relatively high fiber coverage go increasingly suburban and rural.
Figure 7 above shows the total fiber to the premise (FTTP) home remaining per anno from 2018 to 2021 Actual (source: European Commission’s “Broadband Coverage in Europe 2021” authored by Omdia et al.). The 2022 to 2030 projected remaining households are based on the author’s own assessment and does not consider overbuilt numbers.
The second main driver is in the domain of mobile network investment. The 5G radio access deployment has been a major driver in 2020 and 2021. It is expected to continue to contribute significantly to mobile operators Capex in the coming 5 years. For most Western European operators, the initial 5G deployment was at 700 MHz, which provides a very good 5G coverage. However, due to limited frequency spectral bandwidth, there are not very impressive speeds unless combined with a solid pre-existing 4G network. The deployment of 5G at 700 MHz has had a fairly modest effect on Mobile Capex (apart from what operators had to pay out in the 5G spectrum auctions to acquire the spectrum in the first place). Some mobile networks would have been prepared to accommodate the 700 MHz spectrum being supported by existing lower-order or classical antenna infrastructure. In 2021 and going forward, we will see an increasing part of the mobile Capex being allocated to 3.X GHz deployment. Far more sophisticated antenna systems, which co-incidentally also are far more costly in unit-Capex terms, will be taken into use, such as higher-order MiMo antennas from 8×8 passive MiMo to 32×32 and 64×64 active antennas systems. These advanced antenna systems will be deployed widely in metropolitan and urban areas. Some operators may even deploy these costly but very-high performing antenna systems in suburban and rural clutter with the intention to provide fixed-wireless access services to areas that today and for the next 5 – 7 years continue to be under-served with respect to fixed broadband fiber services.
Overall, I would also expect mobile Capex to continue to increase above and beyond the pre-2020 level.
As an external investor with little detailed insights into individual telco operations, it can be difficult to assess whether individual businesses or the industry are investing sufficiently into their technical landscape to allow for growth and increased demand for quality. Most publicly available financial reporting does not provide (if at all) sufficient insights into how capital expenses are deployed or prioritized across the many facets of a telco’s technical infrastructure, platforms, and services. As many telcos provide mobile and fixed services based on owned or wholesaled mobile and fixed networks (or combinations there off), it has become even more challenging to ascertain the quality of individual telecom operations capital investments.
Figure 8 illustrates why analysts like to plot Total Revenue against Total Capex (for fixed and mobile). It provides an excellent correlation. Though great care should be taken not to assume causation is at work here, i.e., “if I invest X Euro more, I will have Y Euro more in revenues.” It may tell you that you need to invest a certain level of Capex in sustaining a certain level of Revenue in your market context (i.e., country geo-socio-economic context). Source: New Street Research Western Europe data covering the following countries: AT, BE, DK, FI, FR, DE, GR, IT, NL, NO, PT, ES, SE, CH, and UK.
Why bother with revenues from the telco services? These would typically drive and dominate the capital investments and, as such, should relate strongly to the Capex plans of telcos. It is customary to benchmark capital spending by comparing the Capex to Revenue (see Figure 8), indicating how much a business needs to invest into infrastructure and services to obtain a certain income level. If nothing is stated, the revenue used for the Capex-to-Revenue ratio would be total revenue. For telcos with fixed and mobile businesses, it’s a very high-level KPI that does not allow for too many insights (in my opinion). It requires some de-averaging to become more meaningful.
THE TELCO TECHNOLOGY FACTORY
Figure 8 (below) illustrates the main capital investment areas and cost drivers for telecommunications operations with either a fixed broadband network, a mobile network, or both. Typically, around 90% of the capital expenditures will be invested into the technology factory comprising network infrastructure, products, services, and all associated with information technology. The remaining ca. 10% will be spent on non-technical infrastructures, such as shops, office space, and other non-tech tangible assets.
Figure 9 Telco Capex is spent across physical (or tangible) infrastructure assets, such as communications equipment, brick & mortar that hosts the equipment, and staff. Furthermore, a considerable amount of a telcos Capex will also go to human development work, e.g., for IT, products & services, either carried out directly by own staff or third parties (i.e., capitalized labor). The above illustrates the macro-levels that make out a mobile or fixed telecommunications network, and the most important areas Capex will be allocated to.
If we take the helicopter view on a telco’s network, we have the customer’s devices, either mobile devices (e.g., smartphone, Internet of Things, tablet, … ) or fixed devices, such as the customer premise equipment (CPE) and set-top box. Typically the broadband network connection to the customer’s premise would require a media converter or optical network terminator (ONT). For a mobile network, we have a wireless connection between the customer device and the radio access network (RAN), the cellular network’s most southern point (or edge). Radio access technology (e.g., 3G, 4G, or 5G) is very important determines for the customer experience. For a fixed network connection, we have fiber or coax (cable) or copper connecting the customer’s premise and the fixed network (e.g., street cabinet). Access (in general) follows the distribution of the customers’ locations and concentration, and their generated traffic is aggregated increasingly as we move north and up towards and into the core network. In today’s modern networks, big-fat-data broadband connections interconnect with the internet and big public data centers hosting both 3rd party and operator-provided content, services, and applications that the customer base demands. In many existing networks, data centers inside the operator’s own “walls” likewise will have service and application platforms that provide customers with more of the operator’s services. Such private data centers, including what is called micro data centers (μDCs) or edge DCs, may also host 3rd party content delivery networks that enable higher quality content services to a telco’s customer base due to a higher degree of proximity to where the customers are located compared to internet-based data centers (that could be located anywhere in the world).
Figure 10 illustrates break-out the details of a mobile as well as a fixed (fiber-based) network’s infrastructure elements, including the customers’ various types of devices.
Figure 10 illustrates that on a helicopter level, a fixed and a classical mobile network structure are reasonably similar, with the main difference of one network carrying the mobile traffic and the other the fixed traffic. The traffic in the fixed network tends to be at least ten larger than in the mobile network. They mainly differ in the access node and how it connects to the customer. For fixed broadband, the physical connection is established between, for example, the ONL (Optical Line Terminal) in the optical distribution network and ONT (Optical Line Terminal) at the customer’s home via a fiber line (i.e., wired). The wireless connection for mobile is between the Radio Node’s antenna and the end-user device. Note: AAS: Advanced Antenna System (e.g., MiMo, massive-MiMo), BBU: Base-band unit, CPE: Customer Premise Equipment, IOT: Internet of Things, IX: Internet Exchange, OLT: Optical Line Termination, and ONT: Optical Network Termination (same as ONU: Optical Network Unit).
From Figure 10 above, it should be clear that there are a lot of similarities between the mobile and fixed networks, with the biggest difference being that the mobile access network establishes a wireless connection to the customer’s devices versus the fixed access network physically wired connection to the device situated at the customer’s premises.
This is good news for fixed-mobile telecommunications operators as these will have considerable architectural and, thus, investment synergies due to those similarities. Although, the sad truth is that even today, many fixed-mobile telco companies, particularly incumbent, remain far away from having achieved fixed-mobile network harmonization and conversion.
Moreover, there are many questions to be asked as well as concerns when it comes to our industry’s Capex plans; what is the Capex required to accommodate data growth, are existing budgets allowing for sufficient network densification (to accommodate growth and quality), and what is the Capex trade-off between frequency spectrum acquisition, antenna technology, and site densification, how much Capex is justified to pursue the best network in a given market, what is the suitable trade-off between investing in fiber to the home and aggressive 5G deployment, should (incumbent) telco’s pursue fixed wireless access (FWA) and how would that impact their capital plans, what is the right antenna strategy, etc…
On a high level, I will provide guidance on many of the above questions, in this article and in forthcoming ones.
THE CAPEX STRUCTURE OF A TELECOM COMPANY.
When taking a macro look at Capex and not yet having a good idea about the breakdown between mobile and fixed investment levels, we are helped that on a macro level, the Capex categories are similar for a fixed and a mobile network. Apart from the last mile (access) in a fixed network is a fixed line (e.g., fiber, coax, or copper) and a wireless connection in a mobile network; the rest is comparable in nature and function. This is not surprising as a business with a fixed-mobile infrastructure would (should!) leverage the commonalities in transport and part of the access architecture.
In the fixed business, devices required to enable services on the fixed-line network at the fixed customers’ home (e.g., CPE, STB, …) are a capital expense driven by new customers and device replacement. This is not the case for mobile devices (i.e., an operational expense).
Figure 11 above illustrates the major Capex elements and their distribution defined by the median, lower and upper quantiles (the box), and lower and upper extremes (the whiskers) of what one should expect of various elements’ contribution to telco Capex. Note: CPE: Customer Premise Equipment, STB: Set-Top Box.
CUSTOMER PREMISE EQUIPMENT (CPE) & SET-TOP BOXES (STB) investments ARE between 10% to 20% of the TelEcoM Capex.
The capital investment level into Customer premise equipment (CPE) depends on the expected growth in the fixed customer base and the replacement of old or defective CPEs already in the fixed customer base. We would generally expect this to make out between 10% to 20% of the total Capex of a fixed-mobile telco (and 0% in a mobile-only business). When migrating from one access technology (e.g., copper/xDSL phase-out, coaxial cable) to another (e.g., fiber or hybrid coaxial cable), more Capex may be required. Similar considerations for set-top boxes (STB) replacement due to, for example, a new TV platform, non-compliance with new requirements, etc. Many Western European incumbents are phasing out their extensive and aging copper networks and replacing those with fiber-based networks. At the same time, incumbents may have substantial capital requirements phasing out their legacy copper-based access networks, the capital burden on other competitor telcos in markets where this is happening if such would have a significant copper-based wholesale relationship with the incumbent.
In summary, over the next five years, we should expect an increase in CPE-based Caped due to the legacy copper phase-out of incumbent fixed telcos. This will also increase the capital pressure in transport and access categories.
CPE & STB Capex KPIs: Capex share of Total and Capex per Gross Added Customer.
Capex modeling comment: Use your customer forecast model as the driver for new CPEs. Your research should give you an idea of the price range of CPEs used by your target fixed broadband business. Always include CPE replacement in the existing base and the gross adds for the new CPEs. Many fixed broadband retail businesses have been conservative in the capabilities of CPEs they have offered to their customer base (e.g., low-end cheaper CPEs, poor WiFi quality, ≤1Gbps), and it should be considered that these may not be sufficient for customer demand in the following years. An incumbent with a large install base of xDSL customers may also have a substantial migration (to fiber) cost as CPEs are required to be replaced with fiber cable CPEs. Due to the current supply chain and delivery issues, I would assume that operators would be willing to pay a premium for getting critical stock as well as having priority delivery as stock becomes available (e.g., by more expensive shipping means).
Core network & service platformS, including data centers, investments ARE between 8% to 12% of the telecom Capex.
Core network and service platforms should not take up more than 10% of the total Capex. We would regard anything less than 5% or more than 15% as an anomaly in Capital prioritization. This said, over the next couple of years, many telcos with mobile operations will launch 5G standalone core networks, which is a substantial change to the existing core network architecture. This also raises the opportunity for lifting and shifting from monolithic systems or older cloud frameworks to cloud-native and possibly migrating certain functions onto public cloud domains from one or more hyperscalers (e.g., AWS, Azure, Google). As workloads are moved from telco-owned data centers and own monolithic core systems, telco technology cost structure may change from what prior was a substantial capital expense to an operational expense. This is particularly true for software-related developments and licensing.
Another core network & service platform Capex pressure point may come from political or investor pressure to replace Chinese network elements, often far removed from obsolescence and performance issues, with non-Chinese alternatives. This may raise the Core network Capex level for the next 3 to 5 years, possibly beyond 12%. Alas, this would be temporary.
In summary, the following topics would likely be on the Capex priority list;
1. Life-cycle management investments (I like to call Business-as-Usual demand) into software and hardware maintenance, end-of-life replacements, growth (software licenses, HW expansions), and miscellaneous topics. This area tends to dominate the Capex demand unless larger transformational projects exist. It is also the first area to be de-prioritized if required. Working with Priority 1, 2, and 3 categorizations is a good Capital planning methodology. Where Priority 1 is required within the following budget year 1, Prio. 2 is important but can wait until year two without building up too much technical debt and Prio. 3 is nice to have and not expected to be required for the next two subsequent budget years.
3. Network cloudification, initially lift-and-shift with subsequent cloud-native transformation. The trigger point will be enabling the deployment of the 5G standalone (SA) core. Operators will also take the opportunity to clean up their data centers and network core location (timeline: 24 – 36 months).
4. Although edge computing data centers (DC) typically are supposed to support the radio access network (e.g., for Open-RAN), the capital assignment would be with the core network as the expertise for this resides here. The intensity of this Capex (if built by the operator, otherwise, it would be Opex) will depend on the country’s size and fronthaul/backhaul design. The investment trigger point would generally commence on Open-RAN deployment (e.g., 1&1 & Telefonica Germany). The edge DC (or μDC) would most like be standard container-sized (or half that size) and could easily be provided by independent towerco or specific edge-DC 3rd party providers lessening the Capex required for the telco. For smaller geographies (e.g., Netherlands, Denmark, Austria, …), I would not expect this item to be a substantial topic for the Capex plans. Mainly if Open-RAN is not being pursued over the next 5 – 10 years by mainstream incumbent telcos.
5. Chinese supplier replacement. The urgency would depend on regulatory pressure, whether compensation is provided (unlikely) or not, and the obsolescence timeline of the infrastructure in question. Given the high quality at very affordable economics, I expect this not to have the biggest priority and will be executed within timelines dictated more by economics and obsolescence timelines. In any case, I expect that before 2025 most European telcos will have phased out Chinese suppliers from their Core Networks, incl. any Service platforms in use today (timeline: max. 36 months).
6. Cybersecurity investments strengthen infrastructure, processes, and vital data residing in data centers, service platforms, and core network elements. I expect a substantial increase in Capex (and Opex) arising from the telco’s focus on increasing the cyber protection of their critical telecom infrastructure (timeline: max 18 months with urgency).
Core Capex KPIs: Capex share of Total (knowing the share, it is straightforward to get the Capex per Revenue related to the Core), Capex per Incremental demanded data traffic (in Gigabits and Gigabyte per second), Capex per Total traffic, Capex per customer.
Capex modeling comment: In case I have little specific information about an operator’s core network and service platforms, I would tend to model it as a Euro per Customer, Euro per-incremental customer, and Euro per incremental traffic. Checking that I am not violating my Capex range that this category would typically fall within (e.g., 8% to 12%). I would also have to consider obsolescence investments, taking, for example, a percentage of previous cumulated core investments. As mobile operators are in the process, or soon will be, of implementing a 5G standalone core, having an idea of the number of 5G customers and their traffic would be useful to factor that in separately in this Capex category.
Estimating the possible Capex spend on Edge-RAN locations, I would consider that I need ca. 1 μDC per 450 to 700 km2 of O-RAN coverage (i.e., corresponding to a fronthaul distance between the remote radio and the baseband unit of 12 to 15 km). There may be synergies between fixed broadband access locations and the need for μ-datacenters for an O-RAN deployment for an integrated fixed-mobile telco. I suspect that 3rd party towercos, or alike, may eventually also offer this kind of site solutions, possibly sharing the cost with other mobile O-RAN operators.
Transport – core, metro & aggregation investments are between 5% to 15% of Telecom Capex.
The transport network consists of an optical transport network (OTN) connecting all infrastructure nodes via optical fiber. The optical transport network extends down to the access layer from the Core through the Metro and Aggregation layers. On top, the IP network ensures logical connection and control flow of all data transported up and downstream between the infrastructure nodes. As data traffic is carried from the edge of the network upstream, it is aggregated at one or several places in the network (and, of course, disaggregated in the downstream direction). Thus, the higher the transport network, the more bandwidth is supported on the optical and the IP layers. Most of the Capex investment needs would ensure that sufficient optical and IP capacity is available, supporting the growth projections and new service requirements from the business and that no bottlenecks can occur that may have disastrous consequences on customer experience. This mainly comes down to adding cards and ports to the already installed equipment, upgrading & replacing equipment as it reaches capacity or quality limitations, or eventually becoming obsolete. There may be software license fees associated with growth or the introduction of new services that also need to be considered.
Figure 12 above illustrates (high-level) the transport network topology with the optical transport network and IP networking on top. Apart from optical and IP network equipment, this area often includes investments into IP application functions and related hardware (e.g., BNG, DHCP, DNS, AAA RADIUS Servers, …), which have not been shown in the above. In most cases, the underlying optical fiber network would be present and sufficiently scalable, not requiring substantial Capex apart from some repair and minor extensions. Note DWDM: Dense Wavelength-Division multiplexing is an optical fiber multiplexing technology that increases the bandwidth utilization of a FON, BNG: Border Network Gateway connecting subscribers to a network or an internet service providers (ISP) network, important in wholesale arrangements where a 3rd party provides aggregation and access. DHCP: Dynamic Host Configuration Protocol providing IP address allocation and client configurations. AAA: Authentication, Authorization, and Accounting of the subscriber/user, RADIUS: Remote Authentication Dial-In User Service (Server) providing the AAA functionalities.
Although many telcos operate fixed-mobile networks and might even offer fixed-mobile converged services, they may still operate largely separate fixed and mobile networks. It is not uncommon to find very different transport design principles as well as supplier landscapes between fixed and mobile. The maturity, when each was initially built, and technology roadmaps have historically been very different. The fixed traffic dynamics and data volumes are several times higher than mobile traffic. The geographical presence between fixed and mobile tends to be very different (unless the telco of interest is the incumbent with a considerable copper or HFC network). However, the biggest reason for this state of affairs has been people and technology organizations within the telcos resisting change and much more aggressive transport consolidation, which would have been possible.
The mobile traffic could (should!) be accommodated at least from the metro/aggregation layers and upstream through the core transport. There may even be some potential for consolidation on front and backhauls that are worth considering. This would lead to supplier consolidation and organizational synergies as the technology organizations converged into a fixed-mobile engineering organization rather than two separate ones.
I would expect the share of Capex to be on the higher end of the likely range and towards the 10+% at least for the next couple of years, mainly if fixed and mobile networks are being harmonized on the transport level, which may also create an opportunity reduce and harmonize the supplier landscape.
In summary, the following topics would likely be on the Capex priority list;
Life-cycle management (business-as-usual) investments, accommodating growth including new service and quality requirements (annual business-as-usual). There are no indications that the traffic or mobile traffic growth rate over the next five years will be very different from the past. If anything, the 5-year CAGR is slightly decreasing.
Consolidating fixed and mobile transport networks (timelines: 36 to 60 months, depending on network size and geography). Some companies are already in the process of getting this done.
Chinese supplier replacement. To my knowledge, there are fewer regulatory discussions and political pressure for telcos to phase out transport infrastructure. Nevertheless, with the current geopolitical climate (and the upcoming US election in 2024), telcos need to consider this topic very carefully; despite economic (less competition, higher cost), quality, and possible innovation, consequences may result in a departure from such suppliers. It would be a natural consideration in case of modernization needs. An accelerated phase-out may be justified to remove future risks arising from geopolitical pressures.
While I have chosen not to include the Access transport under this category, it is not uncommon to see its budget demand assigned to this category, as the transport side of access (fronthaul and backhaul transport) technically is very synergetic with the transport considerations in aggregation, metro, and core.
Transport Capex KPIs: Capex share of Total, the amount of Capex allocated to Mobile-only and Fixed-only (and, of course, to a harmonized/converged evolved transport network), The Utilization level (if data is available or modeled to this level). The amount of Capex-spend on fiber deployment, active and passive optical transport, and IP.
Capex modeling comment: I would see whether any information is available on a number of core data centers, aggregation, and metro locations. If this information is available, it is possible to get an impression of both core, aggregation, and metro transport networks. If this information is not available, I would assume a sensible transport topology given the particularities of the country where the operator resides, considering whether the operator is an incumbent fixed operator with mobile, a mobile-only operation, or a mobile operator that later has added fixed broadband to its product portfolio. If we are not talking about a greenfield operation, most, if not all, will already be in place, and mainly obsolescence, incremental traffic, and possible transport network extensions would incur Capex. It is important to understand whether fixed-mobile operations have harmonized and integrated their transport infrastructure or large-run those independently of each other. There is substantial Capex synergy in operating an integrated transport network, although it will take time and Capex to get to that integration point.
Access investments are typically between 35% to 50% of the Telecom Capex.
Figure 13 (above) is similar to Figure 8 (above), emphasizing the access part of Fixed and Mobile networks. I have extended the mobile access topology to capture newer development of Open-RAN and fronthaul requirements with pooling (“centralizing”) the baseband (BBU) resources in an edge cloud (e.g., container-sized computing center). Fronthaul & Open-RAN poses requirements to the access transport network. It can be relatively costly to transform a legacy RAN backhaul-only based topology to an Open-RAN fronthaul-based topology. Open-RAN and fronthaul topologies for Greenfield deployments are more flexible and at least require less Capex and Opex.
Mobile Access Capex.
I will define mobile access (or radio access network, RAN) as everything from the antenna on the site location that supports the customers’ usage (or traffic demand) via the active radio equipment (on-site or residing in an edge-cloud datacenter), through the fronthaul and backhaul transport, up to the point before aggregation (i.e., pre-aggregation). It includes passive and active infrastructure on-site, steal & mortar or storage container, front- and backhaul transport, data center software & equipment (that may be required in an edge data center), and any other hardware or software required to have a functional mobile service on whatever G being sold by the mobile operator.
Figure 14 above illustrates a radio access network architecture that is typically deployed by an incumbent telco supporting up to 4G and 5G. A greenfield operation on 5G (and maybe 4G) could (maybe should?) choose to disaggregate the radio access node using an open interface, allowing for a supplier mix between the remote radio head (RRH and digital frontend) at the site location and the centralized (or distributed) baseband unit (BBU). Fronthaul connects the antenna and RRH with a remote BBU that is situated at an edge-cloud data center (e.g., storage container datacenter unit = micro-data center, μDC). Due to latency constraints, the distance between the remote site and the BBU should not be much more than 10 km. It is customary to name the 5G new radio node a gNB (g-Node-B) like the 4G radio node is named eNB (evolved-Node-B).
When considering the mobile access network, it is good to keep in mind that, at the moment, there are at least two main flavors (that can be mixed, of course) to consider. (1) A classical architecture with the site’s radio access hardware and software from a single supplier, with a remote radio head (RRH) as well as digital frontend processing at or near the antenna. The radio nodes do not allow for mixing suppliers between the remote RF and the baseband. Radio nodes are connected to backhaul transmission that may be enabled by fiber or microwave radios. This option is simple and very well-proven. However, it comes with supplier lock-in and possibly less efficient use of baseband resources as these are likewise fixed to the radio node that the baseband unit is installed. (2) A new Open- or disaggregated radio access network (O-RAN), with the Antenna and RHH at the site location (the RU, radio unit in O-RAN), then connected via fronthaul (≤ 10 – 20 km distance) to a μDC that contains the baseband unit (the DU, distributed unit in O-RAN). The μDC would then be connected to the backhaul that connects northbound to the Central Unit (CU), aggregation, and core. The open interface between the RRH (and digital frontend) and the BBU allows different suppliers and hosts the RAN-specific software on common off-the-shelf (COTS) computing equipment. It allows (in theory) for better scaling and efficiency with the baseband resources. However, the framework has not been standardized by the usual bodies of standardization (e.g., 3GPP) and is not universally accepted as a common standard that all telco suppliers would adhere to. It also has not reached maturity yet (sort of obvious) and is currently (as of July 2022) seen to be associated with substantial cyber-security risks (re: maturity). It may be an interesting deployment model for greenfield operations (e.g., Rakuten Mobile Japan, Jio India, 1&1 Germany, Dish Mobile USA). The O-RAN options are depicted in Figure 15 below.
Figure 15 The above illustrates a generic Open RAN architecture starting with the Advanced Antenna System (AAS) and the Radio Unit (RU). The RU contains the functionality associated with the (OSI model) layer 1, partitioned into the lower layer 1 functions with the upper layer 1 functions possibly moved out of the RU and into the Distributed Unit (DU) connected via the fronthaul transport. The DU, which typically will be connected to several RUs, must ensure proper data link management, traffic control, addressing, and reliable communication with the RU (i.e., layer 2 functionalities). The distributed unit connects via the mid-haul transport link to the so-called Central Unit (CU), which typically will be connected to several DUs. The CU plays an important role in the overall ORAN architecture, acting as a central control and management vehicle that coordinates the operations of DUs and RUs, ensuring an efficient and effective operation of the ORAN network. As may be obvious, from the summary of its functionality, layer 3 functionalities reside in the CU. The Central Unit connects via backhaul, aggregation, and core transport to the core network.
For established incumbent mobile operators, I do not see Option (2) as very attractive, at least for the next 5 – 7 years when many legacy technologies (i.e., non-5G) remain to be supported. The main concern should be the maturity, lack of industry-wise standardization, as well as cost of transforming existing access transport networks into compliance with a fronthaul framework. Most likely, some incumbents, the “brave” ones, will deploy O-RAN for 1 or a few 5G bands and keep their legacy networks as is. Most incumbent mobile operators will choose (actually have chosen already) conventional suppliers and the classical topology option to provide their 5G radio access network as it has the highest synergy with the access infrastructure already deployed. Thus, if my assertion is correct, O-RAN will only start becoming mass-market mainstream in 5 to 7 years, when existing deployments become obsolete, and may ultimately become mass-market viable by the introduction of 6G towards the end of the twenties. The verdict is very much still out there, in my opinion.
Planning the mobile-radio access networks Capex requirements is not (that) difficult. Most of it can be mathematically derived and be easily assessed against growth expectations, expected (or targeted) network utilization (or efficiency), and quality. The growth expectations (should) come from consumer and retail businesses’ forecast of mobile customers over the next 3 to 5 years, their expected usage (if they care, otherwise technology should), or data-plan distribution (maybe including technology distributions, if they care. Otherwise, technology should), as well as the desired level of quality (usually the best).
Figure 16 above illustrates a typical cellular planning structural hierarchy from the sector perspective. One site typically has 3 sectors. One sector can have multiple cells depending on the frequency bands installed in the (multi-band) antennas. Massive MiMo antenna systems provide target cellular beams toward the user’s device that extend the range of coverage (via the beam). Very fast scheduling will enable beams to be switched/cycled to other users in the covered sector (a bit oversimplified). Typically, the sector is planned according to the cell utilization, thus on a frequency-by-frequency basis.
Figure 17 illustrates that most investment drivers can be approached as statistical distributions. Those distributions will tell us how much investment is required to ensure that a critical parameter X remains below a pre-defined critical limit Xc within a given probability (i.e., the proportion of the distribution exceeding Xc). The planning approach will typically establish a reference distribution based on actual data. Then based on marketing forecasts, the planners will evolve the reference based on the expected future usage that drives the planning parameter. Example: Let X be the customer’s average speed in a radio cell (e.g., in a given sector of an antenna site) in the busy hour. The business (including technology) has decided it will target 98% of its cells and should provide better than 10 Mbps for more than 50% of the active time a customer uses a given cell. Typically, we will have several quality-based KPIs, and the more breached they are, the more likely it will be that a Capex action is initiated to improve the customer experience.
Network planners will have access to much information down to the cell level (i.e., the active frequency band in a given sector). This helps them develop solid planning and statistical models that provide confidence in the extrapolation of the critical planning parameters as demand changes (typically increases) that subsequently drive the need for expansions, parameter adjustments, and other optimization requirements. As shown in Figure 17 above, it is customary to allow for some cells to breach a defined critical limit Xc, usually though it is kept low to ensure a given customer experience level. Examples of planning parameters could be cell (and sector) utilization in the busy hour, active concurrent users in cell (or sector), duration users spend at a or lower deemed poor speed level in a given cell, physical resource block (the famous PRB, try to ask what it stands for & what it means😉) utilization, etc.
The following topics would likely be on the Capex priority list;
New radio access deployment Capex. This may be for building new sites for coverage, typically in newly built residential areas, and due to capacity requirements where existing sites can no longer support the demand in a given area. Furthermore, this Capex also covers a new technology deployment such as 5G or deploying a new frequency band requiring a new antenna solution like 3.X GHz would do. As independent tower infrastructure companies (towerco) increasingly are used to providing the required passive site infrastructure solution (e.g., location, concrete, or steel masts/towers/poles), this part will not be a Capex item but be charged as Opex back to the mobile operator. From a European mobile radio access network Capex perspective, the average cost of a total site solution, with active as well as passive infrastructure, should have been reduced by ca. 100 thousand plus Euro, which may translate into a monthly Opex charge of 800 to 1300 Euro per site solution. It should be noted that while many operators have spun off their passive site solutions to third parties and thus effectively reduced their site-related Capex, the cost of antennas has increased dramatically as operators have moved away from classical simple SiSo (Single-in Singe-out) passive antennas to much more advanced antenna systems supporting multiple frequency bands, higher-order antennas (e.g., MiMo) and recently also started deploying active antennas (i.e., integrated amplifiers). This is largely also driven by mobile operators commissioning more and more frequency bands on their radio-access sites. The planning horizon needs at least to be 2 years and preferably 3 to 5 years.
Capex investments that accommodate anticipated radio access growth and increased quality requirements. It is normal to be between 18 – 24 months ahead of the present capacity demand overall, accepting no more than 2% to 5% of cells (in BH) to breach a critical specification limit. Several such critical limits would be used for longer-term planning and operational day-to-day monitoring.
Life-cycle management (business-as-usual) investments such as software annual fees, including licenses that are typically structured around the technologies deployed (e.g., 2G, 3G, 4G, and 5G) and active infrastructure modernization replacing radio access equipment (e.g., baseband units, radio units, antennas, …) that have become obsolete. Site reworks or construction optimization would typically be executed (on request from the operator) by the Towerco entity, where the mobile operator leases the passive site infrastructure. Thus, in such instances may not be a Capex item but charged back as an Operational expense to the telco.
Even if there have been fewer regulatory discussions and political pressure for telcos to phase out radio access, Chinese supplier replacement should be considered. Nevertheless, with the current geopolitical climate (and the upcoming US election), telcos need to consider this topic very carefully; despite economic (less competition, higher cost), quality, and possible innovation, consequences may result in a departure from such suppliers. It would be a natural consideration in case of modernization needs. An accelerated phase-out may be justified to remove future risks arising from geopolitical pressures, although it would result in above-and-beyond capital commitment over a shorter period than otherwise would be the case. Telco valuation may suffer more in the short to medium term than otherwise would have been the case with a more natural phaseout due to obsolescence.
Mobile Access Capex KPIs: Capex share of Total, Access Utilization (reported/planned data traffic demand to the data traffic that could be supplied if all or part of the spectrum was activated), Capex per Site location, Capex per Incremental data traffic demand (in Gigabyte and Gigabit per second which is the real investment driver), Capex per Total Traffic (in Gigabyte and Gigabit per second), Capex per Mobile Customer and Capex to Mobile Revenue (preferably service revenue but the total is fine if the other is not available). As a rule of thumb, 50% of a mobile network typically covers rural areas, which also may carry less than 20% of the total data traffic.
Whether actual and planned Capex is available or an analyst is modeling it, the above KPIs should be followed over an extended period. A single year does not tell much of a story.
Capex modeling comment: When modeling the Capex required for the radio access network, you need to have an idea about how many sites your target telco has. There are many ways to get to that number. In most European countries, it is a matter of public record. Most telcos, nowadays, rarely build their own passive site infrastructure but get that from independent third-party tower companies (e.g., CellNex w. ca. 75k locations, Vantage Towers w. ca. 82k locations, … ) or site-share on another operators site locations if available. So, modeling the RAN Capex is a matter of having a benchmark of the active equipment, knowing what active equipment is most likely to be deployed and how much. I see this as being an iterative modeling process. Given the number of sites and historical Capex, it is possible to come to a reasonable estimate of both volumes of sites being changed and the range of unit Capex (given good guestimates of active equipment pricing range). Of course, in case you are doing a Capex review, the data should be available to you, and the exercise should be straightforward. The mobile Capex KPIs above will allow for consistency checks of a modeling exercise or guide a Capex review process.
I recommend using the classical topology described above when building a radio access model. That is unless you have information that the telco under analysis is transforming to a disaggregated topology with both fronthaul and backhaul. Remember you are not only required to capture the Capex for what is associated with the site location but also what is spent on the access transport. Otherwise, there is a chance that you over-estimate the unit-Capex for the site-related investments.
It is also worth keeping in mind that typically, the first place a telecom company would cut Capex (or down-prioritize) is pressured during the planning process would be in the radio access network category. The reason is that the site-related unitary capex tends to be incredibly well-defined. If you reduce your rollout to 100 site-related units, you should have a very well-defined quantum of Capex that can be allocated to another category. Also, the operational impact of cutting in this category tends to be very well-defined. Depending on how well planned the overall Capex has been done, there typically would be a slack of 5% to 10% overall that could be re-assigned or ultimately reduced if financial results warrant such a move.
Fixed Access Capex.
As mobile access, fixed access is about getting your service out to your customers. Or, if you are a wholesale provider, you can provide the means of your wholesale customer reaching their customer by providing your own fixed access transport infrastructure. Fixed access is about connecting the home, the office, the public institution (e.g., school), or whatever type of dwelling in general.
Figure 18 illustrates a fixed access network and its position in the overall telco architecture. The following make up the ODN (Optical Distribution Network); OLT: Optical Line Termination, ODF: Optical Distribution Frame, POS: Passive Optical Splitter, ONT: Optical Network Termination. At the customer premise, besides the ONT, we have the CPE: Customer Premise Equipment and the STB: Set-Top Box. Suppose you are an operator that bought wholesale fixed access from another telco’ (incl. Open Access Providers, OAPs). In that case, you may require a BNG to establish the connection with your customer’s CPE and STB through the wholesale access network.
As fiber optical access networks are being deployed across Europe, this tends to be a substantial Capex item on the budgets of telcos. Here we have two main Capex drivers. First is the Capex for deploying fibers across urban areas, which provides coverage for households (or dwellings) and is measured as Capex-per-homes passed. Second is the Capex required for establishing the connection to households (or dwellings). The method of fiber deployment is either buried, possibly using existing ducts or underground passageways, or via aerial deployment using established poles (e.g., power poles or street furniture poles) or new poles deployed with the fiber deployment. Aerial deployment tends to incur lower Capex than buried fiber solutions due to requiring less civil work. The OLT, ODF, POS, and optical fiber planning, design, and build to provide home coverage depends on the home-passed deployment ambition. The fiber to connect a home (i.e., civil work and materials), ONT, CPE, and STBs are driven by homes connected (or FTTH connected). Typically, CPE and STBs are not included in the Access Capex but should be accounted for as a separate business-driven Capex item.
The network solutions (BNG, OLT, Routers, Switches, …) outside the customer’s dwelling come in the form of a cabinet and appropriate cards to populate the cabinet. The cards provide the capacity and serviced speed (e.g., 100 Mbps, 300 Mbps, 1 Gbps, 10 Gbps, …) sold to the fixed broadband customer. Moreover, for some of the deployed solutions, there is likely a mandatory software (incl. features) fee and possibly both optional and custom-specific features (although rare to see that in mainstream deployments). It should be clear (but you would be surprised) that ONT and CPE should support the provisioned speed of the fixed access network. The customer cannot get more quality than the minimum level of either the ONT, CPE, or what the ODN has been built to deliver. In other words, if the networking cards have been deployed only to support up to 1 Gbps and your ONT, and CPE may support 3 Gbps or more, your customer will not be able to have a service beyond 1 Gbps. Of course, the other way around as well. I cannot stress enough the importance of longer-term planning in this respect. Your network should be as flexible as possible in providing customer services. It may seem that Capex savings can be made by only deploying capacity sold today or may be required by business over the next 12 months. While taking a 3 to 5-year view on the deployed network capacity and ONT/CPEs provided to customers avoids having to rip out relatively new equipment or finance the significant replacement of obsolete customer premise equipment that no longer can support the services required.
When we look at the economic drivers for fixed access, we can look at the capital cost of deploying a kilometer of fiber. This is particularly interesting if we are only interested in the fiber deployment itself and nothing else. Depending on the type of clutter, deployment, and labor cost occur. Maybe it is more interesting to bundle your investment into what is required to pass a household and what is required to connect a household (after it has been passed). Thus, we look at the Capex-per-home (or dwellings) passed and separate the Capex to connect an individual customer’s premise. It is important to realize that these Capex drivers are not just a single value but will depend on the household density depends on the type of area the deployment happens. We generally expect dense urban clutters to have a high dwelling density; thus, more households are covered (or passed) per km of fiber deployed. Dense-urban areas, however, may not necessarily hold the highest density of potential residential customers and hold less retail interest in the retail business. Generally, urban areas have higher household densities (including residential households) than sub-urban clutter. Rural areas are expected to have the lowest density and, thus, the most costly (on a household basis) to deploy.
Figure 19, just below, illustrates the basic economics of buried (as opposed to aerial) fiber for FTTH homes passed and FTTH homes connected. Apart from showing the intuitive economic logic, the cost per home passed or connected is driven by the household density (note: it’s one driver and fairly important but does not capture all the factors). This may serve as a base for rough assessments of the cost of fiber deployment in homes passed and homes connected as a function of household density. I have used data in the Fiber-to-the-Home Council Europe report of July 2012 (10 years old), “The Cost of Meeting Europe’s Network Needs”, and have corrected for the European inflationary price increase since 2012 of ca. 14% and raised that to 20% to account for increased demand for FTTH related work by third parties. Then I checked this against some data points known to me (which do not coincide with the cities quoted in the chart). These data points relate to buried fiber, including the homes connected cost chart. Aerial fiber deployment (including home connected) would cost less than depicted here. Of course, some care should be taken in generalizing this to actual projects where proper knowledge of the local circumstances is preferred to the above.
Figure 19 The “chicken and egg” of connecting customers’ premises with fiber and providing them with 100s of Mbps up to Gbps broadband quality is that the fibers need to pass the home first before the home can be connected. The cost of passing a premise (i.e., the home passed) and connecting a premise (home connected) should, for planning purposes, be split up. The cost of rolling out fiber to get homes-passed coverage is not surprisingly particularly sensitive to household density. We will have more households per unit area in urban areas compared to rural areas. Connecting a home is more sensitive to household density in deep rural areas where the distance from the main fiber line connection point to the household may be longer. The above cost curves are for buried fiber lines and are in 2021 prices.
Aerial fiber deployment would generally be less capital-intensive due to faster and easier deployment (less civil work, including permitting) using pre-existing (or newly built) poles. Not every country allows aerial deployment or even has the infrastructure (i.e., poles) available, which may be medium and low-voltage poles (e.g., for last-mile access). Some countries will have a policy allowing only buried fibers in the city or metropolitan areas and supporting pole infrastructure for aerial deployment in sub-urban and rural clutters. I have tried to illustrate this with Figure 18 below, where the pie charts show the aerial potential and share that may have to be assigned to buried fiber deployment.
Figure 20 above illustrates the amount of fiber coverage (i.e., in terms of homes passed) in Western European markets. The number for 2015 and 2021 is based on European Commission’s “Broadband Coverage in Europe 2021” (authored by Omdia et al.). The 2025 & 2031 coverage numbers are my extrapolation of the 5-year trend leading up to 2021, considering the potential for aerial versus buried deployment. Aerial making accelerated deployment gains is more likely than in markets that only have buried fiber as a possibility, either because of regulation or lack of appropriate infrastructure for aerials. The only country that may be below 50% FTTH coverage in 2025 is Germany (i.e., DE), with a projected 39% of homes passed by 2025. Should Germany aim for 50% instead, they would have to do ca. 15 million households passed or, on average, 3 million a year from 2021 to 2025. Maximum Germany achieved in one year was in 2020, with ca. 1.4 million homes passed (i.e., Covid was good for getting “things done”). In 2021 this number dropped to ca. 700 thousand or half of the 2020 number. The maximum any country in Europe has done in one year was France, with 2.9 million homes passed in 2018. However, France does allow for aerial fiber deployment outside major metropolitan areas.
Figure 21 above provides an overview across Western Europe for the last 5 years (2016 – 2021) of average annual household fiber deployment, the maximum done in one year in the previous 5 years, and the average required to achieve household coverage in 2026 shown above in Figure 20. For Germany (DE), the average deployment pace of 3.23 homes passed per year (orange bar) would then result in a coverage estimate of 25%. I don’t see any practical reasons for the UK, France, and Italy not to make the estimated household coverage by 2026, which may exceed my estimates.
From a deployment pace and Capex perspective, it is good to keep in mind that as time goes by, the deployment cost per household is likely to increase as household density reduces when the deployment moves from metropolitan areas toward suburban and rural. Thus, even if the deployment pace may reduce naturally for many countries in Figure 20 towards 2025, absolute Capex may not necessarily reduce accordingly.
In summary, the following topics would likely be on the Capex priority list;
Continued fiber deployment to achieve household coverage. Based on Figure 17, at household (HH) densities above 500 per km2, the unit Capex for buried fiber should be below 900 Euro per HH passed with an average of 600 Euro per HH passed. Below 500 HH per km2, the cost increases rapidly towards 3,000 Euro per HH passed. The aerial deployment will result in substantially lower Capex, maybe with as much as 50% lower unit Capex.
As customers subscribe, the fiber access cost associated with connecting homes (last-mile connectivity) will need to be considered. Figure 17 provides some guidance regarding the quantum-Euro range expected for buried fiber. Aerial-based connections may be somewhat cheaper.
Life-cycle management (business-as-usual) investments, modernization investments, accommodating growth including new service and quality requirements (annual business as usual). Typically it would be upgrading OLT, ONTs, routers, and switches to support higher bandwidth requirements upgrading line cards (or interface cards), and moving from ≤100 Mbps to 1 Gbps and 10 Gbps. Many telcos will be considering upgrading their GPON (Gigabit Passive Optical Networks, 2.5 Gbps↓ / 1.2 Gbps↑) to provide XGPON (10 Gbps↓ / 2.5 Gbps↑) or even XGSPON services (10 Gbps↓ / 10 Gbps↑).
Chinese supplier exposure and risks (i.e., political and regulatory enforcement) may be an issue in some Western European markets and require accelerated phase-out capital needs. In general, I don’t see fixed access infrastructure being a priority in this respect, given the strong focus on increasing household fiber coverage, which already takes up a lot of human and financial resources. However, this topic needs to be considered in case of obsolescence and thus would be a business case and performance-driven with a risk adjustment in dealing with Chinese suppliers at that point in time.
Fixed Access Capex KPIs: Capex share of Total, Capex per km, Number of HH passed and connected, Capex per HH passed, Capex per HH connected, Capex to Incremental Traffic, GPON, XGPON and XGSPON share of Capex and Households connected.
Whether actual and planned Capex is available or an analyst is modeling it, the above KPIs should be followed over an extended period. A single year does not tell much of a story.
Capex modeling comment: In a modeling exercise, I would use estimates for the telco’s household coverage plans as well as the expected household-connected sales projections. Hopefully, historical numbers would be available to the analyst that can be used to estimate the unit-Capex for a household passed and a household connected. You need to have an idea of where the telco is in terms of household density, and thus as time goes by, you may assume that the cost of deployment per household increases somewhat. For example, use Figure 18 to guide the scaling curve you need. The above-fixed access Capex KPIs should allow checking for inconsistencies in your model or, if you are reviewing a Capex plan, whether that Capex plan is self-consistent with the data provided.
If anyone would have doubted it, there is still much to do with fiber optical deployment in Western Europe. We still have around 100+ million homes to pass and a likely capital investment need of 100+ billion euros. Fiber deployment will remain a tremendously important investment area for the foreseeable future.
Figure 22 shows the remaining fiber coverage in homes passed based on 2021 actuals for urban and rural areas. In general, it is expected that once urban areas’ coverage has reached 80% to 90%, the further coverage-based rollout will reduce. Though, for attractive urban areas, overbuilt, that is, deploying fiber where there already are fibers deployed, is likely to continue.
Figure 23 The top illustrates the next 5 years’ weekly rollout to reach an 80% to 90% household coverage range by 2025. The bottom, it shows an estimate of the remaining capital investment required to reach that 80% to 90% coverage range. This assessment is based on 2021 actuals from the European Commission’s “Broadband Coverage in Europe 2021” (authored by Omdia et al.); the weekly activity and Capex levels are thus from 2022 onwards.
In many Western European countries, the pace is expected to be increased considerably compared to the previous 5 years (i.e., 2016 – 2021). Even if the above figure may be over-optimistic, with respect to the goal of 2026, the European ambition for fiberizing European markets will impose a lot of pressure on speedy deployment.
IT investment levels are typically between 15% and 25% of Telecom Capex.
IT may be the most complex area to reach a consensus on concerning Capex. In my experience, it is also the area within a telco with the highest and most emotional discussion overhead within the operations and at a Board level. Just like everyone is far better at driving a car than the average driver, everyone is far better at IT than the IT experts and knows exactly what is wrong with IT and how to make IT much better and much faster, and much cheaper (if there ever was an area in telco-land where there are too many cooks).
Why is that the case? I tend to say that IT is much more “touchy-feely” than networks where most of the Capex can be estimated almost mathematically (and sufficiently complicated for non-technology folks to not bother with it too much … btw I tend to disagree with this from a system or architecture perspective). Of course, that is also not the whole truth.
IT designs, plans, develops (or builds), and operates all the business support systems that enable the business to sell to its customers, support its customers, and in general, keep the relationship with the customer throughout the customer life-cycle across all the products and services offered by the business irrespective of it being fixed or mobile or converged. IT has much more intense interactions with the business than any other technology department, whose purpose is to support the business in enabling its requirements.
Most of the IT Capex is related to people’s work, such as development, maintenance, and operations. Thus capitalized labor of external and internal labor is the main driver for IT Capex. The work relates to maintaining and improving existing services and products and developing new ones on the IT system landscape or IT stacks. In 2021, Western European telco Capex spending was about 20% of their total revenue. Out of that, 4±1 % or in the order of 10±3 billion Euro is spent on IT. With ca. 714 million fixed and mobile subscribers, this corresponds to an IT average spend of 14 Euros per telco customer in 2021. Best investment practices should aim at an IT Capex spend at or below 3% of revenue on average over 5 years (to avoid penalizing IT transformation programs). As a rule of thumb, if you do not have any details of internal cost structure (I bet you usually would not have that information), assume that the IT-related Opex has a similar quantum as Capex (you may compensate for GDP differences between markets). Thus, the total IT spend (Capex and Opex) would be in the order of 2×Capex, so the IT Spend to Revenue double the IT-related Capex to Revenue. While these considerations would give you an idea of the IT investment level and drill down a bit further into cost structure details, it is wise to keep in mind that it’s all a macro average, and the spread can be pretty significant. For example, two telcos with roughly the same number of customers, IT landscape, and complexity and have pretty different revenue levels (e.g., due to differences in ARPU that can be achieved in the particular market) may have comparable absolute IT spending levels but very different relative levels compared to the revenue. I also know of telcos with very low total IT spend to Revenue ITR (shareholder imposed), which had (and have) a horrid IT infrastructure performance with very extended outages (days) on billing and frequent instabilities all over its IT systems. Whatever might have been saved by imposing a dramatic reduction in the IT Capex (e.g., remember 10 million euros Capex reduction equivalent to 200 million euros value enhancement) was more than lost on inferior customer service and experience (including the inability to bill the customers).
You will find industry experts and pundits that expertly insist that your IT development spend is way too high or too low (although the latter is rare!). I recommend respectfully taking such banter seriously. Although try to understand what they are comparing with, what KPIs they are using, and whether it’s apples for apples and not with pineapples. In my experience, I would expect a mobile-only business to have a better IT spend level than a fixed-mobile telco, as a mobile IT landscape tends to be more modern and relatively simple compared to a fixed IT landscape. First, we often find more legacy (and I mean with a capital L) in the fixed IT landscape with much older services and products still being kept operational. The fixed IT landscape is highly customized, making transformation and modernization complex and costly. At least if old and older legacy products must remain operational. Another false friend in comparing one company IT spending with another’s is that the cost structure may be different. For example, it is worth understanding where OSS (Operational Support System) development is accounted for. Is it in the IT spend, or is it in the Network-side of things? Service platforms and Data Centers may be another difference where such spending may be with IT or Networks.
Figure 24 shows the helicopter view of a traditional telco IT architectural stack. Unless the telco is a true greenfield, it is a very normal state of affairs to have multiple co-existing stacks, which may have some degree of integration at various levels (sub-layers). Most fixed-mobile telcos remain with a high degree of IT architecture separation between their mobile and fixed business on a retail and B2B level. When approaching IT, investments never consider just one year. Understand their IT investment strategy in the immediate past (2-3 years prior) as well as how that fits with known and immediate future investments (2 – 3 years out).
Above, Figure 24 illustrates the typical layers and sub-layers in an IT stack. Every sub-layer may contain different applications, functionalities, and systems, all with an over-arching property of the sub-layer description. It is not uncommon for a telco to have multiple IT stacks serving different brands (e.g., value, premium, …) and products (e.g., mobile, fixed, converged) and business lines (e.g., consumer/retail, business-to-business, wholesale, …). Some layers may be consolidated across stacks, and others may be more fragmented. The most common division is between fixed and mobile product categories, as historically, the IT business support systems (BSS) as well as the operational support systems (OSS) were segregated and might even have been managed by two different IT departments (that kind of silliness is more historical albeit recent).
Figure 25 shows a typical fixed-mobile incumbent (i.e., anything not greenfield) multi-stack IT architecture and their most likely aspiration of aggressive integrated stack supporting a fixed-mobile conversion business. Out of experience, I am not a big fan of retail & B2B IT stack integration. It creates a lot of operational complexity and muddies the investment transparency and economics of particular B2B at the expense of the retail business.
A typical IT landscape supporting fixed and mobile services may have quite a few IT stacks and a wide range of solutions for various products and services. It is not uncommon that a Fixed-Mobile telco would have several mobile brands (e.g., premium, value, …) and a separate (from an IT architecture perspective, at least) fixed brand. Then in addition, there may be differences between the retail (business-to-consumer, B2C) and the business-to-business (B2B) side of the telco, also being supported by separate stacks or different partitions of a stack. This is illustrated in Figure 24 above. In order for the telco business to become more efficient with respect to its IT landscape, including development, maintenance, and operational aspects of managing a complex IT infrastructure landscape, it should strive to consolidate stacks where it makes sense and not un-importantly along the business wish of convergence at least between fixed and mobile.
Figure 24 above illustrates an example of an IT stack harmonization activity long retail brands as well as Fixed and Mobile products as well as a separation of stacks into a retail and a business-to-business stack. It is, of course, possible to leverage some of the business logic and product synergies between B2C and B2B by harmonizing IT stacks across both business domains. However, in my experience, nothing great comes out of that, and more likely than not, you will penalize B2C by spending above and beyond value & investment attention on B2B. The B2B requirements tend to be significantly more complex to implement, their specifications change frequently (in line with their business customers’ demand), and the unit cost of development returns less unit revenue than the consumer part. Economically and from a value-consideration perspective, the telco needs to find an IT stack solution that is more in line with what B2B contributes to the valuation and fits its requirements. That may be a big challenge, particularly for minor players, as its business rarely justifies a standalone IT stack or developments. At least not a stack that is developed and maintained at the same high-quality level as a consumer stack. There is simply a mismatch in the B2B requirements, often having much higher quality and functionality requirements than the consumer part, and what it contributes to the business compared to, for example, B2C.
When I judge IT Capex, I care less about the absolute level of spend (within reason, of course) than what is practical to support within the given IT landscape the organization has been dealt with and, of course, the organization itself, including 3rd party support. Most systems will have development constraints and a natural order of how development can be executed. It will not matter how much money you are given or how many resources you throw at some problems; there will be an optimum amount of resources and time required to complete a task. This naturally leads to prioritization which may lead to disappointment of some stakeholders and projects that may not be prioritized to the degree they might feel entitled to.
When looking at IT capital spending and comparing one telco with another, it is worthwhile to take a 3- to 5-year time horizon, as telcos may be in different business and transformation cycles. A one-year comparison or benchmark may not be appropriate for understanding a given IT-spend journey and its operational and strategic rationale. Search for incidents (frequency and severity) that may indicate inappropriate spend prioritization or overall too little available IT budget.
The IT Capex budget would typically be split into (a) Consumer or retail part (i.e., B2C), (b) Business to Business and wholesale part, (c) IT technical part (optimization, modernization, cloudification, and transformations in general), and a (d) General and Administrative (G&A) part (e.g., Finance, HR, ..). Many IT-related projects, particularly of transformative nature, will run over multiple years (although if much more than 24 months, the risk of failure and monetary waste increases rapidly) and should be planned accordingly. For the business-driven demand (from the consumer, business, and wholesale), it makes sense to assign Capex proportional to the segment’s revenue and the customers those segments support and leverage any synergies in the development work required by the business units. For IT, capital spending should be assigned, ensuring that technical debt is manageable across the IT infrastructure and landscape and that efficiency gains arising from transformative projects (including landscape modernization) are delivered timely. In general, such IT projects promise efficiency in terms of more agile development possibilities (faster time to market), lower development and operational costs, and, last but not least, improved quality in terms of stability and reduced incidents. The G&A prioritizes finance projects and then HR and other corporate projects.
In summary, the following topics would likely be on the Capex priority list;
Provide IT development support for business demand in the next business plan cycle (3 – 5 years with a strong emphasis on the year ahead). The allocation key should be close to the Revenue (or Ebitda) and customer contribution expected within the budget planning period. The development focus is on maintenance, (incremental) improvements to existing products/services, and new products/services required to make the business plans. In my experience, the initial demand tends to be 2 to 3 times higher than what a reasonable financial envelope would dictate (i.e., even considering what is possible to do within the natural limitations of the given IT landscape and organization) and what is ultimately agreed upon.
Cloudification transformation journey moving away from the traditional monolithic IT platform and into a public, hybrid, or private cloud environment. In my opinion, the safest approach is a “lift-and-shift” approach where existing functionality is developed in the cloud environment. After a successful migration from the traditional monolithic platform into the cloud environment, the next phase of the cloudification journey will be to move to a cloud-native framework should be embarked. This provides a very solid automation framework delivering additional efficiencies and improved stability and quality (e.g., reduction in incidents). Analysts should be aware that migrating to a (public) cloud environment may reduce the capitalization possibilities with the consequence that Capex may reduce in the forward budget planning, but this would be at the expense of increased Opex for the IT organization.
Stack consolidation. Reducing the number of IT stacks generally lowers the IT Capex demand and improves development efficiency, stability, and quality. The trend is to focus on the harmonization efforts on the frontend (Portals and Outlets layer in Figure 14), the CRM layer (retiring legacy or older CRM solutions), and moving down the layers of the IT stack (see Figure 14) often touching the complex backend systems when they become obsolete providing an opportunity to migrate to a modern cloud-based solution (e.g., cloud billing).
Modernization activities are not covered by cloudification investments or business requirements.
Development support for Finance (e.g., ERP/SAP requirements), HR requirements, and other miscellaneous activities not captured above.
Chinese suppliers are rarely an issue in Western European telecom’s IT landscape. However, if present in a telco’s IT environment, I would expect Capex has been allocated for phasing out that supplier urgently over the next 24 months (pending the complexity of such a transformation/migration program) due to strong political and regulatory pressures. Such an initiative may have a value-destructing impact as business-driven IT development (related to the specific system) might not be prioritized too highly during such a program and thus result in less ability to compete for the telco during a phase-out program.
IT Capex KPIs: IT share of Total Capex (if available, broken down into a Fixed and Mobile part),IT Capex to Revenue, ITR (IT total spend to Revenue), IT Capex per Customer, IT Capex per Employee, IT FTEs to Total FTEs.
Moreover, if available or being modeled, I would like to have an idea about how much of the IT Capex goes to investment categories such as (i) Maintain, (ii) Growth, and (iii) Transform. I will get worried if the majority of IT Capex over an extended period goes to the Growth category and little to Maintain and Transform. This indicates a telco that has deprioritized quality and ignores efficiency, resulting in the risk of value destruction over time (if such a trend were sustained). A telco with little Transform spend (again over an extended period) is a business that does not modernize (another word for sweating assets).
Capex modeling comment: when I am modeling IT and have little information available, I would first assume an IT Capex to Revenue ratio around 4% (mobile-only) to 6% (fixed-mobile operation) and check as I develop the other telco Capex components whether the IT Capex stays within 15% to 25%. Of course, keep an eye out for all the above IT Capex KPIs, as they provide a more holistic picture of how much confidence you can have in the Capex model.
Figure 26 illustrates the anticipated IT Capex to Revenue ranges for 2024: using New Street Research (total) Capex data for Western Europe, the author’s own Capex projection modeling, and using the heuristics that IT spend typically would be 15% to 25% of the total Capex, we can estimate the most likely ranges of IT Capex to Revenue for the telecommunications business covered by NSR for 2024. For individual operations, we may also want to look at the time series of IT spending to revenue and compare that to any available intelligence (e.g., transformation intensive, M&A integration, business-as-usual, etc..)
Using the heuristic of the IT Capex being between 15% (1st quantile) and 25% (3rd quantile) of the total Capex, we can get an impression of how much individual Telcos invest in IT annually. The above chart shows such an estimate for 2024. I have the historical IT spending levels for several Western European Telcos, which agree well with the above and would typically be a bit below the median unless a Telco is in the progress of a major IT transformation (e.g., after a merger, structural separation, Huawei forced replacement, etc..). One would also expect and should check that the total IT spend, Capex and Opex, are decreasing over time when the transformational IT spend has been removed. If this is observed, it would indicate that Telco does become increasingly more efficient in its IT operation. Usually, the biggest effect should be in IT Opex reduction over time.
Figure 27 illustrates the anticipated IT Capex to Customer ranges for 2024: having estimated the likely IT spend ranges (in Figure 26) for various Western European telcos, allows us to estimate the expected 2024 IT spend per customer (using New Street Research data, author’s own Capex projection model and the IT heuristics describe in the section). In general and in the absence of structural IT transformation programs, I would expect the IT per customer spend to be below the median. Some notes to the above results: TDC (Nuuday & TDC Net) has major IT transformation programs ongoing after the structural separation, KPN is in progress with replacing their Huawei BSS, and I would expect them to be at the upper part of IT spending, Telenor Norway seems higher than I would expect but is an incumbent that traditionally spends substantially more than its competitors so might be okay but caution should be taken here, Switzerland in general and Swisscom, in particular, is higher than I would have expected. This said, it is a sophisticated Telco services market that would be likely to spend above the European average, irrespective I would take some caution with the above representation for Switzerland & Swisscom.
Similar to the IT Capex to Revenue, we can get an impression of what Telcos spend on IT Capex as it relates to their total mobile and fixed customer base. Again for Telcos in Western Europe (as well as outside), these ranges shown above do seem reasonable as the estimated range of where one would expect the IT spend. The analyst is always encouraged to look at this over a 3- to 5-year period to better appreciate the trend and should keep in mind that not all Telcos are in synch with their IT investments (as hopefully is obvious as transformation strategies and business cycles may be very different even within the same market).
Other, or miscellaneous, investments tend to be between 3% and 8% of the Telecom Capex.
When modeling a telco’s Capex, I find it very helpful to keep an “Other” or “Miscellaneous” Capex category for anything non-technology related. Modeling-wise, having a placeholder for items you don’t know about or may have forgotten is convenient. I typically start my models with 15% of all Capex. As my model matures, I should be able to reduce this to below 10% and preferably down to 5% (but I will accept 8% as a kind of good enough limit). I have had Capx review assignments where the Capex for future years had close to 20% in the “Miscellaneous.” If this “unspecified” Capex would not be included, the Capex to Revenue in the later years would drop substantially to a level that might not be deemed credible. In my experience, every planned Capex category will have a bit of “Other”-ness included as many smaller things require Capex but are difficult to mathematically derive a measure for. I tend to leave it if it is below 5% of a given Capex category. However, if it is substantial (>5%), it may reveal “sandbagging” or simply less maturity in the Capex planning and budget process.
Apart from a placeholder for stuff we don’t know, you will typically find Capex for shop refurbishment or modernization here, including office improvements and IT investments.
DE-AVERAGING THE TELECOM CAPEX TO FIXED AND MOBILE CONTRIBUTIONS.
There are similar heuristics to go deeper down into where the Capex should be spent, but that is a detail for another time.
Our first step is decomposing the total Capex into a fixed and a mobile component. We find that a multi-linear model including Total Capex, Mobile Customers, Mobile Service Revenue, Fixed Customers, and Fixed Service Revenues can account for 93% of the Capex trend. The multi-linear regression formula looks like the following;
with C = Capex, N = total customer count, R = service revenue, and α and β are the regression coefficient estimates from the multi-linear regression. The Capex model has been trained on 80% of the data (1,008 data points) chosen randomly and validated on the remainder (252 data points). All regression coefficients (4 in total) are statistically significant, with p-values well below a 95% confidence level.
Figure 28 above shows the Predicted Capex versus the Actual Capex. It illustrates that the predicted model agreed reasonably well with the actual Capex, which would also be expected based on the statistical KPIs resulting from the fit.
The Total is (obviously) available to us and therefore allows us to estimate both fixed and mobile Capex levels, by
The result of the fixed-mobile Capex decomposition is shown in Figure 26 below. Apart from being (reasonably) statistically sound, it is comforting that the trend in Capex for fixed and mobile seem to agree with what our intuition should be. The increase in mobile Capex (for Western Europe) over the last 5 years appears reasonable, given that 5G deployment commenced in early 2019. During the Covid lockdown from early 2020, fixed revenue was boosted by a massive shift in fixed broadband traffic (and voice) from the office to the individuals’ homes. Likewise, mobile service revenues have been in slow decline for years. Thus, the Capex increase due to 5G and reduced mobile service revenues ultimately leads to a relatively more significant increase in the mobile Capex to Revenue ratio.
Figure 29 illustrates the statistical modeling (by multi-linear regression), or decomposition, of the Total Capex as a function of Mobile Customers, Mobile Service Revenues, Fixed Customers, and Fixed Service Revenues, allowing to break up of the Capex into Fixed and Mobile components by decomposing the total Capex. The absolute Capex level is higher for fixed than what is found for mobile, with about a factor of 2 until 2021, when mobile Capex increases due to 5G investments in the mobile industry. It is found that the Mobile Capex has increased the most over the last 5 years (e.g., 5G deployment) while the service revenues have declined somewhat over the same period. This increased the Mobile Capex to Service Revenue ratio (note: based on Total Revenue, the ratio would be somewhat smaller, by ca. 17%). Source: Total Capex, Fixed, and Mobile Service revenues from New Street Research data for Western Europe. Note: The decomposition of the total Capex into Fixed and Mobile Capex is based on the author’s own statistical analysis and modeling. It is not a delivery of the New Street Research report.
CAN MOBILE-TRAFFIC GROWTH CONTINUE TO BE ACCOMMODATED CAPEX-WISE?
In my opinion, there has been much panic in our industry in the past about exhausting the cellular capacity of mobile networks and the imminent doom of our industry. A fear fueled by the exponential growth of user demand perceived inadequate spectrum amount and low spectral efficiency of the deployed cellular technologies, e.g., 3G-HSPA, classical passive single-in single-out antennas. Going back to the “hey-days” of 3G-HSPA, there was a fear that if cellular demand kept its growth rate, it would result in supply requirements going towards infinity and the required Capex likewise. So clearly an unsustainable business model for the mobile industry. Today, there is (in my opinion) no basis for such fears short or medium-term. With the increased fiberization of our society, where most homes will be connected to fiber within the next 5 – 10 years, cellular doomsday, in the sense of running out of capacity or needing infinite levels of Capex to sustain cellular demand, maybe a day never to come.
In Western Europe, the total mobile subscriber penetration was ca. 130% of the total population in 2021, with an excess of approximately 2.1+ mobile devices per subscriber. Mobile internet penetration was 76% of the total population in 2021 and is expected to reach 83% by 2025. In 2021, Europe’s average smartphone penetration rate was 77.6%, and it is projected to be around 84% by 2025. Also, by 2024±1, 50% of all connections in Western Europe are projected to be 5G connections. There are some expectations that around 2030, 6G might start being introduced in Western European markets. 2G and 3G will be increasingly phased out of the Western European mobile networks, and the spectrum will be repurposed for 4G and eventually 5G.
The above Figure 30 shows forecasted mobile users by their main mobile access technology. Source: based on the author’s forecast model relying on past technology diffusion trends for Western Europe and benchmarked against some WEU markets and other telco projections. See also 5G Standalone – European Demand & Expectations by Kim Larsen.
We may not see a complete phase-out of either older Gs, as observed in Figure 19. Due to a relatively large base of non-VOLTE (Voice-over-LTE) devices, mobile networks will have to support voice circuit-switched fallback to 2G or 3G. Furthermore, for the foreseeable future, it would be unlikely that all visiting roaming customers would have VOLTE-based devices. Furthermore, there might be legacy machine-2-machine businesses that would be prohibitively costly and complex to migrate from existing 2G or 3G networks to either LTE or 5G. All in all, ensure that 2G and 3G may remain with us for reasonably long.
Figure 31 above shows that mobile and fixed data traffic consumption is growing in totality and per-user level. On average mobile traffic grew faster than fixed from 2015 to 2021. A trend that is expected to continue with the introduction of 5G. Although the total traffic growth rate is slowing down somewhat over the period, on a per-user basis (mobile as well as fixed), the consumptive growth rate has remained stable.
Since the early days of 3G-HSPA (High-Speed Packet Access) radio access, investors and telco businesses have been worried that there would be an end to how much demand could be supported in our cellular networks. The “fear” is often triggered by seeing the exponential growth trend of total traffic or of the usage per customer (to be honest, that fear has not been made smaller by technology folks “panicking” as well).
Let us look at the numbers for 2021 as they are reported in the Cisco VNI report. The total mobile data traffic was in the order of 4 Exabytes (4 Billion gigabytes, GB), more than 5.5× the level of 2016. It is more than 600 million times the average mobile data consumption of 6.5 GB per month per customer (in 2021). Compare this with the Western European population of ca. 200 million. While big numbers, the 6.5 GB per month per customer is insignificant. Assuming that most of this volume comes from video streaming at an optimum speed of 3 – 5 Mbps (good enough for HD video stream), the 6.5 GB translates into approx. 3 – 5 hours of video streaming over a month.
The above Figure 32 Illustrates a 24-hour workday total data demand on the mobile network infrastructure. A weekend profile would be more flattish. We spend at least 12 hours in our home, ca. 7 hours at work (including school), and a maximum of 5 hours (~20%) commuting, shopping, and otherwise being away from our home or workplace. Previous studies of mobile traffic load have shown that 80% of a consumer’s mobile demand falls in 3 main radio node sites around the home and workplace. The remaining 20% tends to be much more mobile-like in the sense of being spread out over many different radio-node sites.
Daily we have an average of ca. 215 Megabytes per day (if spread equally over the month), corresponding to 6 – 10 minutes of video streaming. The average length of a YouTube was ca. 4.4 minutes. In Western Europe, consumers spend an average of 2.4 hours per day on the internet with their smartphones (having younger children, I am surprised it is not more than that). However, these 2.4 hours are not necessarily network-active in the sense of continuously demanding network resources. In fact, most consumers will be active somewhere between 8:00 to around 22:00, after which network demand reduces sharply. Thus, we have 14 hours of user busy time, and within this time, a Western European consumer would spend 2.4 hours cumulated over the day (or ca. 17% of the active time).
Figure 33 above illustrates (based on actual observed trends) how 5 million mobile users distribute across a mobile network of 5,000 sites (or radio nodes) and 15,000 sectors (typically 3 sectors = 1 site). Typically, user and traffic distributions tend to be log-norm-like with long tails. In the example above, we have in the busy hour a median value of ca. 80 users attached to a sector, with 15 being active (i.e., loading the network) in the busy hour, demanding a maximum of ca. 5 GB (per sector) or an average of ca. 330 MB per active user in the radio sector over that sector’s relevant busy hour.
Typically, 2 limits, with a high degree of inter-dependency, would allegedly hit the cellular businesses rendering profitable growth difficult at some point in the future. The first limit is a practical technology limit on how much capacity a radio access system can supply. As we will see a bit later, this will depend on the operator’s frequency spectrum position (deployed, not what might be on the shelf), the number of sites (site density), the installed antenna technology, and its effective spectral efficiency. The second (inter-dependent) limit is an economic limit. The incremental Capex that telcos would need to commit to sustaining the demand at a given quality level would become highly unprofitable, rendering further cellular business uneconomical.
From a Capex perspective, the cellular access part drives a considerable amount of the mobile investment demand. Together with the supporting transport, such as fronthaul, backhaul, aggregation, and core transport, the capital investment share is typically 50% or higher. This is without including the spectrum frequencies required to offer the cellular service. Such are usually acquired by local frequency spectrum auctions and amount to substantial investment levels.
In the following, the focus will be on cellular access.
The Cellular Demand.
Before discussing the cellular supply side of things, let us first explore the demand side from the view of a helicopter. Demand is created by users (N) of the cellular services offered by telcos. Users can be human or non-human such as things in general or more specific machines. Each user has a particular demand that, in an aggregated way, can be represented by the average demand in Bytes per User (d). Thus, we can then identify two growth drivers. One from adding new users (ΔN) to our cellular network and another from the incremental change in demand per user (ΔN) as time goes by.
It should be noted that the incremental change in demand or users might not per se be a net increase. Still, it could also be a net decrease, either because the cellular networks have reached the maximum possible level of capacity (or quality) that results in users either reducing their demand or “ churning” from those networks or that an alternative to today’s commercial cellular network triggers abandonment as high-demand users migrate to that alternative — leading both to a reduction in cellular users and the average demand per user. For example, a near-100% Fiber-to-the-Home coverage with supporting WiFi could be a reason for users to abandon cellular networks, at least in an indoor environment, which would reduce between 60 to 80% of present-day cellular data demand. This last (hypothetical) is not an issue for today’s cellular networks and telco businesses.
Of course, this can easily be broken down into many more drivers and details, e.g., technology diffusion or adaptation, the rate of users moving from one access technology to another (e.g., 3G→4G, 4G→5G, 5G→FTTH+WiFi), improved network & user device capabilities (better coverage, higher speeds, lower latency, bigger display size, device chip generation), new cellular service adaptation (e.g., TV streaming, VR, AR, …), etc.…
However, what is often forgotten is that the data volume of consumptive demand (in Byte) is not the main direct driver for network demand and, thus, not for the required investment level. A gross volumetric demand can be caused by various gross throughput demands (bits per second). The throughput demanded in the busiest hour ( or ) is the direct driver of network load, and thus, network investments, the volumetric demand, is a manifestation of that throughput demand.
With being the number of active users in a given radio cell at the time-instant of unit t taken within a day. is the Bytes consumed in a time instant (e.g., typically a second); thus, 8 gives us the bits per time unit (or bits/sec), which is throughput consumed. Sum over all the cells’ instant throughput ( bits/sec) in the same instant and take the maximum across. For example, a day provides the busiest hour throughput for the whole network. Each radio cell drives its capacity provision and supply (in bits/sec) and the investments required to provide that demanded capacity in the air interface and front- and back-haul.
For example, if n = 6 active (concurrent) users, each consuming on average = 0.625 Mega Bytes per second (5 Megabits per second, Mbps), the typical requirement for a YouTube stream with an HD 1080p resolution, our radio access network in that cell would experience a demanded load of 30 Mbps (i.e., 6×5 Mbps). Of course, provided that the given cell has sufficient capacity to deliver what is demanded. A 4G cellular system, without any special antenna technology, e.g., Single-in-Single-out (SiSo) classical antenna and not the more modern Multiple-in-Multiple-out (MiMo) antenna, can be expected to deliver ca. 1.5 Mbps/MHz per cell. Thus, we would need at least 20 MHz spectrum to provide for 6 concurrent users, each demanding 5 Mbps. With a simple 2T2R MiMo antenna system, we could support about 8 simultaneous users under the same conditions. A 33% increase in what our system can handle without such an antenna. As mobile operators implement increasingly sophisticated antenna systems (i.e., higher-order MiMo systems) and move to 5G, a leapfrog in the handling capacity and quality will occur.
Figure 34 Is the sky the limit to demand? Ultimately, the limit will come from the practical and economic limits to how much can be supplied at the cellular level (e.g., spectral bandwidth, antenna technology, and software features …). Quality will reduce as the supply limit is reached, resulting in demand adaptation, hopefully settling at a demand-supply (metastable) equilibrium.
Cellular planners have many heuristics to work with that together trigger when a given radio cell would be required to be expanded to provide more capacity, which can be provided by software (licenses), hardware (expansion/replacement), civil works (sectorization/cell splits) and geographical (cell split) means. Going northbound, up from the edge of the radio network up through the transmission chain, such as fronthaul, back, aggregation, and core transport network, may require additional investments in expanding the supplied demand at a given load level.
As discussed, mobile access and transport together can easily make up more than half of a mobile capital budget’s planned and budgeted Capex.
So, to know whether the demand triggers new expansions and thus capital demand as well as the resulting operational expenses (Opex), we really need to look at the supply side. That is what our current mobile network can offer. When it cannot provide a targeted level of quality, how much capacity do we have to add to the network to be on a given level of service quality?
The Cellular Supply.
Cellular capacity in units of throughput () given in bits per second, the basic building block of quality, is relatively easy to estimate. The cellular throughput (per unit cell) is provided by the amount of committed frequency spectrum to the air interface, what your radio access network and antenna support are, multiplied by the so-called spectral efficiency in bits per Hz per cell. The spectral efficiency depends on the antenna technology and the underlying software implementation of signal processing schemes enabling the details of receiving and sending signals over the air interface.
can be written as follows;
With Mbps being megabits (a million bits) per second and MHz being Mega Herz.
For example, if we have a site that covers 3 cells (or sectors) with a deployed 100 MHz @ 3.6GHz (B) on a 32T32R advanced antenna system (AAS) with an effective downlink (i.e., from the antenna to user), spectral efficiency of ca. 20 Mbps/MHz/cell (i.e., ), we should expect to have a cell throughput on average at 1,000 Mbps (1 Gbps).
The capacity supply formula can be applied to the cell-level consideration providing sizing and thus investment guidance as we move northbound up the mobile network and traffic aggregates and concentrates towards the core and connections points to the external internet.
From the demand planning (e.g., number of customers, types of services sold, etc..), that would typically come from the Marketing and Sales department within the telco company, the technical team can translate those plans into a network demand and then calculate what they would need to do to cope with the customer demand within an agreed level of quality.
In Figure 35 above, operators provide cellular capacity by deploying their spectral assets on an appropriate antenna type and system-level radio access network hardware and software. Competition can arise from a superior spectrum position (balanced across low, medium, and high-frequency bands), better or more aggressive antenna technology, and utilizing their radio access supplier(s)’ features (e.g., signal processing schemes). Usually, the least economical option will be densifying the operator’s site grid where needed (on a macro or micro level).
Figure 36 above shows the various options available to the operator to create more capacity and quality. In terms of competitive edge, more spectrum than competitors provided it is being used and is balanced across low, medium, and high bands, provides the surest path to becoming the best network in a given market and is difficult to economically copy by operators with substantially less spectrum. Their options would be compensating for the spectrum deficit by building more sites and deploying more aggressive antenna technologies. The last one is relatively easy to follow by anyone and may only provide some respite temporarily.
An average mobile network in Western Europe has ca. 270 MHz spectrum (60 MHz low-band below 1800 and 210 MHz medium-band below 5 GHz) distributed over an average of 7 cellular frequency bands. It is rare to see all bands deployed in actual deployments and not uniformly across a complete network. The amount of spectrum deployed should match demand density; thus, more spectrum is typically deployed in urban areas than in rural ones. In demand-first-driven strategies, the frequency bands will be deployed based on actual demand that would typically not require all bands to be deployed. This is opposed to MNOs that focus on high quality, where demand is less important, and where typically, most bands would be deployed extensively across their networks. The demand-first-driven strategy tends to be the most economically efficient strategy as long as the resulting cellular quality is market-competitive and customers are sufficiently satisfied.
In terms of downlink spectral capacity, we have an average of 155 MHz or 63 MHz, excluding the C-band contribution. Overall, this allows for a downlink supply of a minimum of 40 GB per hour (assuming low effective spectral efficiency, little advanced antenna technology deployed, and not all medium-band being utilized, e.g., C-Band and 2.5 GHz). Out of the 210 MHz mid-band spectrum, 92 MHz falls in the 3.X GHz (C-band) range and is thus still very much in the process of being deployed for 5G (as of June 2022). The C-band has, on average, increased the spectral capacity of Western European telcos by 50+% and, with its very high suitability for deployment together with massive MiMo and advanced antenna systems, effectively more than doubled the total cellular capacity and quality compared to pre-C-band deployment (using a 64T64R massive MiMo as a reference with today’s effective spectral efficiency … it will be even better as time goes by).
Figure 37 (above) shows the latest Ookla and OpenSignal DL speed benchmarks for Western Europe MNOs (light blue circles), and comparing this with their spectrum holdings below 3.x GHz indicates that there may be a lot of unexploited cellular capacity and quality to be unleashed in the future. Although, it would not be for free and likely require substantial additional Capex if deemed necessary. The ‘Expected DL Mbps’ (orange solid line, *) assumes the simplest antenna setup (e.g., classical SiSo antennas) and that all bands are fully used. On average, MNOs above the benchmark line have more advanced antenna setups (higher-order antennas) and fully (or close to) spectrum deployment. MNOs below the benchmark line likely have spectrum assets that have not been fully deployed yet and (or) “under-prioritized” their antenna technology infrastructure. The DL spectrum holding excludes C- and mmWave spectrum. Note: There was a mistake in the original chart published on LinkedIn as the data was depicted against the total spectrum holding (DL+UL) and not only DL. Data: 54 Western European telcos.
Figure 37 illustrates the Western European cellular performance across MNOs, as measured by DL speed in Mbps, and compares this with the theoretical estimate of the performance they could have if all DL spectrum (not considering C-band, 3.x GHz) in their portfolio had been deployed at a fairly simple antenna setup (mainly SiSo and some 2T2R MiMo) with an effective spectral efficiency of 0.85 Mbps per MHz. It is good to point out that this is expected of 3G HSPA without MiMo. We observe that 21 telcos are above the solid (orange) line, and 33 have an actual average measured performance that is substantially below the line in many cases. Being above the line indicates that most spectrum has been deployed consistently across the network, and more advanced antennas, e.g., higher-order MiMo, are in use. Being below the line does (of course) not mean that networks are badly planned or not appropriately optimized. Not at all. Choices are always made in designing a cellular network. Often dictated by the economic reality of a given operator, geographical demand distribution, clutter particularities, or the modernization cycle an operator may be in. The most obvious reasons for why some networks are operating well under the solid line are; (1) Not all spectrum is being used everywhere (less in rural and more in urban clutter), (2) Rural configurations are simpler and thus provide less performance than urban sites. We have (in general) more traffic demand in urban areas than in rural. Unless a rural area turns seasonally touristic, e.g., lake Balaton in Hungary in the summer … It is simply a good technology planning methodology to prioritize demand in Capex planning, and it makes very good economic sense (3) Many incumbent mobile networks have a fundamental grid based on (GSM) 900MHz and later in-filled for (UMTS) 2100MHz…which typically would have less site density than networks based on (DCS) 1800MHz. However, site density differences between competing networks have been increasingly leveled out and are no longer a big issue in Western Europe (at least).
Overall, I see this as excellent news. For most mobile operators, the spectrum portfolio and the available spectrum bandwidth are not limiting factors in coping with demanded capacity and quality. Operators have many network & technology levers to work with to increase both quality and capacity for their customers. Of course, subject to a willingness to prioritize their Capex accordingly.
A mobile operator has few options to supply cellular capacity and quality demanded by its customer base.
Acquire more spectrum bandwidth by buying in an auction, buying from 3rd party (including M&A), asymmetric sharing, leasing, or trading (if regulatory permissible).
Deploy a better (spectral efficient) radio access technology, e.g., (2G, 3G) → (4G, 5G) or/and 4G → 5G, etc. Benefits will only be seen once a critical mass of customer terminal equipment supporting that new technology has been reached on the network (e.g., ≥20%).
Upgrade antenna technology infrastructure from lower-order passive antennas to higher-order active antenna systems. In the same category would be to ensure that smart, efficient signal processing schemes are being used on the air interface.
Building a denser cellular network where capacity demand dictates or coverage does not support the optimum use of higher frequency bands (e.g., 3.x GHz or higher).
Small cell deployment in areas where macro-cellular built-out is no longer possible or prohibitively costly. Though small cells scale poorly with respect to economics and maybe really the last resort.
Sectorization with higher-frequency massive-MiMo may be an alternative to small-cell and macro-cellular additions. However, sectorization requires that it is possible civil-engineering wise (e.g., construction) re: structural stability, permissible by the landlord/towerco and finally economic compared to a new site built. Adding more than the usual 3-sectors to a site would further boost site spectral efficiency as more antennas are added.
Acquiring more spectrum requires that such spectrum is available either by a regulatory offering (public auction, public beauty contest) or via alternative means such as 3rd party trading, leasing, asymmetric sharing, or by acquiring an MNO (in the market) with spectrum. In Western Europe, the average cost of spectrum is in the ballpark of 100 million Euro per 10 million population per 20 MHz low-band or 100 MHz medium bands. Within the European Union, recent auctions provide a 20-year usage-rights period before the spectrum would have to be re-auctioned. This policy is very different from, for example, in the USA, where spectrum rights are bought and ownership secured in perpetuity (sometimes conditioned on certain conditions being met). For Western Europe, apart from the mmWave spectrum, in the foreseeable future, there will not be many new spectrum acquisition opportunities in the public domain.
This leaves mobile operators with other options listed above. Re-farming spectrum away from legacy technology (e.g., 2G or 3G) in support of another more spectral efficient access technology (e.g., 4G and 5G) is possibly the most straightforward choice. In general, it is the least costly choice provided that more modern options can support the very few customers left. For either retiring 2G or 3G, operators need to be aware that as long as not all terminal equipment support Voice-over-LTE (VoLTE), they need to keep either 2G or 3G (but not both) for 4G circuit-switched fallback (to 2G or 3G) for legacy voice services. The technologist should be prepared for substantial pushback from the retail and wholesale business, as closing down a legacy technology may lead to significant churn in that legacy customer base. Although, in absolute terms, the churn exposure should be much smaller than the overall customer base. Otherwise, it will not make sense to retire the legacy technology in the first place. Suppose the spectral re-farming is towards a new technology (e.g., 5G). In that case, immediate benefits may not occur before a critical mass of capable devices is making use of the re-farmed spectrum. The Capex impact of spectral re-farming tends to be minor, with possibly some licensing costs associated with net savings from retiring the legacy. Most radio departments within mobile operators, supplier experts, and managed service providers have gained much experience in this area over the last 5 – 7 years.
Another venue that should be taken is upgrading or modernizing the radio access network with more capable antenna infrastructure, such as higher-order massive MiMo antenna systems. As has been pointed out by Prof. Emil Björnson also, the available signal processing schemes (e.g., for channel estimation, pre-coding, and combining) will be essential for the ultimate gain that can be achieved. This will result in a leapfrog increase in spectral efficiency. Thus, directly boosting air-interface capacity and the quality that the mobile customer can enjoy. If we take a 20-year period, this activity is likely to result in a capital demand in the order of 100 million euros for every 1,000 sites being modernized and assumes a modernization (or obsolescence) cycle of 7 years. In other words, within the next 20 years, a mobile operator will have undergone at least 3 antenna-system modernization cycles. It is important to emphasize that this does not (entirely) cover the likely introduction of 6G during the 20 years. Operators face two main risks in their investment strategy. One risk is that they take a short-term look at their capital investments and customer demand projections. As a result, they may invest in insufficient infrastructure solutions to meet future demands, forcing accelerated write-offs and re-investments. The second significant risk is that the operator invests too aggressively upfront in what appears to be the best solution today to find substantially better and more efficient solutions in the near future that more cautious competitive operators could deploy and achieve a substantially higher quality and investment efficiency. Given the lack of technology maturity and the very high pace of innovation in advanced antenna systems, the right timing is crucial but not straightforward.
Last and maybe least, the operator can choose to densify its cellular grid by adding one or more macro-cellular sites or adding small cells across existing macro-cellular coverage. Before it is possible to build a new site or site, the operator or the serving towerco would need to identify suitable locations and subsequently obtain a permit to establish the new site or site. In urban areas, which typically have the highest macro-site densities, getting a new permit may be very time-consuming and with a relatively high likelihood of not being granted by the municipality. Small cells may be easier to deploy in urban environments than in macro sites. For operators making use of towerco to provide the passive site infrastructure, the cost of permitting and building the site and materials (e.g., steel and concrete) is a recurring operational expense rather than a Capex charge. Of course, active equipment remains a Capex item for the relevant mobile operator.
The conclusion I make above is largely consistent with the conclusions made by New Street Research in their piece “European 5G deep-dive” (July 2021). There is plenty of unexploited spectrum with the European operators and even more opportunity to migrate to more capable antenna systems, such as massive-MiMo and active advanced antenna systems. There are also above 3GHz, other spectrum opportunities without having to think about millimeter Wave spectrum and 5G deployment in the high-frequency spectrum range.
I greatly acknowledge my wife Eva Varadi, for her support, patience, and understanding during the creative process of writing this Blog. There should be no doubt that without the support of Russell Waller (New Street Research), this blog would not have been possible. Thank you so much for providing much of the data that lays the ground for much of the Capex analysis in this article. Of course, a lot of thanks go out to my former Technology and Network Economics colleagues, who have been a source of inspiration and knowledge. I cannot get away with acknowledging Maurice Ketel (who for many years let my Technology Economics Unit in Deutsche Telekom, I respect him above and beyond), Paul Borker, David Haszeldine, Remek Prokopiak, Michael Dueser, Gudrun Bobzin, as well as many, many other industry colleagues who have contributed with valuable insights, discussions & comments throughout the years. Many thanks to Paul Zwaan for a lot of inspiration, insights, and discussions around IT Architecture.
Without executive leadership’s belief in the importance of high-quality techno-financial models, I have no doubt that I would not have been able to build up the experience I have in this field. I am forever thankful, for the trust and for making my professional life super interesting and not just a little fun, to Mads Rasmussen, Bruno Jacobfeuerborn, Hamid Akhavan, Jim Burke, Joachim Horn, and last but certainly not least, Thorsten Langheim.
Kim Kyllesbech Larsen, “The Nature of Telecom Capex.” (July, 2022). My first article laying the ground for Capex in the Telecom industry. The data presented in this article is largely outdated and remains for comparative reasons.
Tom Copeland, Tim Koller, and Jack Murrin, “Valuation”, John Wiley & Sons, (2000). I regard this as my “bible” when it comes to understanding enterprise valuation. There are obviously many finance books on valuation (I have 10 on my bookshelf). Copeland’s book is the best imo.
Stefan Rommer, Peter Hedman, Magnus Olsson, Lars Frid, Shabnam Sultana, and Catherine Mulligan, “5G Core Networks”, Academic Press, (2020, 1st edition). Good account for what a 5G Core Network entails.
Jia Shen, Zhongda Du, Zhi Zhang, Ning Yang and Hai Tang, “5G NR and enhancements”, Elsevier (2022, 1st edition). Very good and solid account of what 5G New Radio (NR) is about and the considerations around it.
Wim Rouwet, “Open Radio Access Network (O-RAN) Systems Architecture and Design”, Academic Press, (2022). One of the best books on Open Radio Access Network architecture and design (honestly, there are not that many books on this topic yet). I like that the author, at least as an introduction makes the material reasonably accessible to even non-experts (which tbh is also badly needed).
Strand Consult, “OpenRAN and Security: A Literature Review”, (June, 2022). Excellent insights into the O-RAN maturity challenges. This report focuses on the many issues around open source software-based development that is a major part of O-RAN and some deep concerns around what that may mean for security if what should be regarded as critical infrastructure. I warmly recommend their “Debunking 25 Myths of OpenRAN”.
Hwaiyu Geng P.E., “Data Center Handbook”, Wiley (2021, 2nd edition). I have several older books on the topic that I have used for my models. This one brings the topic of data center design up to date. Also includes the topic of Cloud and Edge computing. Good part on Data Center financial analysis.
James Farmer, Brian Lane, Kevin Bourgm Weyl Wang, “FTTx Networks, Technology Implementation, and Operations”, Elsevier, (2017, 1st edition). It has some books covering FTTx deployment, GPON, and other alternative fiber technologies. I like this one in particular as it covers hands-on topics as well as basic technology foundations.
New Street Research, “European 5G deep-dive”, (July, 2021).
Prof. Emil Björnson, https://ebjornson.com/research/ and references therein. Please take a look at many of Prof. Björnson video presentations (e.g., many brilliant YouTube presentations that are fairly assessable).
This week (Week 17, 2023), I submitted my comments and advice titled “Development of a National Spectrum Strategy (NSS)” to the United States National Telecommunications & Information Administration (NTIA) related to their work on a new National Spectrum Strategy.
Of course, one might ask why, as a European, bother with the spectrum policy of the United States. So hereby, a bit of reasoning for bothering with this super interesting and challenging topic of spectrum policy on the other side of the pond.
A EUROPEAN IN AMERICA.
As a European coming to America (i.e., USA) for the first time to discuss the electromagnetic spectrum of the kind mobile operators love to have exclusive access to, you quickly realize that Europe’s spectrum policy/policies, whether you like them or not, are easier to work with and understand. Regarding spectrum policy, whatever you know from Europe is not likely to be the same in the USA (though physics is still fairly similar).
I was very fortunate to arrive back in the early years of the third millennium to discuss cellular capacity and, as it quickly evolves (“escalates”), too, having a discussion of available cellular frequencies, the associated spectral bandwidth, and whether they really need that 100 million US dollar for radio access expansions.
I was one of the first (from my company) to ask all those “stupid” questions whenever I erroneously did not just assume things surely must be the same as in Europe and ended up with the correct answer that in the USA, things are a “little” different and a lot more complicated in terms of the availability of frequencies and what feeds the demand … the spectrum bandwidth. My arrival was followed by “hordes” of other well-meaning Europeans with the same questions and presumptions, using European logic to solve US challenges. And that doesn’t really work (surprised you not should be). I believe my T-Mobile US colleagues and friends over the years surely must have felt like Groundhog Day all over again at every new European visit.
COMPARING APPLES AND ORANGES.
Looking at US spectrum reporting, it is important to note that it is customary to provide the total amount of spectrum. Thus, for FDD spectrum bands, including both the downlink spectrum portion and uplink spectrum part of the cellular frequency band in question. For example, when a mobile network operator (MNO) reports that it has, e.g., 40 MHz of AWS1 spectrum in San Diego (California), it means that it has 2×20 MHz (or 20+20 MHz). Thus, 20 MHz of downlink (DL) services and 20 MHz of uplink (UL) services. For FDD, both the DL and the UL parts are counted. In Europe, historically, we mainly would talk about half the spectrum for FDD spectrum bands. This is one of the first hurdles to get over in meetings and discussions. If not sorted out early can lead to some pretty big misunderstandings (to say the least). To be honest, and in my opinion, providing the full spectrum holding, irrespective of whether a band is used as FDD or TDD, is less ambiguous than the European tradition.
The second “hurdle” is to understand that a USA-based MNO is likely to have a substantial variation in its spectrum holdings across the US geography. An MNO may have a 40 MHz (i.e., 2×20 MHz) PCS spectrum in Los Angeles (California) and only 30 MHz (2×15 MHz) of the same spectrum in New York or only 20 MHz (2×10 MHz) in Miami (Florida). For example, FCC (i.e., the regulator managing non-federal spectrum) uses 734 so-called Cellular Market Areas or CMAs, and there is no guarantee that a mobile operator’s spectrum position will remain the same over these 734 CMAs. Imagine Dutch (or other European) mobile operators having a varying 700 MHz (used for 5G) spectrum position across the 342 municipalities of The Netherlands (or another European country). It takes a lot of imagination … right? And maybe why, we Europeans, shake our heads at the US spectrum fragmentation, or market variation, as opposed to our nice, neat, and tidy market-wise spectrum uniformity. But is the European model so much better (apart from being neat & tidy)? …
… One may argue that the US model allows for spectrum acquisition to be more closely aligned with demand, e.g., less spectrum is needed in low-population density areas and more is required in high-density population areas (where demand will be much more intense). As evidenced by many US auctions, the economics matched the demand fairly well. While the European model is closely aligned with our good traditions of being solid on average … with our feet in the oven and our head in the freezer … and on average all is pretty much okay in Europe.
Figure 1 and 2 below illustrates a mobile operator difference between its spectrum bandwidth spread across the 734 US-defined CMAs in the AWS1 band and how that would look in Europe.
Figure 2 below is visually an even stronger illustration of mobile operator bandwidth variation across the 734 cellular market areas. The dashed white horizontal line is if the PCS band (a total of 120 MHz or 2×60 MHz) would be shared equally between 4 main nationwide mobile operators ending up at 30 MHz per operator across all CMAs. This would resemble what today is more or less a European situation, i.e., irrespective of regional population numbers, the mobile operator’s spectrum bandwidth at a given carrier frequency would be the same. The European model, of course, also implies that an operator can provide the same quality in peak bandwidth before load may become an issue. The high variation in the US operator’s spectrum bandwidth may result in a relatively big variation in provided quality (i.e., peak speed in Mbps) across the different CMAs.
There is an alternative approach to spectrum acquisition that may also be more spectrally efficient, which the US model is much more suitable for. Aim at a target Hz per Customer (i.e., spectral overhead) and keep this constant within the various market. Of course, there is a maximum realistic amount of bandwidth to acquire, governed by availability (e.g., for PCS, that is, 120 MHz) and competitive bidders’ strength. There will also be a minimum bandwidth level determined by the auction rules (e.g., 5 MHz) and a minimum acceptable quality level (e.g., 10 MHz). However, Figure 2 below reflects more opportunistic spectrum acquisition in CMAs with less than a million population as opposed to a more intelligent design (possibly reflecting the importance of, or lack of, different CMAs to the individual operators).
Thirdly, so-called exclusive use frequency licenses (as opposed to shared frequencies), as issued by FCC, can be regarded accounting-wise as an indefinitely-lived intangible asset. Thus, once a US-based cellular mobile operator has acquired a given exclusive-use license, that license can be considered disposable to the operator in perpetuity. It should be noted that FCC licenses typically would be issued for a fixed (limited) period, but renewals are routine.
This is a (really)big difference from European cellular frequency licenses that typically expire after 10 – 20 years, with the expired frequency bands being re-auctioned. A European mobile operator cannot guarantee its operation beyond the expiration date of the spectrum acquired, posing substantial existential threats to business and shareholder value. In the USA, cellular mobile operators have a substantially lower risk regarding business continuity as their spectrum, in general, can be regarded as theirs indefinitely.
FCC also operates with a shared-spectrum license model, as envisioned by the Citizens Broadband Radio Service (CBRS) in the 3.55 to 3.7 GHz frequency range (i.e., the C-band). A shared-spectrum license model allows for several types of users (e.g., Federal and non-Federal) and use-cases (e.g., satellite communications, radar applications, national cellular services, local community broadband services, etc..) to co-exist within the same spectrum band. Usually, such shared licenses come with firm protection of federal (incumbent) users that allows commercial use to co-exist with federal use, though with the federal use case taking priority over the non-federal. A really good overview of the CBRS concept can be found in “A Survey on Citizens Broadband Radio Service (CBRS)” by P. Agarwal et al.. Wireless Innovation Forum published on 2022 a piece on “Lessons Learned from CBRS” which provides a fairly nuanced, although somewhat negative, view on spectrum sharing as observed in the field and within the premises of the CBRS priority architecture and management system.
Recent data around FCC’s 3.5 GHz (CBRS) Auction 105 would indicate that shared-licensed spectrum is valued at a lower USD-per-MHz-pop (i.e., 0.14 USD-per-MHz-pop) than exclusive-use license auctions in 3.7 GHz (Auction 107; 0.88 USD-per-MHz-pop) and 3.45 GHz (Auction 110; 0.68 USD-per-MHz-pop). The duration of the shared-spectrum license in the case of the Auction 105 spectrum is 10 years after which it is renewed. Verizon and Dish Networks were the two main telecom incumbents that acquired substantial spectrum in Auction 105. AT&T did not acquire and T-Mobile US only picked close to nothing (i.e., 8 licenses).
THE STATE OF CELLULAR PERFORMANCE – IN THE UNITED STATES AND THE REST OF THE WORLD.
Irrespective of how one feels about the many mobile cellular benchmarks around in the industry (e.g., Ookla Speedtest, Umaut benchmarking, OpenSignal, etc…), these benchmarks do give an indication of the state of networks and how those networks utilize the spectral resources that mobile companies have often spend hundreds of millions, if not billions, of US dollars acquiring and not to underestimate in cost and time, spectrum clearing or perfecting a “second-hand” spectrum may incur for those operators.
So how do US-based mobile operators perform in a global context? We can get an impression, although very 1-dimensional, from Figure 1 below.
Ookla’s Speedtest rank (see Figure 3 above) positions the United States cellular mobile networks (as an average) among the Top-20. Depending on the ambition level, that may be pretty okay or a disappointment. However, over the last 24 months, thanks to the fast 5G deployment pace at 600 MHz, 2.5 GHz, and C-band, the US has leapfrogged (on average) its network quality which for many years did not improve much due to little spectrum availability and huge capital investment levels. Something that the American consumer can greatly enjoy irrespective of the relative mobile network ranking of the US compared to the rest of the world. South Korea and Norway are ranked 3 and 4, respectively, regarding cellular downlink (DL) speed in Mbps. The above figure also shows a significant uplift in the speed at the time of introducing 5G in the cellular operators’ networks worldwide.
How to understand the supplied cellular network quality and capacity that the consumer demand and hopefully also enjoy? Let start with the basics:
We might be able to understand some of the dynamics of Figure 3 using Figure 4, which illustrates the fundamental cellular quality (and capacity) relationship with frequency bandwidth, spectral efficiency, and the number of cells (or sectors or sites) deployed in a given country.
Thus, a mobile operator can improve its cellular quality (and capacity) by deploying more spectrum acquired on its existing network, for example, by auctions, leasing, sharing, or other arrangements within the possibilities of whatever applicable regulatory regime. This option will exhaust as the operator’s frequency spectrum pool is deployed across the cellular network. It leaves an operator to wait for an upcoming new frequency auction or, if possible, attempt to purchase additional spectrum in the market (if regulation allows) that may ultimately include a merger with another spectrum-rich entity (e.g., AT&T attempt to take over T-Mobile US). All such spectrum initiatives may take a substantial amount of time to crystalize, while customers may experience a worsening in their quality. In Europe, the licensed spectrum becomes available in cycles of 10 – 20 years. In the USA, exclusive-use licensed spectrum typically would be a once-only opportunity to acquire (unless you acquire another spectrum-holding entity later, e.g., Metro PCS, Sprint, AT&T’s attempt to acquire T-Mobile, …).
Another part of the quality and capacity toolkit is for the mobile operator to choose appropriately spectral efficient technologies that are supported by a commercially available terminal ecosystem. Firstly, migrate frequency and bandwidth away from currently deployed legacy radio-access technology (e.g., 2G, 3G, …) to newer and spectrally more efficient ones (e.g., 4G, 5G, …). This migration, also called spectral re-farming, requires a balancing act between current legacy demand versus the future expectations of demand in the newer technology. In a modern cellular setting, the choice of antenna technology (e.g., massive MiMo, advanced antenna systems, …) and type (e.g., multi-band) is incredibly important for boosting quality and capacity within the operators’ cellular networks. Given that such choices may result in redesigning existing site infrastructure, it provides an opportunity to optimize the existing infrastructure for the best coverage of the consolidated spectrum pool. It is likely that the existing infra was designed with a single or only a few frequencies in mind (e.g., PCS, PCS+AWS, …) as well as legacy antennas, and the cellular performance is likely improved by considering the complete pool of frequencies in the operator’s spectrum holding. The mobile operator’s game should always be to achieve the best possible spectral efficiency considering demand and economics (i.e., deploying 64×64 massive MiMo all over a network may be the most spectrally efficient solution, theoretically, but both demand and economics would rarely support such an apparently “silly” non-engineering strategy). In general, this will be the most frequently used tool in the operators’ quality/capacity toolkit. I expect to see an “arms race” between operators deploying the best and most capable antennas (where it matters), as it will often be the only way to differentiate in quality and capacity (if everything else is almost equal).
Finally, the mobile operator can deploy more site locations (macro and small cells), if permitting allows, or more sectors by sectorization (e.g., 3 → 4, 4 → 5 sectors) or cell split if the infrastructure and landlord allows. If there remains unused spectral bandwidth in the operator’s spectrum pool, the operator may likely choose to add another cell (i.e., frequency band) to the existing site. Particular adding new site locations (macro or small cell) is the most complex path to be taken and, of course, also often the least economic path.
Thus, to get a feeling for the Ookla Speedtest, which is a country average, results of Figure 3, we need, as a starting point, to have the amount of spectral bandwidth for the average cellular mobile operator. This is summarised in below’s Table 1.
It does not take too long to observe that there is only an apparently rather weak correlation between spectrum bandwidth (sub-total and total) and the observed DL speed (even after rescaling to downlink spectrum only). Also, what is important is, of course, how much of the spectrum is deployed. Typically low and medium bands will be deployed extensively, while other high-frequency bands may only have been selectively deployed, and the C-band is only in the process of being deployed (where it is available). What also plays a role is to what degree 5G has been rollout across the network, how much bandwidth has been dedicated to 5G (and 4G), and what type of advanced antenna system or massive MiMo capabilities has been chosen. And then, to provide a great service, a network must have a certain site density (or coverage) compared to the customer’s demand. Thus, it is to be expected that the number of mobile site locations, and the associated number of frequency cells and sectors, will play a role in the average speed performance of a given country.
Figure 5 shows that load (e.g., customers per site) and available capacity (e.g., sites x bandwidth) relative to customers are strongly correlated with the experienced quality (e.g., speed in Mbps). The comparison between the United States and China is interesting as both countries with a fairly similar surface area (i.e., 9.8 vs. 9.6 million sq. km), the USA has a little less than a quarter of the population, and the average mobile US operator would have about one-third of the customers compared to the average Chinese operator (note: China mobile dominates the average). The Chinese operator, ignoring C-band, would have ca. 25 MHz or ~+20% (~50 MHz or ca. +10% if C-band is included) more than the US operator. Regarding sites, China Mobile has been reported to have millions of cell site locations (incl. lots of small cells). The US operator’s site count is in the order of hundreds of thousands (though less than 200k currently, including small cells). Thus, Chinese mobile operators have between 5x to 10x the number of site locations compared to the American ones. While the difference in spectrum bandwidth has some significance (i.e., China +10% to 20% higher), the huge relative difference in site numbers is one of the determining factors in why China (i.e., 117 Mbps) gets away with a better speed test score that is better than the American one (i.e., 85 Mbps). While theoretically (and simplistically), one would expect that the average Chinese mobile operator should be able to provide more than twice the speed as compared to the American mobile operator instead of “only” about 40% more, it stands to show that the radio environment is a “bit” more complex than the simplistic view.
Of course, the US-based operator could attempt to deploy even more sites where it matters. However, I very much doubt that this would be a feasible strategy given permitting and citizen resistance to increasing site density in areas where it actually would be needed to boost the performance and customer experience.
Thus, the operator in the United States must acquire more spectrum bandwidth and deploy that where it matters to their customers. They also need to continue to innovate on leapfrogging the spectral efficiency of the radio access technologies and deploy increasingly more sophisticated antenna systems across their coverage footprint.
In terms of sectorization (at existing locations), cell split (adding existing spectrum to an existing site), and/or adding more sophisticated antenna systems is a matter of Capex prioritization and possibly getting permission from the landlord. Acquiring new spectrum … well, that depends on such new spectrum somehow becomes available.
Where to “look” for more spectrum?
WHERE COULD MORE SPECTRUM COME FROM?
Within the so-called “beachfront spectrum” covering the frequency range from 225 MHz to 4.2 GHz (according to NTIA), only about 30% (ca. 1GHz of bandwidth within the frequency range from 600 MHz to 4.2 GHz) is exclusively non-Federal, and mainly with the mobile operators as exclusive use licenses deployed for cellular mobile services across the United States. Federal authorities exclusively use a bit less than 20% (~800 MHz) for communications, radars, and R&D purposes. This leaves ca. 50% (~2 GHz) of the beachfront spectrum shared between Federal authorities and commercial entities (i.e., non-Federal).
For cellular mobile operators, exclusive use licenses would be preferable (note: at least at the current state of the relevant technology landscape) as it provides the greatest degree of operational control and possibility to optimize spectral efficiency, avoiding unacceptable levels of interference either from systems or towards systems that may be sharing a given frequency range.
The options for re-purposing the Federal-only spectrum (~800 MHz) could, for example, be either (a) moving radar systems’ operational frequency range out of the beachfront spectrum range to the degree innovation and technology supports such a migration, (b) modernizing radar systems with a focus of making these substantially more spectrally efficient and interference-resistant, (c) migratedfederal-only communications services to commercially available systems (e.g., 5G federal-only slicing) similar to the trend of migrating federal legacy data centers to the public cloud. Within the shared frequency portion with the ~2 GHz of bandwidth, it may be more challenging as considerable commercial interests (other than mobile operators) have positioned that business at and around such frequencies, e.g., within the CBRS frequency range. This said, there might also be opportunities within the Federal use cases to shift applications towards commercially available communication systems or to shift them out of the beachfront range. Of course, in my opinion, it always makes sense to impose (and possibly finance) stricter spectral efficiency conditions, triggering innovation on federal systems and commercial systems alike within the shared portion of the beachfront spectrum range. With such spectrum strategies, it appears compelling that there are high likelihood opportunities for creating more spectrum for exclusive license use that would safeguard future consumer and commercial demand and continuous improvement of customer experience that comes with the future demand and user expectations of the technology that serves them.
I believe that the beachfront should be extended beyond 4.2 GHz. For example aligning with band-79, whose frequency range extends from 4.4 GHz to 5 GHz, allows for a bandwidth of 600 MHz (e.g., China Mobile has 100 MHz in the range from 4.8 GHz to 4.9 GHz). Exploring additional re-purposing opportunities for exclusive use licenses in what may be called the extended beachfront frequency range from 4.2 GHz up to 7.2 GHz should be conducted with priority. Such a study should also consider the possibility of moving the spectrum under exclusive and shared federal use to other frequency bands and optimizing the current federal frequency and spectrum allocation.
The NTIA, that is, the National Telecommunications and Information Administration, is currently (i.e., 2023) for the United States developing a National Spectrum Strategy (NSS) and the associated implementation plan. Comments and suggestions to the NSS were possible until the 18th of April, 2023. The National Spectrum Strategy should address how to create a long-term spectrum pipeline. It is clear that developing a coherent national spectrum strategy is critical to innovation, economic competition, national security, and maybe re-capture global technology leadership.
So who is the NTIA? What do they do that FCC doesn’t already do? (you may possibly ask).
WHO MANAGES WHAT SPECTRUM?
Two main agencies in the US manage the frequency spectrum, the FCC and the NTIA.The Federal Communications Commission, the FCC for short, is an independent agency that exclusively regulates all non-Federal spectrum use across the United States. FCC allocates spectrum licenses for commercial use, typically through spectrum auctions. A new or re-purposed commercialized spectrum has been reclaimed from other uses, both from federal uses and existing commercial uses. Spectrum can be re-purposed either because newer, more spectrally efficient technologies become available (e.g., the transition from analog to digital broadcasting) or it becomes viable to shift operation to other spectrum bands with less commercial value (and, of course, without jeopardizing existing operational excellence). It is also possible that spectrum, previously having been for exclusive federal use (e.g., military applications, fixed satellite uses, etc..), can be shared, such as the case with Citizens Broadband Radio Service (CBRS), which allows non-federal parties access to 150 MHz in the 3.5 GHz band (i.e., band 48). However, it has recently been concluded that (centralized) dynamic spectrum sharing only works in certain use cases and is associated with considerable implementation complexities. Multiple parties with possible vastly different requirements co-existence within a given band is very much work-in-progress and may not be consistent with the commercialized spectrum operation required for high-quality broadband cellular operation.
In parallel with the FCC, we have the National Telecommunications and Information Administration, NTIA for short. NTIA is solely responsible for authorizing Federal spectrum use. It also acts as the President of the United State’s principal adviser on telecommunications policies, coordinating the views of the Executive Branch. NTIA manages about 2,398 MHz (69%) within the so-called “beachfront spectrum” range of 225 MHz to 3.7 GHz (note: I would let that Beachfront go to 7 GHz, to be honest). Of the total of 3,475 MHz, 591 MHz (17%) is exclusively for Federal use, and 1,807 MHz (52%) is shared (or coordinated) between Federal and non-Federal. Thus, leaving 1,077 MHz (31%) for exclusive commercial use under the management of the FCC.
NTIA, in collaboration with the FCC, has been instrumental in the past in freeing up substantial C-band spectrum, 480 MHz in total, of which 100 MHz is conditioned on prioritized sharing (i.e., Auction 105), for commercial and shared use that subsequently has been auctioned off over the last 3 years raising USD 109 billion. In US Dollar (USD) per MHz per population count (pop) we have on average ca. USD 0.68 per MHz-pop from the C-band auctions in the US, compared to USD 0.13 per MHz-pop in Europe C-band auctions, and USD 0.23 per MHz-pop in APAC auctions. It should be remember that the United States exclusive-use spectrum licenses can be regarded as an indefinite-lived intangible asset while European spectrum rights expire between 10 and 20 years. This may explain a big part of the pricing difference between US-based spectrum pricing and that of Europe and Asia.
NTIA and FCC jointly manage all the radio spectrum, licensed (e.g., cellular mobile frequencies, TV signals, …) and unlicensed (e.g., WiFi, MW Owens, …) of the United States, NTIA for Federal use, and FCC for non-Federal use (put simply). FCC is responsible for auctioning spectrum licenses and is also authorized to redistribute licenses.
RESPONSE TO NTIA’s National Spectrum Strategy Request for Comments
Here are some of key points to consider for developing a National Spectrum Strategy (NSS).
The NTIA National Spectrum Strategy (NSS) should focus on creating a long-term spectrum pipeline. Developing a coherent national spectrum strategy is critical to innovation, economic competition, national security, and global technology leadership.
NTIA should aim at significant amounts of spectrum to study and clear to build a pipeline. Repurposing at least 1,500 Mega Hertz of spectrum perfected for commercial operations is good initial target allowing it to continue to meet consumer, business, and societal demand. It requires more than 1,500 Mega Hertz to be identified for study.
NTIA should be aware that the mobile network quality strongly correlates with the mobile operators’ spectrum available for their broadband mobile service in a global setting.
NTIA must remember that not all spectrum is equal. As it thinks about a pipeline, it must ensure its plans are consistent with the spectrum needs of various use cases of the wireless sectors. The NSS is a unique opportunity for NTIA to establish a more reliable process and consistent policy for making the federal spectrum available for commercial use. NTIA should reassert its role, and that of the FCC, as the primary federal and commercial regulator of spectrum policy.
A balanced spectrum policy is the right approach. Given the current spectrum dynamics, the NSS should prioritize identifying exclusive-use licensed spectrum instead of, for example, attempting co-existence between commercial and federal use.
Spectrum-band sharing between commercial communications networks and federal communications, or radar systems, may impact the performance of all the involved systems. Such practice compromises the level of innovation in modern commercialized communications networks (e.g., 5G or 6G) to co-exist with the older legacy systems. It also discourages the modernization of legacy federal equipment.
Only high-power licensed spectrum can provide the performance necessary to support nationwide wireless with the scale, reliability, security, resiliency, and capabilities consumers, businesses, and public sector customers expect.
Exclusive use of licensed spectrum provides unique benefits compared to unlicensed and shared spectrum. Unlicensed spectrum, while important, is only suitable for some types of applications, and licensed spectrum under shared access frameworks by CBRS is unsuited for serving as the foundation for nationwide mobile wireless networks.
Allocating new spectrum bands for the exclusive use of licensed spectrum positively impacts the entire wireless ecosystem, including downstream investments by equipment companies and others who support developing and deploying wireless networks. Insufficient licensed spectrum means increasingly deteriorating customer experience and lost economic growth, jobs, and innovation.
Other countries are ahead of the USA in developing plans for licensed spectrum allocations, targeting the full potential of the spectrum range from 300 MHz up to 7 GHz (i.e., the beachfront spectrum range), and those countries will lead the international conversation on licensed spectrum allocation. The NSS offers an opportunity to reassert U.S. leadership in these debates.
NTIA should also consider the substantial benefits and economic value of leading the innovation in modernizing the legacy spectrally in-efficient non-commercial communications and radar systems occupying vast spectrum resources.
Exclusive-use licensed spectrum has inherent characteristics that benefit all users in the wireless ecosystem.
Consumer demand for mobile data is at an all-time high and only continues to surge as demand grows for lightning-fast and responsive wireless products and services enabled by licensed spectrum.
With an appropriately designed and well-sized spectrum pipeline, demand will remain sustainable as supplied spectrum capacity compared to the demand will remain or exceed today’s levels.
Networks built on licensed spectrum are the backbone of next-generation innovative applications like precision agriculture, telehealth, advanced manufacturing, smart cities, and our climate response.
Licensed spectrum is enhancing broadband competition and bridging the digital divide by enabling 5G services like 5G Fixed Wireless Access (FWA) in areas traditionally dominated by cable and in rural areas where fiber is not cost-effective to deploy.
NTIA should identify the midband spectrum (e.g., ~2.5GHz to ~7GHz) and, in particular, frequencies above the C-band for licensed spectrum. That would be the sweet spot for leapfrogging broadband speed and capacity necessary to power 5G and future generations of broadband communications networks.
The National Spectrum Strategy is an opportunity to improve the U.S. Government’s spectrum management process.
The NSS allows NTIA to develop a more consistent and better process for allocating spectrum and providing dispute resolution.
The U.S. should handle mobile networks without a new top-down government-driven industrial policy to manage mobile networks. A central planning model would harm the nation, severely limiting innovation and private sector dynamism.
Instead, we need a better collaboration between government agencies with NTIA and the FCC as the U.S. Government agencies with clear authority over the nation’s spectrum. The NSS also should explore mechanisms to get federal agencies (and their associated industry sectors) to surface their concerns about spectrum allocation decisions early in the process and accept NTIA’s role as a mediator in any dispute.
I greatly acknowledge my wife, Eva Varadi, for her support, patience, and understanding during the creative process of writing this article. Of course, throughout the years of being involved in T-Mobile US spectrum strategy, I have enjoyed many discussions and debates with US-based spectrum professionals, bankers, T-Mobile US colleagues, and very smart regulatory policy experts in Deutsche Telekom AG. I have the utmost respect for their work and the challenges they have faced and face. For this particular work, I cannot thank Roslyn Layton, PhD enough for nudging me into writing the comments to NTIA. By that nudge, this little article is a companion to my submission about the US Spectrum as it stands today and what I would like to see with the upcoming National Spectrum Strategy. I very much recommend reading Roslyn’s far more comprehensive and worked-through comments to the NTIA NSS request for advice. A final thank you to John Strand (who keeps away from Linkedin;-) of Strand Consult for challenging my way of thinking and for always stimulating new ways of approaching problems in our telecom sector. I very much appreciate our discussions.
Ronald Harry Coase, “The Federal Communications Commission”, The Journal of Law & Economics, Vol. 2 (October 1959), pp. 1- 40. In my opinion, a must-read for anyone who wants to understand the US spectrum regulation and how it came about.
I make extensive use of the Spectrum Monitoring site, which I can recommend as one of the most comprehensive sources of frequency allocation data worldwide that I have come across (and is affordable to use).
Back in 2014, working at Deutsche Telekom AG and responsible for Technology Economics, we looked at alternatives to fiber deployment in Germany (and other markets). It was clear that deploying fiber in Germany would be massively costly and take a very long time… As an incumbent solely relying on xDSL, there was unease in general and in particular with observing that HFC (hybrid-fiber-coaxial) providers were gaining a lot of traction in key markets around Germany. There was an understanding that fiber would be necessary to secure the longer-term survivability of the business. Even as far back as 2011, this was clear to some visionaries within Deutsche Telekom. My interest at the time was whether fixed wireless access (FWA) solutions could be deployed faster (yes, it could and can, at least in Germany) and bridge the time until fiber was sufficiently deployed and with an economically attractive uptake that allowed an operator to retire the FWA solution or re-purpose it for normal mobile access. It economically did not make sense to deploy FWA everywhere … by far not. Though we found that in certain suburban and rural areas, it could make sense to deploy FWA solutions. … So why did it not happen? At the time, the responsible executives for fixed broadband deployment (no, no converged organization at the time) were nervous that “their” fiber Capex would be re-prioritized to FWA and thus taken away from their fiber deployment. Resulting in even further delays in fiber coverage in Germany. Also … they argued the write-off of fiber investments (e.g., 15 – 20+ years) is so much much longer compared to FWA (e.g., 5 – 7 years), and when factoring in the useful lifetime of fiber versus FWA, it made no sense to deploy it (of course ignoring that we could deploy FWA within 6 months while the fiber in that area might not be present in the next 10+ years;-).
I learned three main lessons (a lot more, actually … but that’s for my memoirs if I remember;-)
FWA can be made economically favorable but not universally so everywhere.
FWA can be a great instrument to bridge the time until fiber deployment has arrived and a given demand (uptake) in an area exists (you just need to make sure your FWA design accounts for the temporary nature of the purpose of your solutions).
FWA at high frequencies (e.g., >20 GHz) is not “just” an overlay of an MNOs existing mobile network. The design should be considered a standalone network, with maximum re-use of any existing infrastructure, with line-of-sight (LoS) to customers and LoS redundancy build-in (i.e., multiple redundant paths to a customer).
We are now 10+ years further (and Germany is still Europe’s laggard in terms of fiber deployment and will remain so for many years to come), and the technology landscape that supports both fiber and fixed wireless access is much further as well…
In the following, it is always good to keep in mind that
“Even if your something appears less economically attractive than something else, if that something else is not available or present, your solution may be an interesting opportunity to capture growth to your business. At least within a given window of opportunity.”
and, so it begins …
FIXED WIRELESS ACCESS (FWA).
In this blog, I will define Fixed Wireless Access (FWA) as a service that provides a fixed-like wireless-based internet broadband connection to a household. FWA bypasses the need for a last-mile fixed wired connection from a nearby access point (e.g., street cabinet) to a customer’s household. Thus substituting the need for a fixed copper, coax, or fiber last-mile connection. I will, in general, position FWA in a modern context of 5G, which may enable existing MNOs to bridge the time until they will have fiber coverage, for example, rural and sub-urban areas. Or, as the thinking goes (for some), completely avoid the need for costly and (allegedly) less profitable deployment of fiber in less household-dense areas where more kilometer of fiber needs to be deployed in order to reach the same amount of households compared to an urban or dense urban area. Of course, companies may also be tempted to build FWA-dedicated ISP networks operating in the mmWave range (i.e., >20 GHz) or in the so-called mid-bands range (e.g., ≥ 2.5 GH, C-band, …) to provide higher quality internet services to sub-urban and rural customers where the economics for fiber coverage and connectivity may be comparably challenged in terms of economics and time to fiber availability.
Figure 1 below provides an overview and comparison of the various ways we connect our customers’ homes, with the exception of LEO satellite and stratospheric drone-based connectivity solutions (it’s another very interesting story). So, illustrating terrestrial network-based connectivity to the household with either a fixed-line (buried or aerial) or wireless.
For the wireless connection between the service provider’s access network and the household, we have several options;
(1) The Fixed Wireless Access (FWA) network provides a dedicated wireless link between the service provider’s network and the customer’s home. In order to maximize the customer experience, typically, an outdoor customer premise antenna (CPA) would have to be installed on the exterior of a household, offering line-of-sight with the provider’s own advanced antenna residing on its access network infrastructure. The provider will likely dedicate a sufficient amount of wireless spectrum bandwidth (in MHz) to provide a competitive (to fixed) broadband service. In a 5G SA (standalone) setting, this could be a cellular spectrum in the mid-band range (≥ 2.5 – 10 GHz) or (or and) mmWave spectrum above 20 GHz. An access network providing fixed-wireless services in the mid-band spectrum typically would overlay an existing mobile network (if the provider is also an MNO) with possibly site additions allowing for higher-availability services to households as well as increase the scale and potential of connecting households due to increased LoS likelihood. In case the services rely on mmWave frequency bands, I would in general, expect a dedicated network infrastructure would have to be built to provide sufficient household scale, reliability, and availability to households in the covered broadband service area. This may (also) rely on existing mobile network infrastructure if the provider is an established MNO, or it may be completely standalone. My rule of thumb is that for every household that is subscribing to the FWA service, I need at least 2, preferably 3, individual line-of-sight solutions to the household CPA. Most conventional cellular network designs (99+% of all there are out in the wild) cannot offer that kind of coverage solution.
The customer premise antenna (CPA) connects to the household’s customer premise equipment (CPE). The CPE provides WiFi coverage within the household either as a single unit or as part of a meshed WiFi household network.
(2) A service that is based on Fixed Mobile Substitution (FMS) utilizes existing cellular resources, such as infrastructure and spectrum bandwidth, to provide a service to a cellular-based (e.g., 4G/5G) customer premise equipment (CPE) residing inside a customer’s household. The CPE connects to the mobile network (via 4G and/or 5G ) and enjoys the quality of the provider’s mobile network. Inside the household, the CPE offers WiFi coverage that is utilized by the household’s occupants. As existing mobile resources are shared with regular mobile customers that may also be in the same household as the FMS solution itself, the service provider needs to carefully balance capacity and quality between the two customer segments, with the household one typically being the greedy one (with respect to network resources and service plans) and impacting network resources substantially more than the regular mobile user (e.g., usually 20+ to 1).
FWA has been around the telco and ISP toolbox for many years in one form or another. The older (or let’s put it nicer, the experienced) reader will remember that a decade ago, many of us believed that WiMax (Worldwide Interoperability for Microwave Access) was the big thing to solve all the ailing (& failings) of 3G, maybe even becoming our industry’s de facto 4G standard. WiMax promised up to 1 Gbps for a fixed (wireless) access base station and up to around 100 Mbps at low mobility (i.e., <50 km per hour). As we know today, it should not be.
FAST FORWARD TO TODAY & TOMORROW WITH 5G AND FIBER SERVICES.
GSMA (GSM Association, the mobile interest group) has been fairly bullish on the advantages and opportunities of 5G-based Fixed Wireless Access (5G-FWA). Alleging a significant momentum behind FWA with (1) 74+ broadband service providers launching FWA services globally, (2) Expecting 40 million 5G FWA subscribers by 2025. Note globally, as of October 2022, there were 5.5 billion unique mobile subscribers. So 5G FWA amounts to <1% of unique subscribers, and last but not least (3) They expect up to 80% cost saving versus fiber to the home (FTTH) @ 100 Mbps downlink. GSMA lists more advantages according with GSMA but the 3 here are maybe the most important.
According to GSMA, in Western Europe, they expect roughly around 275+ million people will subscribe to 5G by 2025. This number represents ca. 140 million unique 5G households. Applying household scaling between western Europe and Global on the global total of 40 million 5G FWA HH, one should expect to capture between 4 to 5 million 5G FWA households or ca. 2.5% FWA HH penetration in Western Europe by 2025 (see below for details of this estimate). This FWA number also corresponds to a ca. 4% of all unique 5G households, or ca. 2% of all unique 5G subscribers, or ca. 1% of all unique mobile subscribers (in 2025). While 40 million (5 million) globally (in Western Europe) sounds like a large number, it is, to all effects rather minuscule and underwhelming compared to the total mobile and fixed broadband market.
The GSMA report, “The 5G FWA opportunity: series highlights” (from July 2022) also provides a 2025 projection for 5G FWA connections as a percentage of households across various countries. In Figure 3 below, find the GSMA projections with, as a comparison, the estimated fiber-to-the-home connections (FTTH) in 2025 and, for reference, the actual FTTH connections in 2021. It seems compelling to assume that 5G FWA would be an alternative to fiber at home or an HFC D3.1 (D = Docsis) connection. Of course, it is only possible to get a service if the technology of choice covers the household. A fiber connection to your household requires that there is a fiber passing in the proximity of your household. Thus the degree of fiber coverage is important in order to assess the fiber subscription uptake possible. Likewise, a 5G FWA connection requires that the household is within a very good and high-quality 5G coverage of the FWA provider (or the underlying network operator). Figure 4 below provides an overview of 2021 actual and 2026 (projected) fiber-based household coverage (i.e., homes passed) percentages in Western Europe.
If we take a look at 5G coverage, which may be an enabler for FWA services that can compete with fiber quality, it would be fairly okay to assume that most mobile operators in Western Europe would have close to a full 5G population (and households) coverage. However, accessing the 5G quality of that coverage would be problematic. 5G coverage may be based on 700 MHz piggybacking on LTE (i.e., non-standalone, NSA 5G), providing nearly 100% household coverage, it may involve considerable mid-band (i.e., > 2.1 GHz frequency bands) 5G coverage in urban and suburban areas with varying degree of rural coverage, it may also involve the deployment of mmWave (i.e., >20 GHz frequency bands) as an overlay to the normal macro cellular network or as dedicated standalone fixed-wireless access network or a combination of both.
Actually, one might also think that in geographical areas where fiber coverage, or D3.1-based HFC, is relatively limited or completely lacking, 5G FWA opportunities would be more compelling due to the lack of competing broadband alternatives. If the premise is that the 5G FWA service should be fiber-like, it would require good quality 5G coverage with speeds exceeding 100 Mbps at high availability and consistency. However, if the fixed broadband service that FWA would compete with is legacy xDSL, then some of the requirements for fiber-like quality may be relaxed (e.g., 100+ Mbps, very high availability, …).
What are the opportunities, and where? Focusing on fiber deployment in Western Europe, Figure 5 illustrates homes covered by fiber and those with no fiber coverage in urban and rural areas as of 2021 (actual). The figure below also provides a forecast of home coverage and homes missing by 2026.
As Figure 5 above shows, the urban fiber deployment in Europe is happening at a fast pace in most markets, and the opportunities for alternatives (at scale) may at the same time be seen as diminishing apart from a few laggard markets (e.g., Austria, Belgium, Germany, UK, ..). Rural opportunities for broadband alternatives (to fiber) may be viewed more optimistically with many more households only having access to aging copper lines or relative poor HFC.
A 5G FWA provider may need to think about the window of opportunity to return on the required investment. To address this question, Figure 6 below provides a projection for when at least 80% of households will be connected in urban and rural areas. Showing that in some markets, rural areas may remain more attractive for longer than the corresponding urban areas. Further, if one views the 5G FWA as a bridge to fiber availability, there may be many more opportunities for FWA than what Figures 5 and 6 allude to.
Looking at the opportunity for fiber alternatives going forward, Figure 7 below provides the quantum of households that remain to be covered by fiber. This lack of fiber also creates opportunities for broadband alternatives, such as 5G FWA, and maybe non-terrestrial broadband solutions (e.g., Starlink, oneWeb,…). Cellular operators, with a good depth of site coverage, should be able to provide competitive alternatives to existing legacy fixed copper services, as long as LoS is not required, at least. Particularly in some rural areas, depending on the site density and spectrum commitment, around rural villages and towns. Cellular networks may not have much capacity and quality to spare in urban areas for fixed mobile substitution (FMS), at least if designed economically. This said, and depending on the cellular, and fixed broadband competitive environment, FMS-based services (4G and 5G) may be able to bridge the short time until fiber becomes available in an area. This can be used by an incumbent telco that is in the process of migrating its aging copper infrastructure to fiber or as a measure by competing cellular operators to tease copper customers away from that incumbent. Hopefully, those cellular Telcos have also thought about FMS migration off their cellular networks to a permanent fixed broadband solution, such as fiber (or a dedicated mmWave-based FWA service).
As pointed out previously, GSMA projects by 2025 ca. 5 million 5G FWA households in Western Europe. This is less than 3 out of every 100 regular households. Compared with fiber coverage of households estimated to be around 60 out of 100 by 2025. Given that some countries in Western Europe are lagging behind fiber deployment (e.g., Germany, UK, Italy, … see charts above), leaving a large part of their population without modern fixed broadband, one could expect the number might have been bigger than just a few percent. However, 5G FWA at 3.x GHz, and at mmWave frequencies require line-of-sight connections to a customer’s household to provide fiber-like quality and stability. Cellular networks were (obviously) never designed to have LoS to its customers as the cellular frequencies (≤ 3 GHz) were sufficiently low not to be “bothered” (too much) by penetration losses. At and above 3 GHz LoS is increasingly required if a fiber-like service is required.
Another aspect that is often under-appreciated or flat-out ignored (particularly by cellular-minded marketing & sales professionals), is the need for an exterior household customer premise antenna (CPA) that will allow a household to pick up the FWA signal at a higher quality (compared to a gateway antenna indoor due to penetration loss) and with minimum network interference, which may reduce overall quality and capacity in the cellular network (that coincidentally will hurt the normal cellular user as well as other FWA customers). The reason for this neglect is, in my opinion, that it is (allegedly) more difficult to sell such as product to cellular-minded customers and to cellular-minded salespeople as well. It also may increase the cost of technical support due to more complex installation procedures (compared to having a normal mobile phone or indoor gateway) than just turning on a cellular-WiFi modem box inside the home, and it may also result in higher ongoing customer service cost due to more components compared to either a cellular phone or a cellular modem.
GSMA Intelligence group compared the total cost of ownership (TCO) of a dedicated 5G FWA mmWave-based connection with that of fiber-to-the-home (FTTH) for an MNO with an existing 5G network in Europe. It appears that the GSMA’s TCO model(s) are rich in detail regarding the underlying traffic models and cost drivers. Moreover, it would also appear that their TCO analysis is (at least at some level) based on an assumed kilometer-based TCO benchmark. It is unclear to me whether Opex has been considered. Though given the analysis is TCO, I assume that it is the case it was considered.
GSMA (for Europe) found that compared to fiber-based household connectivity, 5G FWA is 80% cheaper in rural areas, 60% cheaper in suburban, and 35% cheaper in urban areas compared to an FTTH deployment.
My initial thoughts, without doing any math on the GSMA results, was that I could (easily) imagine that 5G FWA would require less absolute Capex compared to deploying fiber to the home. At least for buried fiber deployment. I would be less confident wrt this result when it comes to aerial fiber deployment, but maybe it is also still a valid result. However, when considering Opex, what 5G FWA incrementally contributes, I would be much less sure that 5G FWA would be outperforming FTTH. At the least in rural and suburban areas where the household customer density per 5G FWA site would be very low (even before considering the opportunity based on LoS likelihood). Thus, the 5G FWA Opex scaled with the number of household subscribers may be a lot less favorable than FTTH, considering the access energy consumption and technical support costs alone. This is even before considering whether a normal rural and a suburban cellular network is at all suitable (designed for) for providing high availability and high-quality+ fixed-like broadband services delivered by 3.x GHz or mmWave frequencies (which in rural and suburban areas may be even more problematic on existing cellular networks).
I would generally not expect that the existing rural/suburban cellular network would be remotely adequate to permanently replace the need for fiber-connected homes. We would most likely need to densify (add new sites) to ensure high quality and high availability connectivity to customers’ premises. This typically would translate into line-of-site (LoS) requirements between the 5G FWA antenna and the customers’ households. Also, to ensure high availability, similar to a fiber connection, we should expect the need for redundant LoS connectivity to the customers’ households (note: experience has shown that having only one LoS connection compromises availability and consistency/reliability substantially). Such redundant connectivity solutions would be even more difficult to find in existing cellular networks. These considerations would, if considered, both add substantial Capex and additional Opex to the 5G FWA TCO reducing the economical (and maybe commercial) attractiveness compared to FTTH.
HOW TO MAKE APPLES AND ORANGES MORE LIKE BANANAS.
As mentioned above, GSMA appears to base (some of) its economic conclusions on a per kilometer (km) unit driver. That is Euro-per-km. While I don’t have anything particular against this driver, apart from being rather 1-dimensional, I believe it provides fewer insights than maybe others’ more direct drivers of income, capital, and operational cost as well as, in the end, a given solution’s commercial success.
I prefer to use the number of households (HH) per square kilometer, thus HH per km2. For fiber deployment and household coverage, I would use fiber per HH passed (HHP). Fiber connecting the household, providing the actual connection (“the last mile”) to customers’ home, I use fiber HH connected (HHC). The intention behind fiber coverage, what is called household passed, is to be able to connect households by extending the fiber to the “last mile” (or the last-1.61-kilometer) and start generating revenues that return on the capital investment done in the first place. Fiber coverage can be thought of as a real option to connect a home. Fiber coverage is obviously a necesity for connecting a home. Similarly, building dedicated fixed-wireless access infrastructure, incrementally on existing cellular infra or from scratch, is to provide a fixed-like high-quality wireless connection to a household.
Thus household density is a very important driver for the commercial potential, as well as how much of the deployment capital and operational cost can be assigned to a given household in a given geographical area. Urban areas, in general, have more households than suburban and rural areas. The deployment of Capex and Opex in urban areas will be lower per household than in suburban and more rural urbanized areas.
Every household that is fiber covered, implying that the dwelling is within a short reach of the main fiber passing through and ultimately connected, requires an investment with an operational cost associated and revenue for the service is supported by the connection. Fiber total cost of ownership (TCO) will depend on the amount of households covered and the number of households directly connected to a paying customer. For the fiber deployment economics, I am using data from my “Nature of Telecom Capex” (see Figure 16, and please note that the data is for buried fiber) that provides the capital cost of fiber coverage (households passed) and for homes fiber connected, both as a function of household density. For fiber homes passed (HHP) economics, I am renormalizing to fiber homes connected (HHC). Thus if 90% of homes are covered (i.e., passed) in an area and 60% of the homes passed are connected, those connected homes pay for the remaining unconnected homes (30%) under the fiber coverage. This somewhat inflates the cost of connecting a home but is similar to the economic logic of cellular coverage, where the cost is paid by customers having access to the cellular site, even if the cellular site usually covers a lot more people than customers.
In general, fiber deployment becomes increasingly costly as the deployment moves from denser urbanized areas out to suburban and finally rural areas as the household density decreases and more area (and kilometers) need to be covered to capture the same amount of households as in urban areas. Also, it is worth keeping in mind that in countries with the possibility of substantial aerial fiber deployment (e.g., Spain, France, Portugal, Poland, etc..), this leads to a significant unit cost reduction in comparison to buried fiber deployment as we know it from Germany, Netherlands and Denmark. Figure 4 above provides an overview of Western European countries with aerial fiber deployment possibilities and those where buried fiber is required.
For an incremental FWA solution, an existing cellular site will be used. The site location will offer a coverage area where normal broadband cellular services can be provided. Households can of course be connected either via a normal mobile device or a dedicate inhourse gateway connecting to the cellular network (possibly via an exterior CPA) and offering indoor WiFi coverage. For scalable fiber-like wireless quality (e.g., stability and speed) of effective speeds exceeding 100+ Mbps per household connection to be offered from a normal cellular site we typically need line-of-site (LoS) to a customer home as well as a substantial amount of dedicated spectrum bandwidth (100+ MHz) provisioned on an advanced antenna system (AAS e.g., massive MiMo 64×64). The 5G FWA solution, I am assuming, is one that requires the receiving customer to have an outdoor antenna installed on the customer’s home with LoS to the cellular site hosting the FWA solution. The solution is assumed to cover 1 km2 (range of ca. 560 meters) with an effective speed of 300 Mbps per connection. That throughput should hold up to a given connection load limit, after which the speed is expected to decrease as additional household connections are added to the cellular site.
One of, in my opinion, the biggest assumptions (or neglects) of the fiber-like 5G FWA service to households at scale (honestly, a couple of % of HH is not worth discussing;-) is the ability to achieve a line-of-sight between the provider’s cellular site antenna and that of a household with its own customer premise antenna (CPA). For 3.x GHz services, one may assume that everything will still work nicely without LoS and with an inhouse gateway without supporting exterior CPA. I agree … with that premise … if what is required is to beat a xDSL or poor HFC service. There are certainly still many places in Western Europe where that may even make good business sense to attempt to do (that is, competing inferior fixed legacy “broadband” services). The way that cellular networks have been designed (which obviously also have to do with the relative low cellular frequency ranges of the past) is not supporting LoS at scale in urbanized environments. Some great work by professor Dr Akram Al-Hourani, summarised in Figure 9 below, clearly illustrates the difficulty in achieving LoS in urban areas. While I am of the opinion that the basic logic of urban LoS is straightforward, it seems that cellular folks tend to be so used to having (good) cellular coverage pretty much anywhere that it is forgotten when considering higher frequencies that work much better at (or only with) line-of-sight.
The lack of LoS in areas targeted for 5G FWA services needs to be considered in the economic analysis. At least if you are up against fiber-like quality and your intention is to compete at scale (some household opportunity as is the case for fiber). For your FWA cellular-based network, this would often require some degree of densification compared to the as-is cellular network that may be in place. In my work below, I have assumed that my default 5G FWA configuration and targeted service requires 6 sectors covering a 1 km2 of a given urbanized household density. The consequence of that may be that a new (greenfield) site will be required in order to provide 5G FWA at scale (>10+% of HH).
The economics of this solution is straightforward. I have an upfront investment in enabling the FWA solution with a targeted quality level (e.g., ). In a first approximation and up to a predefined (and pre-agreed as sellable with Marketing), this investment is independent of the number of household customers I get. Of course, at some given load & quality conditions, the FWA capacity may have to be expanded by, for example, adding more capable antennas, more FWA (relevant) spectrum, additional sectors, or building a new site. It should be noted that I have not considered the capacity expansion part in the presented analysis in this article. Thus, as the amount of connected FWA households increases, the quality, in general, and speed, in particular, would decrease (typically by a non-linear process).
Most cellular networks have a substantial part of their infrastructure that does not generate any substantial amount of traffic. In other words, its resources are substantially under-utilized in most cellular networks. Part of building a cellular network is to ensure coverage is guaranteed to almost all of the population (98%+) and geography (>90%), irrespective of the expected demand. Some Telcos’ obsession with public speed & performance tests & benchmarks (e.g., Umlaut, Ookla, etc…) has resulted in many networks having an “insane” (un-demanded and highly un-economical) amount of capacity and quality in coverage areas without any particular customer demand. This typically leads to industry consultants proposing to use all that excess quality for what they may call FWA. I would call it FMS (but what’s in a name). Though, even if there may be a lot of excess cellular capacity and quality in rural and subs-urban areas, it’s hardly fiber-like. And it is also highly unlikely to offer the same scale opportunity in terms of households as a fiber deployment would do (hint: LoS likelihood). The opportunity that is exploitable is to compete with xDSL and poor-quality HFC (if available at all). If an area doesn’t have fiber and no good quality coax, that excess cellular capacity can be used as an alternative to xDSL.
To provide competitive fiber-like FWA services with wireless on top of an existing cellular network, we need to design it “right”. Our aim should be a speed well above 100 Mbps (e.g., 300 Mbps) with stability and availability that requires a different design principle than current legacy cellular networks. To provide a 300 Mbps wireless household connection we could start out with a bandwidth of 100 MHz at 3.5 GHz (i.e., 5G mid-band as an example). Later it is possible to upgrade to or add a mmWave solution with even more bandwidth (e.g., 20 to 300 GHz frequency range with bandwidths of multiples of GHz). In order to get both stability and availability, I will assume that I need a minimum of two but preferably three different LoS solutions for an individual household. If no fiber or other high-quality fixed broadband competitors are around, this requirement may be relaxed (although I think a minimum of two LoS connections are required to provide a real fixed broadband alternative at frequencies above 3 GHz).
SOME COMPARATIVE RESULTS.
In my economic analysis of fiber deployment and 5G-based fixed wireless access, the total cost of ownership (TCO) is presented relative to the number of households connected. This way of presenting the economics has the advantage of relating costs directly to the customer that will pay for the service.
The Capex for fiber deployment can be broken up into two parts. The first part is the fiber coverage, also called fiber household passed (HHP). The second part is household connected (HHC), connecting customer households to the main fiber pass, which is also what we like to call Fiber to the Home (FTTH).
The capital expense of fiber coverage is mainly driven by the civil work (ca. 70%, with the remainder being ca. 20% to passive and ca. 10% for the active part) and relates to the distance fiber is being laid out over (yes, there is a km driver there;-). The cost can be directly related to household density. We have an economic relationship between deployment cost and the actual household density reflecting the difference in unit deployment cost between urban (i.e., high household density, least unit Capex), suburban, and rural (i.e., low household density and highest unit Capex ) urbanized areas. You need fewer kilometers to cover a given amount of households in dense urban areas than is required in a rural village with spread-out dwellings and substantially lower household density. In my economic analysis, I re-scale the fiber coverage cost to the number of households connected (i.e., the customers). Similar to household coverage cost, the household connection cost can likewise be related to the household density, which is already a measure of the connection cost. The details have been described in details in my earlier article, “The Nature of Telecom Capex.”.
The capital expenses related to fixed wireless access will, by its very nature, have a fairly large variation in its various components making up the total investment to provide fixed-like services to customer households. It will depend critically on the design criteria of the service we would like to offer (e.g., max & min speed, availability, … ) as well as the cellular network’s starting point (e.g., greenfield vs brownfield, site density, the likelihood of customer household LoS, etc..). Furthermore, supplier choice, including existing supplier lock-in and corporate purchasing power can influence the unit Capex substantially as well. Civil works and passive infrastructure is reasonably stable across western Europe, with a minor dependency on a given country’s income levels for the civil work-related cost. In my experience, the largest capital expense variation will be on the active telecom equipment depending heavily on procurement scale and supplier leverage. As I have worked in the past for a Telco which is imo&e is one of the strongest (in the industry) in terms of purchasing power and supplier leverage, there is a danger that my unitary Capex assessment may be biased towards the lower end of a reasonable estimate for an industry average for the active equipment required. Another Capex expense factor associated with substantial variation is the spectrum expense I am using in my estimate. My 5G FWA design example requires me to deploy 100 MHz at 3.x GHz (e.g., 3.4 – 3.7 GHz). I have chosen the spectrum cost to be the median of 3.x GHz European spectrum auctions from 2017 to 2023 (a total of 22 in my dataset). The auction median cost is found to be ca. 0.08 € per MHz-pop, and the interquartile range (as a measure for variation) is 0.08 € per MHz-pop. Using an average number of people per Western European household of 2.2, assuming a telco market share of 30%, and a 100 MHz bandwidth, the spectrum cost per connected household would be ca. 60 Euro (per HHC).
In general, the cost of connecting households to fiber scales directly (strongly) with the household density. The cost of connecting a household with fixed wireless access only scales very weakly with the household density (e.g., via CPA, CPE, technical support). Although, if the criteria are that FWA will have to continue to deliver a very high target speed and availability, as the household density increases, there will be substantial step function increases in the required Capex and subsequent resulting Opex. FWA TCO per connected house becomes prohibitively costly as the household density decreases, as is the case for normal cellular services as well.
The total cost of ownership (TCO) includes both the capital as well as the operational expenses relating to the technical implementation of the fixed (FTTH) and fiber-like broadband (5G FWA) service. The various components included in the TCO analysis are summarised in Figure 10.
In my analysis, I have compared the cost of implementing different FWA designs with that of connecting a household with fiber. I define a competitive 5G FWA service as a service that can provide a similar quality in terms of speed and stability as that of a GPON-based fiber connection would be able to. The fiber-to-the-home service is designed to bring up to 1 Gbps line speed to a household and could, with the right design, be extended to 10 Gbps with XGPON at a relatively low upgrade capital cost. The FWA service targets an effective speed of 300 Mbps. As household connections are added to the 5G FWA site, at some point, it would become unlikely that the targeted service level can be maintained unless substantial expansions are made to the 5G site, e.g., adding a mmWave solution with a jump in additional frequency spectrum (>100MHz). This would likely lead to additional unit Capex and increases in operational expenses (e.g., energy cost, possible technical support costs, etc..).
Assuming 6 cellular sectors for my chosen 5G FWA solution with 3 of those sectors being greenfield (e.g., abbreviated 3Si + 3Sn), Figure 11 shows that for 5G FWA at scale and targeting competitive services (in terms of quality and stability), is rarely a more economical solution (based on TCO) compared to fiber. Only at high household densities does 5G FWA become economically as attractive as fiber-to-the-home. Although the problem with 5G FWA at large household densities is, that the connection load may be too high to maintain the service design specifications, e.g., speed and availability, without substantial additional upgrades (e.g., mmWave, additional spectrum & sector densification). Even if 5G FWA on a per connected home is (much) more Capex efficient, the economics of Fiber deployment and household fiber connections are more scalable to the connected home than a fixed-like wireless service will be at low and medium household densely urbanized areas.
Relaxing the 5G FWA configuration will not help much as Figure 12 below illustrates. Only in cases where a single existing site (with 3 sectors) can offer a reasonable LoS scale to customer’s households may the TCO be brought down to a comparable range as that of fiber to the home (for a given household density, that is). Using Professor Al-Hourani results one can show that if no receiving household point (e.g., height of building + antenna) is heigher than 15 meter (max. three story buildings) the maximum amount of households with LoS should be no more than 20%. Given that in more rural and suburban environment buildings may be more likely to be a lot lower in exterior height than 15 meter (e.g., 5 – 10 meters) the number of households with LoS (from a single point) could be substantially lower than 20%. In addition, to having a LoS to a household, it, of course, also needs to be your customers premise. Say you have a market share of 30%, one should not expect within a given coverage area to have a potential of more than maybe a maximum of 6% (and likely a lot lower than that). This of course makes any dedicated 5G FWA investment prohibitedly costly due to the lack of scale.
All in all, using dedicated 5G FWA (or 4G FWA, for that matter) is unlikely to be as economical as a household fiber connection. In rural and suburban areas, where the load may be less of an issue, the existing cellular network’s intercellular distances tend to be too large to be directly usable for fiber-like services. Thus, requiring site densification. In denser urban areas, the connection load may require additional investment to support the demand and maintain quality (e.g., mmWave solutions). However, these places may also be the areas most likely already to be covered by fiber or high quality HFC.
Irrespective of FWA’s maybe poorer economics, in comparison with fiber deployment, there are many countries in Western Europe (and a lot of other places) that lack comprehensive fiber coverage in both urban, suburban and rural areas. Areas that may only be covered by mediocor xDSL services and whatever broadband mobile coverage support. Geograophical areas where fiber may only be deployed years from now if ever at all (unless encourage by EU or other non-commercial subsidies). Such under-served fiber areas may still be commercially interesting for cellular infrastructure telcos, levering existing infra, or dedicated FWA ISPs that may have gotten their hands on lower cost mmWave spectrum.
I should also point out that there is plenty of opportunity for operational expense improvements by deploying for example more intelligent power management systems and/or simply switching off-and-on antenna elements (in the deployed AAS/massive-MiMo antennas) in off-peak traffic hours. The service level that is offered to FWA customers may also be optimized by modern care solutions, e.g., AI chatbots, Apps, IVR, WiFi optimizer solutions, … reducing the need for human-human technical support interactions. However, assuming an FWA customer require a customer premise antenna, requires connectivity to indoor gateway and high quality WiFi coverage in the household, is likely to result in Opex increase in customer care.
IN THE NOW THOUGHTS
I don’t see, FWA, 5G or not, as a credible alternative for fiber to the home. It is doubtful on a household-connection basis that it economically is a better choice. The argument that there is an incredible amount of underutilized resources in our cellular networks, so why not use all that for providing fixed-like, and maybe even fiber-like, services to rural and suburban households, is trying to avoid being held responsible for having possible wasted shareholders money and value but focusing more on being the best irrespective of whether value-generating demand was present or not.
FWA and FMS are technology options that may bridge a time where fiber becomes available in a given geographical footprint. It may act as a precursor for broadband demand that can trigger an accelerate uptake of fiber broadband services once the households have been fiber covered. But its nature as a fiber-like service is likely temporary albeit it may be around for several technology refreshment cycles.
Though, the cellular industry will have to address the relative high operational costs associated with a cellular solution targeting fixed- and fiber-like broadband (and to be honest mobile broadband as well) in comparison with fiber-to-the-home Opex. The projected energy cost of 5G (and 6G for that matter) ecosystem is simply not sustainable nor should it be acceptable to the industry. While suppliers are quick to address the massive improvement in energy consumption per bit-rate per new technology generation, what really is relevant for the network economics is the absolute consumption.
Finally, In time and day, where sustainability and reduction of wasteful demand on critical resources is of incredible importance to our industry, not only for our children’s children but also for achieving favorable financing, shareholders & investors money, consumer trust (and their money month upon month), and possibly the executives self-image, its is difficult to understand why any telco would not prioritize their fiber deployment or fiber service uptake over an incredible resource demanding 5G FWA to either compete or substitute much greener or substantially more sustainable fiber-based services.
I greatly acknowledge my wife Eva Varadi, for her support, patience, and understanding during the creative process of writing this Blog. Of course, a lot of thanks go out to my former Technology and Network Economics colleagues, who have been a source of inspiration and knowledge. Special thank you to Maurice Ketel (who for many years let my Technology Economics Unit in Deutsche Telekom, I respect him above and beyond), Paul Borker, Remek Prokopik, Michael Dueser, Gudrun Bobzin, as well as many many other industry colleagues who have contributed with valuable discussions and important insights. Of course, I can also not get away with (not that I ever would) not thanking Petr Ledl (leading DTAG’s Research & Trials) and Jaroslav Holis (R&T DTAG) for their willingness and a great deal of patience with my many questions into the nature of advanced antenna systems, massive MiMo, what the performance is today and what to expect in terms of performance in the near future. Any mistakes or misrepresentations of these technologies in this article is solely due to me.
Tom Copeland & Vladimir Antikarov, “Real Options – A practitioner’s Guide”, Texere (2001). My book version is first edition. It is an excellent book, and maybe one of the best written on Real Options. However, the 1st edition is full of mistakes & errors corrected in later editions. Make sure, if you acquire this book, to choose a later than 1st edition.
Full disclosure … when I was first introduced to the concept of Network Slicing, from one of the 5G fathers that I respect immensely (Rachid, it must have been back at the end of 2014), I thought that it was one of the most useless concepts that I had heard of. I did simply not see (or get) the point of introducing this level of complexity. It did not feel right. My thoughts were that taking the slicing concept to the limit might actually not make any difference to not having it, except for a tremendous amount of orchestration and management overhead (and, of course, besides the technological fun of developing it and getting it to work).
It felt a bit (a lot, actually) as a “let’s do it because we can” thinking. With the “We can” rationale based on the maturity of cloudification and softwarization frameworks, such as cloud-native, public-cloud scale, cloud computing (e.g., edge), software-defined networks (SDN), network-function virtualization (NFV), and the-one-that-is-always-named Artificial Intelligence (AI). I believed there could be other ways to offer the same variety of service experiences without this additional (what I perceived as an unnecessary) complexity. At the time, I had reservations about its impact on network planning, operations, and network efficiency. Not at all sure, it would be a development in the right economic direction.
Since then, I have softened to the concept of Network Slicing. Not (of course) that I have much choice, as slicing is an integral part of 5G standalone (5G) implementation that will be implemented and launched over the next couple of years across our industry. Who knows, I may very likely be proven very wrong, and then I learn something.
What is a network slice? We can see a network slice as an on-user-demand logical separated network partitioning, software-defined on-top of our common physical network infrastructure (wam … what a mouthful … test me out on this one next time you see me), slicing through our network technology stack and its layers. Thinking of a virtual private network (VPN) tunnel through a transport network is a reasonably good analogy. The network slice’s logical partitioning is isolated from other traffic streams (and slices) flowing through the 5G network. Apart from the slice logical isolation, it can have many different customizations, e.g., throughput, latency, scale, Quality of Service, availability, redundancy, security, etc… The user equipment initiates the slice request from a list of pre-defined slice categories. Assuming the network is capable of supporting its requirements, the chosen slice category is then created, orchestrated, and managed through the underlying physical infrastructure that makes up the network stack. The pre-defined slice categories are designed to match what our industry believe is the most essential use-cases, e.g., (a) enhanced mobile broadband use cases (eMBB), (b) ultra-reliable low-latency communications (uRLLC) use cases, (c) massive machine-type communication (MMTC) use cases, (d) Vehicular-to-anything (V2X) use-cases, etc… While the initial (early day) applications of network slicing are expected to be fairly static and configurationally relatively simple, infrastructure suppliers (e.g., Ericsson, Huawei, Nokia, …)expect network slices to become increasingly dynamic and rich in their configuration possibilities. While slicing is typically evoked for B2B and B2B2X, there is not really a reason why consumers could not benefit from network slicing as well (e.g., gaming/VR/AR, consumer smart homes, consumer vehicular applications, etc..).
Show me the money!
Ericsson and Arthur D. Little (ADL) have recently investigated the network slicing opportunities for communications service providers (CSP). Ericsson and ADL have analyzed more than 70 external market reports on the global digitalization of industries and critically reviewed more than 400 5G / digital use cases (see references in Further Readings below). They conclude that the demand from digitalization cannot be served by CSPs without Network Slicing, e.g., “Current network resources cannot match the increasing diversity of demands over time” and “Use cases will not function” (in a conventional mobile network). Thus, according to Ericsson and ADL, the industry can not “live” without Network Slicing (I guess it is good that it comes with 5G SA then). In fact, from their study, they conclude that 30% of the 5G use cases explored would require network slicing (oh joy and good luck that it will be in our networks soon).
Ericsson and ADL find globally a network slicing business potential of 200 Billion US dollars by 2030 for CSPs. With a robust CAGR (i.e., the potential will keep growing) between 23% to 36% by 2030 (i.e., CAGR estimate for period 2025 to 2030). They find that 6 Industries segments take 90+% of the slicing potential; (1) Healthcare (23%), (2) Government (17%), (3) Transportation (15%), (4) Energy & Utilities (14%), (5) Manufacturing (12%) and (6) Media & Entertainment (11%). For the keen observer, we see that the verticals are making up for most of the slicing opportunities, with only a relatively small part being related to the consumers. It should, of course, be noted that not all CSPs are necessarily also mobile network operators (MNOs), and there are also outside the strict domain of MNOs revenue potential for non-MNO CSPs (I assume).
Let us compare this slicing opportunity to global mobile industry revenue projections from 2020 to 2030. GSMA has issued a forecast for mobile revenues until 2025, expecting a total turnover of 1,140 Billion US$ in 2025 at a CAGR (2020 – 2025) of 1.26%. Assuming this compounded annual growth rate would continue to apply, we would expect a global mobile industry revenue of 1,213 Bn US$ by 2030. Our 5G deployments will contribute in the order of 621 Bn US$ (or 51% of the total). The incremental total mobile revenue between 2020 and 2030 would be ca. 140 Bn US$ (i.e., 13% over period). If we say that roughly 20% is attributed to mobile B2B business globally, we have that by 2030 we would expect a B2B turnover of 240+ Bn US$ (an increase of ca. 30 Bn US$ over 2020). So, Ericsson & ADL’s 200 Bn US$ network slicing potential is then ca. 16% of the total 2030 global mobile industry turnover or 30+% of the 5G 2030 turnover. Of course, this assumes that somehow the slicing business potential is simply embedded in the existing mobile turnover or attributed to non-MNO CSPs (monetizing the capabilities of the MNO 5G SA slicing enablers).
Of course, the Ericsson-ADL potential could also be an actual new revenue stream untapped by today’s network infrastructures due to the lack of slicing capabilities that 5G SA will bring in the following years. If so, we can look forward to a boost of the total turnover of 16% over the GSMA-based 2030 projection. Given ca. 90% of the slicing potential is related to B2B business, it may imply that B2B mobile business would almost double due to network slicing opportunities (hmmm).
Another recent study assessed that the global 5G network slicing market will reach approximately 18 Bn US$ by 2030 with a CAGR of ca. 41% over 2020-2030.
Irrespective of the slicing turnover quantum, it is unlikely that the new capabilities of 5G SA (including network slicing and much richer granular quality of service framework) will lead to new business opportunities and enable unexplored use cases. That, in turn, may indeed lead to enhanced monetization opportunities and new revenue streams between now (2022) and 2030 for our industry.
Most Western European markets will see 5G SA being launched over the next 2 to 3 years; as 5G penetration rapidly approaches 50% penetration, I expect network slicing use cases being to be tried out with CSP/MNOs, industry partners, and governmental institutions soon after 5G SA has been launched. It should be pointed out that already for some years, slicing concepts have been trialed out in various settings. Both in 4G as well as 5G NSA networks.
Prologue to Network Slicing.
5G comes with a lot of fundamental capabilities as shown in the picture below,
5G allows for (1) enhanced mobile broadband, (2) very low latency, (3) massive increase in device density handling, i.e., massive device scale-up, (4) ultra-higher network reliability and service availability, and (5) enhanced security (not shown in the above diagram) compared to previous Gs.
The service (and thus network) requirement combinations are very high. The illustration below shows two examples of mapped-out sub-set of service (and therefore also eventually slice) requirements mapped onto the major 5G capabilities. In addition, it is quite likely that businesses would have additional requirements related to slicing performance monitoring, for example, in real-time across the network stack.
and with all the various industrial or vertical use cases (see below) one could imagine (noting that there may be many many more outside our imagination), the “fathers” of 5G became (very) concerned with how such business-critical services could be orchestrated and managed within a traditional mobile network architecture as well as across various public land mobile networks (PLMN). Much of this also comes out of the wish that 5G should “conquer” (take a slice of) next-generation industries (i.e., Industry 4.0), providing additional value above and beyond “the dumb bit pipe.” Moreover, I do believe that in parallel with the wish of becoming much more relevant to Industry 4.0 (and the next generation of verticals requirements), what also played a role in the conception of network slicing is the deeply rooted engineering concept of “control being better than trust” and that “centralized control is better than decentralized” (I lost count on this debate of centralized control vs. distributed management a long time ago).
So, yes … The 5G world is about to get a lot more complex in terms of Industrial use cases that 5G should support. And yes, our consumers will expect much higher download speeds, real-time (whatever that will mean) gaming capabilities, and “autonomous” driving …
“… it’s clear that the one shared public network cannot meet the needs of emerging and advanced mobile connectivity use cases, which have a diverse array of technical operations and security requirements.” (quote from Ericsson and Arthur D. Little study, 2021).
“The diversity of requirements will only grow more disparate between use cases — the one-size-fits-all approach to wireless connectivity will no longer suffice.” (quote from Ericsson and Arthur D. Little study, 2021).
Being a naturalist (yes, I like “naked” networks), it does seem somewhat odd (to me) to say that next generation (e.g., 5G) networks cannot support all the industrious use cases that we may throw at it in its native form. Particular after having invested billions in such networks. By partitioning a network up in limiting (logically isolated), slice instances can all be supported (allegedly). I am still in the thinking phase on that one (but I don’t think the math adds up).
Now, whether one agrees (entirely) with the economic sentiment expressed by Ericsson and ADL or not. We need a richer granular way of orchestrating and managing all those diverse use-cases we expect our 5G network to support.
So, we have (or will get) network slicing with our 5G SA Core deployment. As a reminder, when we talk about a network slice, we mean;
“An on-user-demandlogicalseparated network partitioning, software-defined, on-top of a common physical network infrastructure.”
So, the customer requested the network slice, typically via a predefined menu of slicing categories that may also have been pre-validated by the relevant network. Requested slices can also be Customized,by the requester, within the underlying 5G infrastructure capabilities and functionalities. If the network can provide the requested slicing requirements, the slice is (in theory) granted. The core network then orchestrates a logically separated network partitioning throughout the relevant infrastructure resources to comply with the requested requirements (e.g., speed, latency, device scale, coverage, security, etc…). The requested partitioning (i.e., the slice) is isolated from other slices to enable (at least on a logical level) independence of other live slices. Slice Isolation is an essential concept to network slicing. Slice Elasticity ensures that resources can be scaled up and down to ensure individual slice efficiency and an overall efficient operation of all operating slices. It is possible to have a single individual network slice or partition a slice into sub-slices with their individual requirements (that does not breach the overarching slice requirements). GSMA has issued roaming and inter-PLMN guidelines to ensure 5G network slicing inter-operability when a customer’s application finds itself outside its home -PLMN.
Today, and thanks to GSMA and ITU, there are some standard network slice services pre-defined, such as (a) eMBB – Enhanced Mobile Broadband, (b) mMTC – Massive machine-type communications, (c) URLLC – Ultra-reliable low-latency communications, (d) V2X – Vehicular-to-anything communications. These identified standard network slices are called Slice Service Types (SST). SSTs are not only limited to above mentioned 4 pre-defined slice service types. The SSTs are matched to what is called a Generic Slice Template (GST) that currently, we have 37 slicing attributes, allowing for quite a big span of combinations of requirements to be specified and validated against network capabilities and functionalities (maybe there is room for some AI/ML guidance here).
The user-requested network slice that has been set up end-2-end across the network stack, between the 5G Core and the user equipment, is called the network slice instance. The whole slice setup procedure is very well described in Chapter 12 of “5G NR and enhancements, from R15 to R16. The below illustration provides a high-level illustration of various network slices,
The 5G control function Access and Mobility management Function (AMF) is the focal point for the network slicing instances. This particular architectural choice does allow for other slicing control possibilities with a higher or lower degree of core network functionality sharing between slice instances. Again the technical details are explained well in some of the reading resources provided below. The takeaway from the above illustration is that the slice instance specifications are defined for each layer and respective physical infrastructure (e.g., routers, switches, gateways, transport device in general, etc…) of the network stack (e.g., Telco Core Cloud, Backbone, Edge Cloud, Fronthaul, New Radio, and its respective air-interface). Each telco stack layer that is part of a given network slice instance is supposed to adhere strictly to the slice requirements, enabling an End-2-End, from Core to New Radio through to the user equipment, slice of a given quality (e.g., speed, latency, jitter, security, availability, etc..).
And it may be good to keep in mind that although complex industrial use cases get a lot of attention, voice and mobile broadband could easily be set up with their own slice instances and respective quality-of-services.
Network slicing examples.
All the technical network slicing “stuff” is pretty much-taken care of by standardization and provided by the 5G infrastructure solution providers (e.g., Mavenir, Huawei, Ericsson, Nokia, etc..). Figuring the technical details of how these works require an engineering or technical background and a lot of reading.
As I see it, the challenge will be in figuring out, given a use-case, the slicing requirements and whether a single slice instance suffice or multiple are required to provide the appropriate operations and fulfillment. This, I expect, will be a challenge for both the mobile network operator as well as the business partner with the use case. This assumes that the economics will come out right for more complex (e.g., dynamic) and granular slice-instance use cases. For the operator as well as for businesses and public institutions.
The illustration below provides examples of a few (out of the 37) slicing attributes for different use cases, (a) Factories with time-critical, non-time-critical, and connected goods sub-use cases (e.g., sub-slice instances, QoS differentiated), (b) Automotive with autonomous, assisted and shared view sub-use cases, (c) Health use cases, and (d) Energy use cases.
One case that I have been studying is Networked Robotics use cases for the industrial segment. Think here about ad-hoc robotic swarms (for agricultural or security use cases) or industrial production or logistics sorting lines; below are some reflections around that.
With the emergence of the 5G Core, we will also get the possibility to apply Network slicing to many diverse use cases. That there are interesting business opportunities with network slicing, I think, is clear. Whether it will add 16% to the global mobile topline by 2030, I don’t know and maybe also somewhat skeptical about (but hey, if it does … fantastic).
Today, the type of business opportunities that network slicing brings in the vertical segments is not a very big part of a mobile operator’s core competence. Mobile operators with 5G network slicing capabilities ultimately will need to build up such competence or (and!) team up with companies that have it.
That is, if the future use cases of network slicing, as envisioned by many suppliers, ultimately will get off the ground economically as well as operationally. I remain concerned that network slicing will not make operators’ operations less complex and thus will add cost (and possible failures) to their balance sheets. The “funny” thing (IMO) is that when our 5G networks are relatively unloaded, we would not have a problem delivering the use cases (obviously). Once our 5G networks are loaded, network slicing may not be the right remedy to manage traffic pressure situations or would make the quality we are providing to consumers progressively worse (and I am not sure that business and value-wise, this is a great thing to do). Of course, 6G may solve all those concerns 😉
I greatly acknowledge my wife, Eva Varadi, for her support, patience, and understanding during the creative process of writing this Blog. Also, many of my Deutsche Telekom AG and Industry colleagues, in general, have in countless ways contributed to my thinking and ideas leading to this little Blog. Thank you!
Jia Shen, Zhongda Du, & Zhi Zhang, “5G NR and enhancements, from R15 to R16”, Elsevier Science, (2021). Provides a really good overview of what to expect from 5G standalone. Chapter 12 provides a good explanation of (and in detail account for) how 5G Network Slicing works in detail. Definitely one of my favorite books on 5G, it is not “just” an ANRA.
GSMA, “Securing the 5G Era” (2021). A good overview of security principles in 5G and how previous vulnerabilities in previous cellular generations are being addressed in 5G. This includes some explanation on why slicing further enhances security.
By the end of 2020, according with Ericsson, it was estimated that there where ca. 7.6 million 5G subscriptions in Western Europe (~ 1%). Compare this to North America’s ca. 14 million (~4%) and 190 million (~11%) North East Asia (e.g, China, South Korea, Japan, …).
Maybe Western Europe is not doing that great, when it comes to 5G penetration, in comparison with other big regional markets around the world. To some extend the reason may be that 4G network’s across most of Western Europe are performing very well and to an extend more than servicing consumers demand. For example, in The Netherlands, consumers on T-Mobile’s 4G gets, on average, a download speed of 100+ Mbps. About 5× the speed you on average would get in USA with 4G.
From the October 2021 statistics of the Global mobile Suppliers Association (GSA), 180 operators worldwide (across 72 countries) have already launched 5G. With 37% of those operators actively marketing 5G-based Fixed Wireless Access (FWA) to consumers and businesses. There are two main 5G deployment flavors; (a) non-standalone (NSA) deployment piggybacking on top of 4G. This is currently the most common deployment model, and (b) as standalone (SA) deployment, independently from legacy 4G. The 5G SA deployment model is to be expected to become the most common over the next couple of years. As of October 2021, 15 operators have launched 5G SA. It should be noted that, operators with 5G SA launched are also likely to support 5G in NSA mode as well, to provide 5G to all customers with a 5G capable handset (e.g., at the moment only 58% of commercial 5G devices supports 5G SA). Only reason for not supporting both NSA and SA would be for a greenfield operator or that the operator don’t have any 4G network (none of that type comes to my mind tbh). Another 25 operators globally are expected to be near launching standalone 5G.
It should be evident, also from the illustration below, that mobile customers globally got or will get a lot of additional download speed with the introduction of 5G. As operators introduce 5G, in their mobile networks, they will leapfrog their available capacity, speed and quality for their customers. For Europe in 2021 you would, with 5G, get an average downlink (DL) speed of 154 ± 90 Mbps compared to 2019 4G DL speed of 26 ± 8 Mbps. Thus, with 5G, in Europe, we have gained a whooping 6× in DL speed transitioning from 4G to 5G. In Asia Pacific, the quality gain is even more impressive with a 10× in DL speed and somewhat less in North America with 4× in DL speed. In general, for 5G speeds exceeding 200 Mbps on average may imply that operators have deployed 5G in the C-band band (e.g., with the C-band covering 3.3 to 5.0 GHz).
The above DL speed benchmark (by Opensignal) gives a good teaser for what to come and to expect from 5G download speed, once a 5G network is near you. There is of course much more to 5G than downlink (and uplink) speed. Some caution should be taken in the above comparison between 4G (2019) and 5G (2021) speed measurements. There are still a fair amount of networks around the world without 5G or only started upgrading their networks to 5G. I would expect the 5G average speed to reduce a bit and the speed variance to narrow as well (i.e., performance becoming more consistent).
In a previous blog I describe what to realistically expect from 5G and criticized some of the visionary aspects of the the original 5G white paper paper published back in February 2015. Of course, the tech-world doesn’t stand still and since the original 5G visionary paper by El Hattachi and Erfanian. 5G has become a lot more tangible as operators deploy it or is near deployment. More and more operators have launched 5G on-top of their 4G networks and in the configuration we define as non-standalone (i.e., 5G NSA). Within the next couple of years, coinciding with the access to higher frequencies (>2.1 GHz) with substantial (unused or underutilized) spectrum bandwidths of 50+ MHz, 5G standalone (SA) will be launched. Already today many high-end handsets support 5G SA ensuring a leapfrog in customer experience above and beyond shear mobile broadband speeds.
The below chart illustrates what to expect from 5G SA, what we already have in the “pocket” with 5G NSA, and how that may compare to existing 4G network capabilities.
There cannot be much doubt that with the introduction of the 5G Core (5GC) enabling 5G SA, we will enrich our capability and service-enabler landscape. Whether all of this cool new-ish “stuff” we get with 5G SA will make much top-line sense for operators and convenience for consumers at large is a different story for a near-future blog (so stay tuned). Also, there should not be too much doubt that 5G NSA already provide most of what the majority of our consumers are looking for (more speed).
Overall, 5G SA brings benefits, above and beyond NSA, on (a) round-trip delay (latency) which will be substantially lower in SA, as 5G does not piggyback on the slower 4G, enabling the low latency in ultra-reliable low latency communications (uRLLC), (b) a factor of 250× improvement device density (1 Million devices per km2) that can be handled supporting massive machine type communication scenarios (mMTC), (c) supports communications services at higher vehicular speeds, (d) in theory should result in low device power consumption than 5G NSA, and (e) enables new and possible less costly ways to achieve higher network (and connection) availability (e.g., with uRLLC).
Compared to 4G, 5G SA brings with it a more flexible, scalable and richer set of quality of service enablers. A 5G user equipment (UE) can have up to 1,024 so called QoS flows versus a 4G UE that can support up to 8 QoS classes (tied into the evolved packet core bearer). The advantage of moving to 5G SA is a significant reduction of QoS driven signaling load and management processing overhead, in comparison to what is the case in a 4G network. In 4G, it has been clear that the QoS enablers did not really match the requirements of many present day applications (i.e., brutal truth maybe is that the 4G QoS was outdated before it went live). This changes with the introduction of 5G SA.
So, when is it a good idea to implement 5G Standalone for mobile operators?
There are maybe three main events that should trigger operators to prepare for and launch 5G SA;
Economical demand for what 5G SA offers.
Critical mass of 5G consumers.
Want to claim being the first to offer 5G SA.
with the 3rd point being the least serious but certainly not an unlikely factor in deploying 5G SA. Apart from potentially enriching consumers experience, there are several operational advantages of transitioning to a 5GC, such as more mature IT-like cloudification of our telecommunications networks (i.e., going telco-cloud native) leading to (if designed properly) a higher degree of automation and autonomous network operations. Further, it may also allow the braver parts of telco-land to move a larger part of its network infrastructure capabilities into the public-cloud domain operated by hyperscalers or network-cloud consortia’s (if such entities will appear). Another element of the 5G SA cloud nativification (a new word?) that is frequently not well considered, is that it will allow operators to start out (very) small and scale up as business and consumer demand increases. I would expect that particular with hyperscalers and of course the-not-so-unusual-telco-supplier-suspects (e.g., Ericsson, Nokia, Huawei, Samsung, etc…), operators could launch fairly economical minimum viable products based on a minimum set of 5G SA capabilities sufficient to provide new and cost-efficient services. This will allow early entry for business-to-business new types of QoS and (or) slice-based services based on our new 5G SA capabilities.
Western Europe mobile market expectations – 5G technology share.
By end of 2021, it is expected that Western Europe would have in the order of 36 Million 5G connections, around a 5% 5G penetration. Increasing to 80 Million (11%) by end of 2022. By 2024 to 2025, it is expected that 50% of all mobile connections would be 5G based. As of October 2021 ca. 58% of commercial available mobile devices supports already 5G SA. This SA share is anticipated to grow rapidly over the next couple of years making 5G NSA increasingly unimportant.
Approaching 50% of all connections being 5G appears a very good time to aim having 5G standalone implemented and launched for operators. Also as this may coincide with substantial efforts to re-farming existing frequency spectrum from 4G to 5G as 5G data traffic exceeds that of 4G.
For Western Europe 2021, ca. 18% of the total mobile connections are business related. This number is expected to steadily increase to about 22% by 2030. With the introduction of new 5G SA capabilities, as briefly summarized above, it is to be expected that the 5G business connection share quickly will increase to the current level and that business would be able to directly monetize uRLLC, mMTC and the underlying QoS and network slicing enablers. For consumers 5G SA will bring some additional benefits but maybe less obvious new monetization possibilities, beyond the proportion of consumers caring about latency (e.g., gamers). Though, it appears likely that the new capabilities could bring operators efficiency opportunities leading to improved margin earned on consumers (for another article).
Learn as much as possible from recent IT cloudification journeys (e.g., from monolithic to cloud, understand pros and cons with lift-and-shift strategies and the intricacies of operating cloud-native environments in public cloud domains).
Aim to have 5GC available for 5G SA launch latest by 2024.
Run 5GC minimum viable product poc’s with friendly (business) users prior to bigger launch.
As 5G is launched on C-band / 3.x GHz it may likewise be a good point in time to have 5G SA available. At least for B2B customers that may benefit from uRLLC, lower latency in general, mMTC, a much richer set of QoS, network slicing, etc…
Having a solid 4G to 5G spectrum re-farming strategy ready between now and 2024 (too late imo). This should map out 4G+NSA and SA supply dynamics as increasingly customers get 5G SA capabilities in their devices.
Western Europe mobile market expectations – traffic growth.
With the growth of 5G connections and the expectation that 5G would further boost the mobile data consumption, it is expected that by 2023 – 2024, 50% of all mobile data traffic in Western Europe would be attributed to 5G. This is particular driven by increased rollout of 3.x GHz across the Western European footprint and associated massive MiMo (mMiMo) antenna deployments with 32×32 seems to be the telco-lands choice. In blended mobile data consumption a CAGR of around 34% is expected between 2020 and 2030, with 2030 having about 26× more mobile data traffic than that of 2020. Though, I suspect that in Western Europe, aggressive fiberization of telecommunications consumer and business markets, over the same period, may ultimately slow the growth (and demand) on mobile networks.
A typical Western European operator would have between 80 – 100+ MHz of bandwidth available for 4G its downlink services. The bandwidth variation being determined by how much is required of residual 3G and 2G services and whether the operator have acquired 1500MHz SDL (supplementary downlink) spectrum. With an average 4G antenna configuration of 4×4 MiMo and effective spectral efficiency of 2.25 Mbps/MHz/sector one would expect an average 4G downlink speed of 300+ Mbps per sector (@ 90 MHz committed to 4G). For 5G SA scenario with 100 MHz of 3.x GHz and 2×10 MHz @ 700 MHz, we should expect an average downlink speed of 500+ Mbps per sector for a 32×32 massive MiMo deployment at same effective spectral efficiency as 4G. In this example, although naïve, quality of coverage is ignored. With 5G, we more than double the available throughput and capacity available to the operator. So the question is whether we remain naïve and don’t care too much about the coverage aspects of 3.x GHz, as beam-forming will save the day and all will remain cheesy for our customers (if something sounds too good to be true, it rarely is true).
In an urban environment it is anticipated that with beam-forming available in our mMiMo antenna solutions downlink coverage will be reasonably fine (i.e., on average) with 3.x GHz antennas over-layed on operators existing macro-cellular footprint with minor densification required (initially). In the situation that 3.x GHz uplink cannot reach the on-macro-site antenna, the uplink can be closed by 5G @ 700 MHz, or other lower cellular frequencies available to the operator and assigned to 5G (if in standalone mode). Some concerns have been expressed in literature that present advanced higher order antenna’s (e.g., 16×16 and above ) will on average provide a poorer average coverage quality over a macro cellular area than what consumers would be used to with lower order antennas (e.g., 4×4 or lower) and that the only practical (at least with today’s state of antennas) solution would be sectorization to make up for beam forming shortfalls. In rural and sub-urban areas advanced antennas would be more suitable although the demand would be a lot less than in a busy urban environment. Of course closing the 3.x GHz with existing rural macro-cellular footprint may be a bigger challenge than in an urban clutter. Thus, massive MiMo deployments in rural areas may be much less economical and business case friendly to deploy. As more and more operators deploy 3.x GHz higher-order mMiMo more field experience will become available. So stay tuned to this topic. Although I would reserve a lot more CapEx in my near-future budget plans for substantial more sectorization in urban clutter than what I am sure is currently in most operators plans. Maybe in rural and suburban areas the need for sectorizations would be much smaller but then densification may be needed in order to provide a decent 3.x GHz coverage in general.
Western Europe mobile market expectations – 5G RAN Capex.
That brings us to another important aspect of 5G deployment, the Radio Access Network (RAN) capital expenditures (CapEx). Using my own high-level (EU-based) forecast model based on technology deployment scenario per Western European country that in general considers 1 – 3% growth in new sites per anno until 2024, then from 2025 onwards, I assuming 2 – 5% growth due to densifications needs of 5G, driven by traffic growth and before mentioned coverage limitations of 3.x GHz. Exact timing and growth percentages depends on initial 5G commercial launch, timing of 3.x GHz deployment, traffic density (per site), and site density considering a country’s surface area.
According with Statista, Western Europe had in 2018 a cellular site base of 421 thousands. Further, Statista expected this base will grow with 2% per anno in the years after 2018. This gives an estimated number of cellular sites of 438k in 2020 that has been assumed as a starting point for 2020. The model estimates that by 2030, over the next 10 years, an additional 185k (+42%) sites will have been built in Western Europe to support 5G demand. 65% (120+k) of the site growth, over the next 10 years, will be in Germany, France, Italy, Spain and UK. All countries with relative larger geographical areas that are underserved with mobile broadband services today. Countries with incumbent mobile networks, originally based on 900 MHz GSM grids (of course densified since the good old GSM days), and thus having coarser cellular grids with higher degree of mismatching the higher 5G cellular frequencies (i.e., ≥ 2.5 GHz). In the model, I have not accounted for an increased demand of sectorizations to keep coverage quality upon higher order mMiMO deployments. This, may introduce some uncertainty in the Capex assessment. However, I anticipate that sectorization uncertainty may be covered in the accelerated site demand the last 5 years of the period.
In the illustration above, the RAN capital investment assumes all sites will eventually be fiberized by 2025. That may however be an optimistic assumption and for some countries, even in Western Europe, unrealistic and possibly highly uneconomical. New sites, in my model, are always fiberized (again possibly too optimistic). Miscellaneous (Misc.) accounts for any investments needed to support the RAN and Fiber investments (e.g., Core, Transport, Cap. Labor, etc..).
In the economical estimation price erosion has been taken into account. This erosion is a blended figure accounting for annual price reduction on equipment and increases in labor cost. I am assuming a 5-year replacement cycle with an associated 10% average price increase every 5 years (on the previous year’s eroded unit price). This accounts for higher capability equipment being deployed to support the increased traffic and service demand. The economical justification for the increase unit price being that otherwise even more new sites would be required than assumed in this model. In my RAN CapEx projection model, I am assuming rational deployment, that is demand driven deployment. Thus, operators investments are primarily demand driven, e.g., only deploying infrastructure required within a given financial recovery period (e.g., depreciation period). Thus, if an operator’s demand model indicate that it will need a given antenna configuration within the financial recovery period, it deploys that. Not a smaller configuration. Not a bigger configuration. Only the one required by demand within the financial recovery period. Of course, there may be operators with other deployment incentives than pure demand driven. Though on average I suspect this would have a neglectable effect on the scale of Western Europe (i.e., on average Western Europe Telco-land is assumed to be reasonable economically rational).
All in all, demand over the next 8 years leads to an 80+ Billion Euro RAN capital expenditure, required between 2022 and 2030. This, equivalent to a annual RAN investment level of a bit under 10 Billion Euro. The average RAN CapEx to Mobile Revenue over this period would be ca. 6.3%, which is not a shockingly high level (tbh), over a period that will see an intense rollout of 5G at increasingly higher frequencies and increasingly capable antenna configurations as demand picks up. Biggest threat to capital expenditures is poor demand models (or no demand models) and planning processes investing too much too early, ultimately resulting in buyers regret and cycled in-efficient investment levels over the next 10 years. And for the reader still awake and sharp, please do note that I have not mentioned the huge elephant in the room … The associated incremental operational expense (OpEx) that such investments will incur.
As mobile revenues are not expected to increase over the period 2022 to 2030, this leaves 5G investments main purpose to maintaining current business level dominated by consumer demand. I hope this scenario will not materialize. Given how much extra quality and service potential 5G will deliver over the next 10 years, it seems rather pessimistic to assume that our customers would not be willing to pay more for that service enhancement that 5G will brings with it. Alas, time will show.
I greatly acknowledge my wife Eva Varadi for her support, patience and understanding during the creative process of writing this Blog. Petr Ledl, head of DTAG’s Research & Trials, and his team’s work has been a continuous inspiration to me (thank you so much for always picking up on that phone call Petr!). Also many of my Deutsche Telekom AG, T-Mobile NL & Industry colleagues in general have in countless of ways contributed to my thinking and ideas leading to this little Blog. Thank you!
Rachid El Hattachi & Javan Erfanian , “5G White Paper”, NGMN Alliance, (February 2015). See also “5G White Paper 2” by Nick Sampson (Orange), Javan Erfanian (Bell Canada) and Nan Hu (China Mobile).
Global Mobile Frequencies Database. (last update, 25 May 2021). I recommend very much to subscribe to this database (€595,. single user license). Provides a wealth of information on spectrum portfolios across the world.
Jia Shen, Zhongda Du, & Zhi Zhang, “5G NR and enhancements, from R15 to R16”, Elsevier Science, (2021). Provides a really good overview of what to expect from 5G standalone. Particular, very good comparison with what is provided with 4G and the differences with 5G (SA and NSA).
Ali Zaidi, Fredrik Athley, Jonas Medbo, Ulf Gustavsson, Giuseppe Durisi, & Xiaoming Chen, “5G Physical Layer Principles, Models and Technology Components”, Elsevier Science, (2018). The physical layer will always pose a performance limitation on a wireless network. Fundamentally, the amount of information that can be transferred between two locations will be limited by the availability of spectrum, the laws of electromagnetic propagation, and the principles of information theory. This book provides a good description of the 5G NR physical layer including its benefits and limitations. It provides a good foundation for modelling and simulation of 5G NR.
Thomas L. Marzetta, Erik G. Larsson, Hong Yang, Hien Quoc Ngo, “Fundamentals of Massive MIMO”, Cambridge University Press, (2016). Excellent account of the workings of advanced antenna systems such as massive MiMo.
Western Europe: Western Europe has a bit of a fluid definition (I have found), here Western Europe includes the following countries comprising a population of ca. 425 Million people (in 2021); Austria, Belgium, Denmark, Finland, France, Germany, Greece, Ireland, Italy, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland United Kingdom, Andorra, Cyprus, Faeroe Islands, Greenland, Guernsey, Jersey, Malta, Luxembourg, Monaco, Liechtenstein, San Marino, Gibraltar.
100% 5G coverage is not going to happen with 30 – 300 GHz millimeter-wave frequencies alone.
The “NGMN 5G white paper” , which I will in the subsequent parts refer to as the 5G vision paper, require the 5G coverage to be 100%.
At 100% cellular coverage it becomes somewhat academic whether we talk about population coverage or geographical (area) coverage. The best way to make sure you cover 100% of population is covering 100% of the geography. Of course if you cover 100% of the geography, you are “reasonably” ensured to cover 100% of the population.
While it is theoretically possible to cover 100% (or very near to) of population without covering 100% of the geography, it might be instructive to think why 100% geographical coverage could be a useful target in 5G;
Network-augmented driving and support for varous degrees of autonomous driving would require all roads to be covered (however small).
Internet of Things (IoT) Sensors and Actuators are likely going to be of use also in rural areas (e.g., agriculture, forestation, security, waterways, railways, traffic lights, speed-detectors, villages..) and would require a network to connect to.
Given many users personal area IoT networks (e.g., fitness & health monitors, location detection, smart-devices in general) ubiquitous becomes essential.
Internet of flying things (e.g., drones) are also likely to benefit from 100% area and aerial coverage.
However, many countries remain lacking in comprehensive geographical coverage. Here is an overview of the situation in EU28 (as of 2015);
For EU28 countries, 14% of all house holds in 2015 still had no LTE coverage. This was approx.30+ million households or equivalent to 70+ million citizens without LTE coverage. The 14% might seem benign. However, it covers a Rural neglect of 64% of households not having LTE coverage. One of the core reasons for the lack of rural (population and household) coverage is mainly an economic one. Due to the relative low number of population covered per rural site and compounded by affordability issues for the rural population, overall rural sites tend to have low or no profitability. Network sharing can however improve the rural site profitability as site-related costs are shared.
From an area coverage perspective, the 64% of rural households in EU28 not having LTE coverage is likely to amount to a sizable lack of LTE coverage area. This rural proportion of areas and households are also very likely by far the least profitable to cover for any operator possibly even with very progressive network sharing arrangements.
Fixed broadband, Fiber to the Premises (FTTP) and DOCSIS3.0, lacks further behind that of mobile LTE-based broadband. Maybe not surprisingly from an business economic perspective, in rural areas fixed broadband is largely unavailable across EU28.
The chart below illustrates the variation in lack of broadband coverage across LTE, Fiber to the Premises (FTTP) and DOCSIS3.0 (i.e., Cable) from a total country perspective (i.e., rural areas included in average).
We observe that most countries have very far to go on fixed broadband provisioning (i.e., FTTP and DOCSIS3.0) and even on LTE coverage lacks complete coverage. The rural coverage view (not shown here) would be substantially worse than the above Total view.
The 5G ambition is to cover 100% of all population and households. Due to the demographics of how rural households (and populations) are spread, it is also likely that fairly large geographical areas would need to be covered in order to come true on the 100% ambition.
It would appear that bridging this lack of broadband coverage would be best served by a cellular-based technology. Given the fairly low population density in such areas relative higher average service quality (i.e., broadband) could be delivered as long as the cell range is optimized and sufficient spectrum at a relative low carrier frequency (< 1 GHz) would be available. It should be remembered that the super-high 5G 1 – 10 Gbps performance cannot be expected in rural areas. Due to the lower carrier frequency range need to provide economic rural coverage both advanced antenna systems and very large bandwidth (e.g., such as found in the mm-frequency range) would not be available to those areas. Thus limiting the capacity and peak performance possible even with 5G.
I would suspect that irrespective of the 100% ambition, telecom providers would be challenged by the economics of cellular deployment and traffic distribution. Rural areas really sucks in profitability, even in fairly aggressive sharing scenarios. Although multi-party (more than 2) sharing might be a way to minimize the profitability burden on deep rural coverage.
The above chart shows the relationship between traffic distribution and sites. As a rule of thumb 50% of revenue is typically generated by 10% of all sites (i.e., in a normal legacy mobile network) and approx. 50% of (rural) sites share roughly 10% of the revenue. Note: in emerging markets the distribution is somewhat steeper as less comprehensive rural coverage typically exist. (Source:The ABC of Network Sharing – The Fundamentals.).
Irrespective of my relative pessimism of the wider coverage utility and economics of millimeter-wave (mm-wave) based coverage, there shall be no doubt that mm-wave coverage will be essential for smaller and smallest cell coverage where due to density of users or applications will require extreme (in comparison to today’s demand) data speeds and capacities. Millimeter-wave coverage-based architectures offer very attractive / advanced antenna solutions that further will allow for increased spectral efficiency and throughput. Also the possibility of using mm-wave point to multipoint connectivity as last mile replacement for fiber appears very attractive in rural and sub-urban clutters (and possible beyond if the cost of the electronics drop according the expeced huge increase in demand for such). This last point however is in my opinion independent of 5G as Facebook with their Terragraph development have shown (i.e., 60 GHz WiGig-based system). A great account for mm-wave wireless communications systems can be found in T.S. Rappaport et al.’s book “Millimeter Wave Wireless Communications” which not only comprises the benefits of mm-wave systems but also provides an account for the challenges. It should be noted that this topic is still a very active (and interesting) research area that is relative far away from having reached maturity.
In order to provide 100% 5G coverage for the mass market of people & things, we need to engage the traditional cellular frequency bands from 600 MHz to 3 GHz.
1 – 10 Gbps PEAK DATA RATE PER USER.
Getting a Giga bit per second speed is going to require a lot of frequency bandwidth, highly advanced antenna systems and lots of additional cells. And that is likely going to lead to a (very) costly 5G deployment. Irrespective of the anticipated reduced unit cost or relative cost per Byte or bit-per-second.
At 1 Gbps it would take approx. 16 seconds to download a 2 GB SD movie. It would take less than a minute for the HD version (i.e., at 10 Gbps it just gets better;-). Say you have a 16GB smartphone, you loose maybe up to 20+% for the OS, leaving around 13GB for things to download. With 1Gbps it would take less than 2 minutes to fill up your smartphones storage (assuming you haven’t run out of credit on your data plan or reached your data ceiling before then … of course unless you happen to be a customer of T-Mobile US in which case you can binge on = you have no problems!).
The biggest share of broadband usage comes from video streaming which takes up 60% to 80% of all volumetric traffic pending country (i.e., LTE terminal penetration dependent). Providing higher speed to your customer than is required by the applied video streaming technology and smartphone or tablet display being used, seems somewhat futile to aim for. The Table below provides an overview of streaming standards, their optimal speeds and typical viewing distance for optimal experience;
So … 1Gbps could be cool … if we deliver 32K video to our customers end device, i.e., 750 – 1600 Mbps optimal data rate. Though it is hard to see customers benefiting from this performance boost given current smartphone or tablet display sizes. The screen size really have to be ridiculously large to truly benefit from this kind of resolution. Of course Star Trek-like full emersion (i.e., holodeck) scenarios would arguably require a lot (=understatement) bandwidth and even more (=beyond understatement) computing power … though such would scenario appears unlikely to be coming out of cellular devices (even in Star Trek).
1 Gbps fixed broadband plans have started to sell across Europe. Typically on Fiber networks although also on DOCSIS3.1 (10Gbps DS/1 Gbps US) networks as well in a few places. It will only be a matter of time before we see 10 Gbps fixed broadband plans being offered to consumers. Irrespective of compelling use cases might be lacking it might at least give you the bragging rights of having the biggest.
From European Commissions “Europe’s Digital Progress Report 2016”, 22 % of European homes subscribe to fast broadband access of at least 30 Mbps. An estimated 8% of European households subscribe to broadband plans of at least 100 Mbps. It is worth noticing that this is not a problem with coverage as according with the EC’s “Digital Progress Report” around 70% of all homes are covered with at least 30 Mbps and ca. 50% are covered with speeds exceeding 100 Mbps.
The chart below illustrates the broadband speed coverage in EU28;
Even if 1Gbps fixed broadband plans are being offered, still majority of European homes are at speeds below the 100 Mbps. Possible suggesting that affordability and household economics plays a role as well as the basic perceived need for speed might not (yet?) be much beyond 30 Mbps?
Most aggregation and core transport networks are designed, planned, built and operated on a assumption of dominantly customer demand of lower than 100 Mbps packages. As 1Gbps and 10 Gbps gets commercial traction, substantial upgrades are require in aggregation, core transport and last but not least possible also on an access level (to design shorter paths). It is highly likely distances between access, aggregation and core transport elements are too long to support these much higher data rates leading to very substantial redesigns and physical work to support this push to substantial higher throughputs.
Most telecommunications companies will require very substantial investments in their existing transport networks all the way from access to aggregation through the optical core switching networks, out into the world wide web of internet to support 1Gbps to 10 Gbps. Optical switching cards needs to be substantially upgraded, legacy IP/MPLS architectures might no longer work very well (i.e., scale & complexity issue).
Most analysts today believe that incumbent fixed & mobile broadband telecommunications companies with a reasonable modernized transport network are best positioned for 5G compared to mobile-only operators or fixed-mobile incumbents with an aging transport infrastructure.
What about the state of LTE speeds across Europe? OpenSignal recurrently reports on the State of LTE, the following summarizes LTE speeds in Mbps as of June 2017 for EU28 (with the exception of a few countries not included in the OpenSignal dataset);
The OpenSignal measurements are based on more than half a million devices, almost 20 billion measurements over the period of the 3 first month of 2017.
The 5G speed ambition is by todays standards 10 to 30+ times away from present 2016/2017 household fixed broadband demand or the reality of provided LTE speeds.
In essence, I can provide very high data rates in bits per second by providing a lot of frequency bandwidth B, use the most spectrally efficient technologies maximizing η, and/or add as many cells N that my economics allow for.
The average spectral efficiency is expected to be coming out in the order of 10 Mbps/MHz/cell using advanced receiver architectures, multi-antenna, multi-cell transmission and corporation. So pretty much all the high tech goodies we have in the tool box is being put to use of squeezing out as many bits per spectral Hz available and in a sustainable matter. Under very ideal Signal to Noise Ratio conditions, massive antenna arrays of up to 64 antenna elements (i.e., an optimum) seems to indicate that 50+ Mbps/MHz/Cell might be feasible in peak.
So for a spectral efficiency of 10 Mbps/MHz/cell and a demanded 1 Gbps data rate we would need 100 MHz frequency bandwidth per cell (i.e., using the above formula). Under very ideal conditions and relative large antenna arrays this might lead to a spectral requirement of only 20 MHz at 50 Mbps/MHz/Cell. Obviously, for 10 Gbps data rate we would require 1,000 MHz frequency bandwidth (1 GHz!) per cell at an average spectral efficiency of 10 Mbps/MHz/cell.
The spectral efficiency assumed for 5G heavily depends on successful deployment of many-antenna segment arrays (e.g., Massive MiMo, beam-forming antennas, …). Such fairly complex antenna deployment scenarios work best at higher frequencies, typically above 2GHz. Also such antenna systems works better at TDD than FDD with some margin on spectral efficiency. These advanced antenna solutions works perfectly in the millimeter wave range (i.e., ca. 30 – 300 GHz) where the antenna segments are much smaller and antennas can be made fairly (very) compact (note: resonance frequency of the antenna proportional to half the wavelength with is inverse proportional to the carrier frequency and thus higher frequencies need smaller material dimension to operate).
Below 2 GHz higher-order MiMo becomes increasingly impractical and the spectral efficiency regress to the limitation of a simple single-path antenna. Substantially lower than what can be achieved at much high frequencies with for example massive-MiMo.
So for the 1Gbps to 10 Gbps data rates to work out we have the following relative simple rationale;
High data rates require a lot of frequency bandwidth (>100 MHz to several GHz per channel).
Lots of frequency bandwidth are increasingly easier to find at high and very high carrier frequencies (i.e., why millimeter wave frequency band between 30 – 300 GHz is so appealing).
High and very high carrier frequencies results in small, smaller and smallest cells with very high bits per second per unit area (i.e., the area is very small!).
High and very high carrier frequency allows me to get the most out of higher order MiMo antennas (i.e., with lots of antenna elements),
Due to fairly limited cell range, I boost my overall capacity by adding many smallest cells (i.e., at the highest frequencies).
We need to watch out for the small cell densification which tends not to scale very well economically. The scaling becomes a particular problem when we need hundreds of thousands of such small cells as it is expected in most 5G deployment scenarios (i.e., particular driven by the x1000 traffic increase). The advanced antenna systems required (including the computation resources needed) to max out on spectral efficiency are likely going to be one of the major causes of breaking the economical scaling. Although there are many other CapEx and OpEx scaling factors to be concerned about for small cell deployment at scale.
Further, for mass market 5G coverage, as opposed to hot traffic zones or indoor solutions, lower carrier frequencies are needed. These will tend to be in the usual cellular range we know from our legacy cellular communications systems today (e.g., 600 MHz – 2.1 GHz). It should not be expected that 5G spectral efficiency will gain much above what is already possible with LTE and LTE-advanced at this legacy cellular frequency range. Sheer bandwidth accumulation (multi-frequency carrier aggregation) and increased site density is for the lower frequency range a more likely 5G path. Of course mass market 5G customers will benefit from faster reaction times (i.e., lower latencies), higher availability, more advanced & higher performing services arising from the very substantial changes expected in transport networks and data centers with the introduction of 5G.
Last but not least to this story … 80% and above of all mobile broadband customers usage, data as well as voice, happens in very few cells (e.g., 3!) … representing their Home and Work.
As most of the mobile cellular traffic happen at the home and at work (i.e., thus in most cases indoor) there are many ways to support such traffic without being concerned about the limitation of cell ranges.
The giga bit per second cellular service is NOT a service for the mass market, at least not in its macro-cellular form.
≤ 1 ms IN ROUND-TRIP DELAY.
A total round-trip delay of 1 or less millisecond is very much attuned to niche service. But a niche service that nevertheless could be very costly for all to implement.
Speed of light travels ca. 300 km per millisecond (ms) in vacuum and approx. 210 km per ms in fiber (some material dependency here). Lately engineers have gotten really excited about the speed of light not being fast enough and have made a lot of heavy thinking abou edge this and that (e.g., computing, cloud, cloudlets, CDNs,, etc…). This said it is certainly true that most modern data centers have not been build taking too much into account that speed of light might become insufficient. And should there really be a great business case of sub-millisecond total (i.e., including the application layer) roundtrip time scales edge computing resources would be required a lot closer to customers than what is the case today.
It is common to use delay, round-trip time or round-trip delay, or latency as meaning the same thing. Though it is always cool to make sure people really talk about the same thing by confirming that it is indeed a round-trip rather than single path. Also to be clear it is worthwhile to check that all people around the table talk about delay at the same place in the OSI stack or network path or whatever reference point agreed to be used.
In the context of the 5G vision paper it is emphasized that specified round-trip time is based on the application layer (i.e., OSI model) as reference point. It is certainly the most meaningful measure of user experience. This is defined as the End-2-End (E2E) Latency metric and measure the complete delay traversing the OSI stack from physical layer all the way up through network layer to the top application layer, down again, between source and destination including acknowledgement of a successful data packet delivery.
The 5G system shall provide 10 ms E2E latency in general and 1 ms E2E latency for use cases requiring extremely low latency.
The 5G vision paper states “Note these latency targets assume the application layer processing time is negligible to the delay introduced by transport and switching.” (Section 4.1.3 page 26 in “NGMN 5G White paper”).
In my opinion it is a very substantial mouthful to assume that the Application Layer (actually what is above the Network Layer) will not contribute significantly to the overall latency. Certainly for many applications residing outside the operators network borders, in the world wide web, we can expect a very substantial delay (i.e., even in comparison with 10 ms). Again this aspect was also addressed in my two first chapters.
Very substantial investments are likely needed to meet E2E delays envisioned in 5G. In fact the cost of improving latencies gets prohibitively more expensive as the target is lowered. The overall cost of design for 10 ms would be a lot less costly than designing for 1 ms or lower. The network design challenge if 1 millisecond or below is required, is that it might not matter that this is only a “service” needed in very special situations, overall the network would have to be designed for the strictest denominator.
Moreover, if remedies needs to be found to mitigate likely delays above the Network Layer, distance and insufficient speed of light might be the least of worries to get this ambition nailed (even at the 10 ms target). Of course if all applications are moved inside operator’s networked premises with simpler transport paths (and yes shorter effective distances) and distributed across a hierarchical cloud (edge, frontend, backend, etc..), the assumption of negligible delay in layers above the Network Layer might become much more likely. However, it does sound a lot like America Online walled garden fast forward to the past kind of paradigm.
So with 1 ms E2E delay … yeah yeah … “play it again Sam” … relevant applications clearly need to be inside network boundary and being optimized for processing speed or silly & simple (i.e., negligible delay above the Network Layer), no queuing delay (to the extend of being in-efficiency?), near-instantaneous transmission (i.e., negligible transmission delay) and distances likely below tenth of km (i.e., very short propagation delay).
When the speed of light is too slow there are few economic options to solve that challenge.
≥ 10,000 Gbps / Km2 DATA DENSITY.
The data density is maybe not the most sensible measure around. If taken too serious could lead to hyper-ultra dense smallest network deployments.
This has always been a fun one in my opinion. It can be a meaningful design metric or completely meaningless.
There is of course nothing particular challenging in getting a very high throughput density if an area is small enough. If I have a cellular range of few tens of meters, say 20 meters, then my cell area is smaller than 1/1000 of a km2. If I have 620 MHz bandwidth aggregated between 28 GHz and 39 GHz (i.e., both in the millimeter wave band) with a 10 Mbps/MHz/Cell, I could support 6,200 Gbps/km2. That’s almost 3 Petabyte in an hour or 10 years of 24/7 binge watching of HD videos. Note given my spectral efficiency is based on an average value, it is likely that I could achieve substantially more bandwidth density and in peaks closer to the 10,000 Gbps/km2 … easily.
Pretty Awesome Wow!
The basic; a Terabit equals 1024 Gigabits (but I tend to ignore that last 24 … sorry I am not).
With a traffic density of ca. 10,000 Gbps per km2, one would expect to have between 1,000 (@ 10 Gbps peak) to 10,000 (@ 1 Gbps peak) concurrent users per square km.
At 10 Mbps/MHz/Cell one would expect to have a 1,000 Cell-GHz/km2. Assume that we would have 1 GHz bandwidth (i.e., somewhere in the 30 – 300 GHz mm-wave range), one would need 1,000 cells per km2. On average with a cell range of about 20 meters (smaller to smallest … I guess what Nokia would call an Hyper-Ultra-Dense Network;-). Thus each cell would minimum have between 1 to 10 concurrent users.
Just as a reminder! 1 minutes at 1 Gbps corresponds to 7.5 GB. A bit more than what you need for a 80 minute HD (i.e., 720pp) full movie stream … in 1 minutes. So with your (almost) personal smallest cell what about the remaining 59 minutes? Seems somewhat wasteful at least until kingdom come (alas maybe sooner than that).
It would appear that the very high 5G data density target could result in very in-efficient networks from a utilization perspective.
≥ 1 MN / Km2 DEVICE DENSITY.
One million 5G devices per square kilometer appears to be far far out in a future where one would expect us to be talking about 7G or even higher Gs.
1 Million devices seems like a lot and certainly per km2. It is 1 device per square meter on average. A 20 meter cell-range smallest cell would contain ca. 1,200 devices.
To give this number perspective lets compare it with one of my favorite South-East Asian cities. The city with one of the highest population densities around, Manila (Philippines). Manila has more than 40 thousand people per square km. Thus in Manila this would mean that we would have about 24 devices per person or 100+ per household per km2. Overall, in Manila we would then expect approx. 40 million devices spread across the city (i.e., Manila has ca. 1.8 Million inhabitants over an area of 43 km2. Philippines has a population of approx. 100 Million).
Just for the curious, it is possible to find other more populated areas in the world. However, these highly dense areas tends to be over relative smaller surface areas, often much smaller than a square kilometer and with relative few people. For example Fadiouth Island in Dakar have a surface area of 0.15 km2 and 9,000 inhabitants making it one of the most pop densest areas in the world (i.e., 60,000 pop per km2).
I hope I made my case! A million devices per km2 is a big number.
Let us look at it from a forecasting perspective. Just to see whether we are possibly getting close to this 5G ambition number.
IHS forecasts 30.5 Billion installed devices by 2020, IDC is also believes it to be around 30 Billion by 2020. Machina Research is less bullish and projects 27 Billion by 2025 (IHS expects that number to be 75.4 Billion) but this forecast is from 2013. Irrespective, we are obviously in the league of very big numbers. By the way 5G IoT if at all considered is only a tiny fraction of the overall projected IoT numbers (e.g., Machine Research expects 10 Million 5G IoT connections by 2024 …that is extremely small numbers in comparison to the overall IoT projections).
To break this number down to something that could be more meaningful than just being Big and impressive, let just establish a couple of worldish numbers that can help us with this;
2020 population expected to be around 7.8 Billion compared to 2016 7.4 Billion.
Global pop per HH is ~3.5 (average number!) which might be marginally lower in 2020. Urban populations tend to have less pop per households ca. 3.0. Urban populations in so-called developed countries are having a pop per HH of ca. 2.4.
ca. 55% of world population lives in Urban areas. This will be higher by 2020.
Less than 20% of world population lives in developed countries (based on HDI). This is a 2016 estimate and will be higher by 2020.
World surface area is 510 Million km2 (including water).
of which ca. 150 million km2 is land area
of which ca. 75 million km2 is habitable.
of which 3% is an upper limit estimate of earth surface area covered by urban development, i.e., 15.3 Million km2.
of which approx. 1.7 Million km2 comprises developed regions urban areas.
ca. 37% of all land-based area is agricultural land.
Using 30 Billion IoT devices by 2020 is equivalent to;
ca. 4 IoT per world population.
ca. 14 IoT per world households.
ca. 200 IoT per km2 of all land-based surface area.
ca. 2,000 IoT per km2 of all urban developed surface area.
If we limit IoT’s in 2020 to developed countries, which wrongly or rightly exclude China, India and larger parts of Latin America, we get the following by 2020;
ca. 20 IoT per developed country population.
ca. 50 IoT per developed country households.
ca. 18,000 IoT per km2 developed country urbanized areas.
Given that it would make sense to include larger areas and population of both China, India and Latin America, the above developed country numbers are bound to be (a lot) lower per Pop, HH and km2. If we include agricultural land the number of IoTs will go down per km2.
So far far away from a Million IoT per km2.
What about parking spaces, for sure IoT will add up when we consider parking spaces!? … Right? Well in Europe you will find that most big cities will have between 50 to 200 (public) parking spaces per square kilometer (e.g., ca. 67 per km2 for Berlin and 160 per km2 in Greater Copenhagen). Aha not really making up to the Million IoT per km2 … what about cars?
In EU28 there are approx. 256 Million passenger cars (2015 data) over a population of ca. 510 Million pops (or ca. 213 million households). So a bit more than 1 passenger car per household on EU28 average. In Eu28 approx. 75+% lives in urban area which comprises ca. 150 thousand square kilometers (i.e., 3.8% of EU28’s 4 Million km2). So one would expect little more (if not a little less) than 1,300 passenger cars per km2. You may say … aha but it is not fair … you don’t include motor vehicles that are used for work … well that is an exercise for you (too convince yourself why that doesn’t really matter too much and with my royal rounding up numbers maybe is already accounted for). Also consider that many EU28 major cities with good public transportation are having significantly less cars per household or population than the average would allude to.
Surely, public street light will make it through? Nope! Typical bigger modern developed country city will have on average approx. 85 street lights per km2, although it varies from 0 to 1,000+. Light bulbs per residential household (from a 2012 study of the US) ranges from 50 to 80+. In developed countries we have roughly 1,000 households per km2 and thus we would expect between 50 thousand to 80+ thousand lightbulbs per km2. Shops and business would add some additions to this number.
With a cumulated annual growth rate of ca. 22% it would take 20 years (from 2020) to reach a Million IoT devices per km2 if we will have 20 thousand per km2 by 2020. With a 30% CAGR it would still take 15 years (from 2020) to reach a Million IoT per km2.
The current IoT projections of 30 Billion IoT devices in operation by 2020 does not appear to be unrealistic when broken down on a household or population level in developed areas (even less ambitious on a worldwide level). The 18,000 IoT per km2 of developed urban surface area by 2020 does appear somewhat ambitious. However, if we would include agricultural land the number would become possible a more reasonable.
If you include street crossings, traffic radars, city-based video monitoring (e.g., London has approx. 300 per km2, Hong Kong ca. 200 per km2), city-based traffic sensors, environmental sensors, etc.. you are going to get to sizable numbers.
Maybe the 1 Million Devices per km2 ambition is not one of the most important 5G design criteria’s for the short term (i.e., next 10 – 20 years).
Oh and most IoT forecasts from the period 2015 – 2016 does not really include 5G IoT devices in particular. The chart below illustrates Machina Research IoT forecast for 2024 (from August 2015). In a more recent forecast from 2016, Machine Research predict that by 2024 there would be ca. 10 million 5G IoT connections or 0.04% of the total number of forecasted connections;
The winner is … IoTs using WiFi or other short range communications protocols. Obviously, the cynic in me (mea culpa) would say that a mm-wave based 5G connections can also be characterized as short range … so there might be a very interesting replacement market there for 5G IoT … maybe? 😉
Expectations to 5G-based IoT does not appear to be very impressive at least over the next 10 years and possible beyond.
The un-importance of 5G IoT should not be a great surprise given most 5G deployment scenarios are focused on millimeter-wave smallest 5G cell coverage which is not good for comprehensive coverage of IoT devices not being limited to those very special 5G coverage situations being thought about today.
Only operators focusing on comprehensive 5G coverage re-purposing lower carrier frequency bands (i.e., 1 GHz and lower) can possible expect to gain a reasonable (as opposed to niche) 5G IoT business. T-Mobile US with their 600 MHz 5G strategy might very well be uniquely positions for taking a large share of future proof IoT business across USA. Though they are also pretty uniquely position for NB-IoT with their comprehensive 700MHz LTE coverage.
For 5G IoT to be meaningful (at scale) the conventional macro-cellular networks needs to be in play for 5G coverage .,, certainly 100% 5G coverage will be a requirement. Although, even with 5G there maybe 100s of Billion of non-5G IoT devices that require coverage and management.
≤ 500 km/h SERVICE SUPPORT.
Sure why not? but why not faster than that? At hyperloop or commercial passenger airplane speeds for example?
Before we get all excited about Gbps speeds at 500 km/h, it should be clear that the 5G vision paper only proposed speeds between 10 Mbps up-to 50 Mbps (actually it is allowed to regress down to 50 kilo bits per second). With 200 Mbps for broadcast like services.
So in general, this is a pretty reasonable requirement. Maybe with the 200 Mbps for broadcasting services being somewhat head scratching unless the vehicle is one big 16K screen. Although the users proximity to such a screen does not guaranty an ideal 16K viewing experience to say the least.
What moves so fast?
The fastest train today is tracking at ca. 435 km/h (Shanghai Maglev, China).
Typical cruising airspeed for a long-distance commercial passenger aircraft is approx. 900 km/h. So we might not be able to provide the best 5G experience in commercial passenger aircrafts … unless we solve that with an in-plane communications system rather than trying to provide Gbps speed by external coverage means.
Why take a plane when you can jump on the local Hyperloop? The proposed Hyperloop should track at an average speed of around 970 km/h (faster or similar speeds as commercial passengers aircrafts), with a top speed of 1,200 km/h. So if you happen to be in between LA and San Francisco in 2020+ you might not be able to get the best 5G service possible … what a bummer! This is clearly an area where the vision did not look far enough.
Providing services to moving things at a relative fast speed does require a reasonable good coverage. Whether it being train track, hyperloop tunnel or ground to air coverage of commercial passenger aircraft, new coverage solutions would need to be deployed. Or alternative in-vehicular coverage solutions providing a perception of 5G experience might be an alternative that could turn out to be more economical.
The speed requirement is a very reasonable one particular for train coverage.
50% TOTAL NETWORK ENERGY REDUCTION.
If 5G development could come true on this ambition we talk about 10 Billion US Dollars (for the cellular industry). Equivalent to a percentage point on the margin.
There are two aspects of energy efficiency in a cellular based communication system.
User equipment that will benefit from longer intervals without charging and thus improve customers experience and overall save energy from less frequently charges.
Network infrastructure energy consumption savings will directly positively impact a telecom operators Ebitda.
Energy efficient Smartphones
The first aspect of user equipment is addressed by the 5G vision paper under “4.3 Device Requirements” sub-section “4.3.3 Device Power Efficiency”; “Battery life shall be significantly increased: at least 3 days for a smartphone, and up tp 15 years for a low-cost MTC device.”(note: MTC = Machine Type Communications).
Apple’s iPhone 7 battery life (on a full charge) is around 6 hours of constant use with 7 Plus beating that with ca. 3 hours (i.e., total 9 hours). So 3 days will go a long way.
It is however unclear whether the 3 extra days of a 5G smartphone battery life-time is supposed to be under active usage conditions or just in idle mode. Obviously in order to matter materially to the consumer one would expect this vision to apply to active usage (i.e., 4+ hours a day at 100s of Mbps – 1Gbps operations).
Energy efficient network infrastructure.
The 5G vision paper defines energy efficiency as number of bits that can be transmitted over the telecom infrastructure per Joule of Energy.
The total energy cost, i.e., operational expense (OpEx), of telecommunications network can be considerable. Despite our mobile access technologies having become more energy efficient with each generation, the total OpEx of energy attributed to the network infrastructure has increased over the last 10 years in general. The growth in telco infrastructure related energy consumption has been driven by the consumer demand for broadband services in mobile and fixed including incredible increase in data center computing and storage requirements.
In general power consumption OpEx share of total technology cost amounts to 8% to 15% (i.e., for Telcos without heavy reliance of diesel). The general assumption is that with regular modernization, energy efficiency gain in newer electronics can keep growth in energy consumption to a minimum compensating for increased broadband and computing demand.
Note: Technology Opex (including NT & IT) on average lays between 18% to 25% of total corporate Telco Opex. Out of the Technology Opex between 8% to 15% (max) can typically be attributed to telco infrastructure energy consumption. The access & aggregation contribution to the energy cost typically would towards 80% plus. Data centers are expected to increasingly contribute to the power consumption and cost as well. Deep diving into the access equipment power consumption, ca. 60% can be attributed to rectifiers and amplifiers, 15% by the DC power system & miscellaneous and another 25% by cooling.
5G vision paper is very bullish in their requirement to reduce the total energy and its associated cost; it is stated “5G should support a 1,000 times traffic increase in the next 10 years timeframe, with an energy consumption by the whole network of only half that typically consumed by today’s networks. This leads to the requirement of an energy efficiency of x2,000 in the next 10 years timeframe.” (sub-section “4.6.2 Energy Efficiency” NGMN 5G White Paper).
This requirement would mean that in a pure 5G world (i.e., all traffic on 5G), the power consumption arising from the cellular network would be 50% of what is consumed today. In 2016 terms the Mobile-based Opex saving would be in the order of 5 Billion US$ to 10+ Billion US$ annually. This would be equivalent to 0.5% to 1.1% margin improvement globally (note: using GSMA 2016 Revenue & Growth data and Pyramid Research forecast). If energy price would increase over the next 10 years the saving / benefits would of course be proportionally larger.
As we have seen in the above, it is reasonable to expect a very considerable increase in cell density as the broadband traffic demand increases from peak bandwidth (i.e., 1 – 10 Gbps) and traffic density (i.e., 1 Tbps per km2) expectations.
Depending on the demanded traffic density, spectrum and carrier frequency available for 5G between 100 to 1,000 small cell sites per km2 could be required over the next 10 years. This cell site increase will be required in addition to existing macro-cellular network infrastructure.
Today (in 2017) an operator in EU28-sized country may have between ca. 3,500 to 35,000 cell sites with approx. 50% covering rural areas. Many analysts are expecting that for medium sized countries (e.g., with 3,500 – 10,000 macro cellular sites), operators would eventually have up-to 100,000 small cells under management in addition to their existing macro-cellular sites. Most of those 5G small cells and many of the 5G macro-sites we will have over the next 10 years, are also going to have advanced massive MiMo antenna systems with many active antenna elements per installed base antenna requiring substantial computing to gain maximum performance.
It appears with today’s knowledge extremely challenging (to put it mildly) to envision a 5G network consuming 50% of today’s total energy consumption.
It is highly likely that the 5G radio node electronics in a small cell environment (and maybe also in a macro cellular environment?) will consume less Joules per delivery bit (per second) due to technology advances and less transmitted power required (i.e., its a small or smallest cell). However, this power efficiency technology and network cellular architecture gain can very easily be destroyed by the massive additional demand of small, smaller and smallest cells combined with highly sophisticated antenna systems consuming additional energy for their compute operations to make such systems work. Furthermore, we will see operators increasingly providing sophisticated data center resources network operations as well as for the customers they serve. If the speed of light is insufficient for some services or country geographies, additional edge data centers will be introduced, also leading to an increased energy consumption not present in todays telecom networks. Increased computing and storage demand will also make the absolute efficiency requirement highly challenging.
Will 5G be able to deliver bits (per second) more efficiently … Yes!
Will 5G be able to reduce the overall power consumption of todays telecom networks with 50% … highly unlikely.
In my opinion the industry will have done a pretty good technology job if we can keep the existing energy cost at the level of today (or even allowing for unit price increases over the next 10 years).
The Total power reduction of our telecommunications networks will be one of the most important 5G development tasks as the industry cannot afford a new technology that results in waste amount of incremental absolute cost. Great relative cost doesn’t matter if it results in above and beyond total cost.
≥ 99.999% NETWORK AVAILABILITY & DATA CONNECTION RELIABILITY.
A network availability of 5Ns across all individual network elements and over time correspond to less than a second a day downtime anywhere in the network. Few telecom networks are designed for that today.
5 Nines (5N) is a great aspiration for services and network infrastructures. It also tends to be fairly costly and likely to raise the level of network complexity. Although in the 5G world of heterogeneous networks … well its is already complicated.
5N Network Availability.
From a network and/or service availability perspective it means that over the cause of the day, your service should not experience more than 0.86 seconds of downtime. Across a year the total downtime should not be more than 5 minutes and 16 seconds.
The way 5N Network Availability is define is “The network is available for the targeted communications in 99.999% of the locations where the network is deployed and 99.999% of the time”. (from “4.4.4 Resilience and High Availability”, NGMN 5G White Paper).
Thus in a 100,000 cell network only 1 cell is allowed experience a downtime and for no longer than less than a second a day.
It should be noted that there are not many networks today that come even close to this kind of requirement. Certainly in countries with frequent long power outages and limited ancillary backup (i.e., battery and/or diesel) this could be a very costly design requirement. Networks relying on weather-sensitive microwave radios for backhaul or for mm-wave frequencies 5G coverage would be required to design in a very substantial amount of redundancy to keep such high geographical & time availability requirements
In general designing a cellular access network for this kind of 5N availability could be fairly to very costly (i.e., Capex could easily run up in several percentage points of Revenue).
One way out from a design perspective is to rely on hierarchical coverage. Thus, for example if a small cell environment is un-available (=down!) the macro-cellular network (or overlay network) continues the service although at a lower service level (i.e., lower or much lower speed compared to the primary service). As also suggested in the vision paper making use of self-healing network features and other real-time measures are expected to further increase the network infrastructure availability. This is also what one may define as Network Resilience.
Nevertheless, the “NGMN 5G White Paper” allows for operators to define the level of network availability appropriate from their own perspective (and budgets I assume).
5N Data Packet Transmission Reliability.
The 5G vision paper, defines Reliability as “… amount of sent data packets successfully delivered to a given destination, within the time constraint required by the targeted service, divided by the total number of sent data packets.”. (“4.4.5 Reliability” in “NGMN 5G White Paper”).
It should be noted that the 5N specification in particular addresses specific use cases or services of which such a reliability is required, e.g., mission critical communications and ultra-low latency service. The 5G allows for a very wide range of reliable data connection. Whether the 5N Reliability requirement will lead to substantial investments or can be managed within the overall 5G design and architectural framework, might depend on the amount of traffic requiring 5Ns.
The 5N data packet transmission reliability target would impose stricter network design. Whether this requirement would result in substantial incremental investment and cost is likely dependent on the current state of existing network infrastructure and its fundamental design.
If you have read Michael Lewis book “Flash Boys”, I will have absolutely no problem convincing you that a few milliseconds improvement in transport time (i.e., already below 20 ms) of a valuable signal (e.g., containing financial information) can be of tremendous value. It is all about optimizing transport distances, super efficient & extremely fast computing and of course ultra-high availability. The ultra-low transport and process latencies is the backbone (together with the algorithms obviously) of the high frequency trading industry that takes a market share of between 30% (EU) and 50% (US) of the total equity trading volume.
In a recent study by The Boston Consulting Group (BCG) “Uncovering Real Mobile Data Usage and Drivers of Customer Satisfaction” (Nov. 2015) study it was found that latency had a significant impact on customer video viewing satisfaction. For latencies between 75 – 100 milliseconds 72% of users reported being satisfied. The user experience satisfaction level jumped to 83% when latency was below 50 milliseconds. We have most likely all experienced and been aggravated by long call setup times (> couple of seconds) forcing us to look at the screen to confirm that a call setup (dialing) is actually in progress.
Latency and reactiveness or responsiveness matters tremendously to the customers experience and whether it is a bad, good or excellent one.
The Tactile Internet idea is an integral part of the “NGMN 5G Vision” and part of what is characterized as Extreme Real-Time Communications. It has further been worked out in detail in the ITU-T Technology Watch Report “The Tactile Internet” from August 2014.
The word “Tactile” means perceptible by touch. It closely relates to the ambition of creating a haptic experience. Where haptic means a sense of touch. Although we will learn that the Tactile Internet vision is more than a “touchy-feeling” network vision, the idea of haptic feedback in real-time (~ sub-millisecond to low millisecond regime) is very important to the idea of a Tactile Network experience (e.g., remote surgery).
The Tactile Internet is characterized by
Ultra-low latency; 1 ms and below latency (as in round-trip-time / round-trip delay).
Ultra-high availability; 99.999% availability.
Ultra-secure end-2-end communications.
Persistent very high bandwidths capability; 1 Gbps and above.
The Tactile Internet is one of the corner stones of 5G. It promises ultra-low end-2-end latencies in the order of 1 millisecond at Giga bits per second speeds and with five 9’s of availability (translating into a 500 ms per day average un-availability).
Interestingly, network predictability and variation in latency have not been receiving too much focus within the Tactile Internet work. Clearly, a high degree of predictability as well as low jitter (or latency variation), could be very desirable property of a tactile network. Possibly even more so than absolute latency in its own right. A right sized round-trip-time with imposed managed latency, meaning a controlled variation of latency, is very essential to the 5G Tactile Internet experience.
It’s 5G on speed and steroids at the same time.
Let us talk about the elephant in the room.
We can understand Tactile latency requirements in the following way;
An Action including (possible) local Processing, followed by some Transport and Remote Processing of data representing the Action, results in a Re-action again including (possible) local Processing. According with Tactile Internet Vision, the time of this whole even from Action to Re-action has to have run its cause within 1 millisecond or one thousand of a second. In many use cases this process is looped as the Re-action feeds back, resulting in another action. Note in the illustration below, Action and Re-action could take place on the same device (or locality) or could be physically separated. The processes might represent cloud-based computations or manipulations of data or data manipulations local to the device of the user as well as remote devices. It needs to be considered that the latency time scale for one direction is not at all given to be the same in the other direction (even for transport).
The simplest example is the mouse click on a internet link or URL (i.e., the Action) resulting a translation of the URL to an IP address and the loading of the resulting content on your screen (i.e., part of the process) with the final page presented on the your device display (i.e., Re-action). From the moment the URL is mouse-clicked until the content is fully presented should take no longer than 1 ms.
A more complex use case might be remote surgery. In which a surgical robot is in one location and the surgeon operator is at another location manipulating the robot through an operation. This is illustrated in the above picture. Clearly, for a remote surgical procedure to be safe (i.e., within the margins of risk of not having the possibility of any medical assisted surgery) we would require a very reliable connection (99.999% availability), sufficient bandwidth to ensure adequate video resolution as required by the remote surgeon controlling the robot, as little as possible latency allowing the feel of instantaneous (or predictable) reaction to the actions of the controller (i.e., the surgeons) and of course as little variation in the latency (i.e., jitter) allowing system or human correction of the latency (i.e., high degree of network predictability).
The first Complete Trans-Atlantic Robotic Surgery happened in 2001. Surgeons in New York (USA) remotely operated on a patient in Strasbourg, France. Some 7,000 km away or equivalent to 70 ms in round-trip-time (i.e., 14,000 km in total) for light in fiber. The total procedural delay from hand motion (action) to remote surgical response (reaction) showed up on their video screen took 155 milliseconds. From trials on pigs any delay longer than 330 ms was thought to be associated with an unacceptable degree of risk for the patient. This system then did not offer any haptic feedback to the remote surgeon. This remains the case for most (if not all) remote robotic surgical systems in option today as the latency in most remote surgical scenarios render haptic feedback less than useful. An excellent account for robotic surgery systems (including the economics) can be found at this web site “All About Robotic Surgery”. According to experienced surgeons at 175 ms (and below) a remote robotic operation is perceived (by the surgeon) as imperceptible.
It should be clear that apart from offering long-distance surgical possibilities, robotic surgical systems offers many other benefits (less invasive, higher precision, faster patient recovery, lower overall operational risks, …). In fact most robotic surgeries are done with surgeon and robot being in close proximity.
Another example of coping with lag or latency is a Predator drone pilot. The plane is a so-called unmanned combat aerial vehicle and comes at a price of ca. 4 Million US$ (in 2010) per piece. Although this aerial platform can perform missions autonomously it will typically have two pilots on the ground monitoring and possible controlling it. The typical operational latency for the Predator can be as much as 2,000 milliseconds. For takeoff and landing, where this latency is most critical, typically the control is handed to to a local crew (either in Nevada or in the country of its mission). The Predator cruise speed is between 130 and 165 km per hour. Thus within the 2 seconds lag the plane will have move approximately 100 meters (i.e., obviously critical in landing & take off scenarios). Nevertheless, a very high degree of autonomy has been build into the Predator platform that also compensates for the very large latency between plane and mission control.
Back to the Tactile Internet latency requirements;
In LTE today, the minimum latency (internal to the network) is around 12 ms without re-transmission and with pre-allocated resources. However, the normal experienced latency (again internal to the network) would be more in the order of 20 ms including 10% likelihood of retransmission and assuming scheduling (which would be normal). However, this excludes any content fetching, processing, presentation on the end-user device and the transport path beyond the operators network (i.e., somewhere in the www). Transmission outside the operator network typically between 10 and 20 ms on-top of the internal latency. The fetching, processing and presentation of content can easily add hundreds of milliseconds to the experience. Below illustrations provides a high level view of the various latency components to be considered in LTE with the transport related latencies providing the floor level to be expected;
In 5G the vision is to achieve a factor 20 better end-2-end (within the operators own network) round-trip-time compared to LTE; thus 1 millisecond.
So … what happens in 1 millisecond?
Light will have travelled ca. 200 km in fiber or 300 km in free-space. A car driving (or the fastest baseball flying) 160 km per hour will have moved 4 cm. A steel ball falling to the ground (on Earth) would have moved 5 micro meter (that’s 5 millionth of a meter). In a 1Gbps data stream, 1 ms correspond to ca. 125 Kilo Bytes worth of data. A human nerve impulse last just 1 ms (i.e., in a 100 millivolt pulse).
It should be clear that the 1 ms poses some very dramatic limitations;
The useful distance over which a tactile applications would work (if 1 ms would really be the requirements that is!) will be short ( likely a lot less than 100 km for fiber-based transport)
The air-interface (& number of control plane messages required) needs to reduce dramatically from milliseconds down to microseconds, i.e., factor 20 would require no more than 100 microseconds limiting the useful cell range).
Compute & processing requirements, in terms of latency, for UE (incl. screen, drivers, local modem, …), Base Station and Core would require a substantial overhaul (likely limiting level of tactile sophistication).
Require own controlled network infrastructure (at least a lot easier to manage latency within), avoiding any communication path leaving own network (walled garden is back with a vengeance?).
Network is the sole responsible for latency and can be made arbitrarily small (by distance and access).
Very small cells, very close to compute & processing resources, would be most likely candidates for fulfilling the tactile internet requirements.
Thus instead of moving functionality and compute up and towards the cloud data center we (might) have an opposing force that requires close proximity to the end-users application. Thus, the great promise of cloud-based economical efficiency is likely going to be dented in this scenario by requiring many more smaller data centers and maybe even micro-data centers moving closer to the access edge (i.e., cell site, aggregation site, …). Not surprisingly, Edge Cloud, Edge Data Center, Edge X is really the new Black …The curse of the edge!?
Looking at several network and compute design considerations a tactile application would require no more than 50 km (i.e., 100 km round-trip) effective round-trip distance or 0.5 ms fiber transport (including switching & routing) round-trip-time. Leaving another 0.5 ms for air-interface (in a cellular/wireless scenario), computing & processing. Furthermore, the very high degree of imposed availability (i.e., 99.999%) might likewise favor proximity between the Tactile Application and any remote Processing-Computing. Obviously,
So in all likelihood we need processing-computing as near as possible to the tactile application (at least if one believes in the 1 ms and about target).
One of the most epic (“in the Dutch coffee shop after a couple of hours category”) promises in “The Tactile Internet” vision paper is the following;
“Tomorrow, using advanced tele-diagnostic tools, it could be available anywhere, anytime; allowing remote physical examination even by palpation (examination by touch). The physician will be able to command the motion of a tele-robot at the patient’s location and receive not only audio-visual information but also critical haptic feedback.” (page 6, section 3.5).
Markus Rank et al did systematic research on the perception of delay in haptic tele-presence systems (Presence, October 2010, MIT Press) and found haptic delay detection thresholds between 30 and 55 ms. Thus haptic feedback did not appear to be sensitive to delays below 30 ms, fairly close to the lowest reported threshold of 20 ms. This combined with experienced tele-robotic surgeons assessing that below 175 ms the remote procedure starts to be perceived as imperceptible, might indicate that the 1 ms, at least for this particular use case, is extremely limiting.
The extreme case would be to have the tactile-related computing done at the radio base station assuming that the tactile use case could be restricted to the covered cell and users supported by that cell. I name this the micro-DC (or micro-cloud or more like what some might call the cloudlet concept) idea. This would be totally back to the older days with lots of compute done at the cell site (and likely kill any traditional legacy cloud-based efficiency thinking … love to use legacy and cloud in same sentence). This would limit the round-trip-time to air-interface latency and compute/processing at the base station and the device supporting the tactile application.
It is normal to talk about the round-trip-time between an action and the subsequent reaction. It is also the time it takes a data or signal to travel from a specific source to a specific destination and back again (i.e., round trip). In case of light in fiber, a 1 millisecond limit on the round-trip-time would imply that the maximum distance that can be travelled (in the fiber) between source to destination and back to the source is 200 km. Limiting the destination to be no more than 100 km away from the source. In case of substantial processing overhead (e.g., computation) the distance between source and destination requires even less than 100 km to allow for the 1 ms target.
THE HUMAN SENSES AND THE TACTILE INTERNET.
The “touchy-feely” aspect, or human sensing in general, is clearly an inspiration to the authors of “The Tactile Internet” vision as can be seen from the following quote;
“We experience interaction with a technical system as intuitive and natural only if the feedback of the system is adapted to our human reaction time. Consequently, the requirements for technical systems enabling real-time interactions depend on the participating human senses.” (page 2, Section 1).
The following human-reaction times illustration shown below is included in “The Tactile Internet” vision paper. Although it originates from Fettweis and Alamouti’s paper titled “5G: Personal Mobile Internet beyond What Cellular Did to Telephony“. It should be noted that the description of the Table is order of magnitude of human reaction times; thus, 10 ms might also be 100 ms or 1 ms and so forth and therefor, as we shall see, it would be difficult to a given reaction time wrong within such a range.
The important point here is that the human perception or senses impact very significantly the user’s experience with a given application or use case.
The responsiveness of a given system or design is incredible important for how well a service or product will be perceived by the user. The responsiveness can be defined as a relative measure against our own sense or perception of time. The measure of responsiveness is clearly not unique but depends on what senses are being used as well as the user engaged.The human mind is not fond of waiting and waiting too long causes distraction, irritation and ultimate anger after which the customer is in all likelihood lost. A very good account of considering the human mind and it senses in design specifications (and of course development) can be found in Jeff Johnson’s 2010 book “Designing with the Mind in Mind”.
The understanding of human senses and the neurophysiological reactions to those senses are important for assessing a given design criteria’s impact on the user experience. For example, designing for 1 ms or lower system reaction times when the relevant neurophysiological timescale is measured in 10s or 100s of milliseconds is likely not resulting in any noticeable (and monetizable) improvement in customer experience. Of course there can be many very good non-human reasons for wanting low or very low latencies.
While you might get the impression, from the above table above from Fettweis et al and countless Tactile Internet and 5G publications referring back to this data, that those neurophysiological reactions are natural constants, it is unfortunately not the case. Modality matters hugely. There are fairly great variations in reactions time within the same neurophysiological response category depending on the individual human under test but often also depending on the underlying experimental setup. In some instances the reaction time deduced would be fairly useless as a design criteria for anything as the detection happens unconsciously and still require the relevant part of the brain to make sense of the event.
Based on IAAF (International Athletic Association Federation) rules, an athlete is deemed to have had a false start if that athlete moves sooner than 100 milliseconds after the start signal. The neurophysiological process relevant here is the neuromuscular reaction to the sound heard (i.e., the big bang of the pistol) by the athlete. Research carried out by Paavo V. Komi et al has shown that the reaction time of a prepared (i.e., waiting for the bang!) athlete can be as low as 80 ms. This particular use case relates to the auditory reaction times and the subsequent physiological reaction. P.V. Komi et al also found a great variation in the neuromuscular reaction time to the sound (even far below the 80 ms!).
Neuromuscular reactions to unprepared events typically typically measures in several hundreds of milliseconds (up-to 700 ms) being somewhat faster if driven by auditory senses rather than vision. Note that reflex time scales are approximately 10 times faster or in the order of 80 – 100 ms.
The international Telecommunications Union (ITU) Recommendation G.114, defines for voice applications an upper acceptable one-way (i.e., its you talking you don’t want to be talked back to by yourself) delay of 150 ms. Delays below this limit would provide an acceptable degree of voice user experience in the sense that most users would not hear the delay. It should be understood that a great variation in voice delay sensitivity exist across humans. Voice conversations would be perceived as instantaneous by most below the 100 ms (thought the auditory perception would also depend on the intensity/volume of the voice being listened to).
Finally, let’s discuss human vision. Fettweis et al in my opinion mixes up several psychophysical concepts of vision and TV specifications. Alluding to 10 millisecond is the visual “reaction” time (whatever that now really means). More accurately they describe the phenomena of flicker fusion threshold which describes intermittent light stimulus (or flicker) is perceived as completely steady to an average viewer. This phenomena relates to persistence of vision where the visual system perceives multiple discrete images as a single image (both flicker and persistence of vision are well described in both by Wikipedia and in detail by Yhong-Lin Lu el al “Visual Psychophysics”). There, are other reasons why defining flicker fusion and persistence of vision as a human reaction reaction mechanism is unfortunate.
The 10 ms for vision reaction time, shown in the table above, is at the lowest limit of what researchers (see references 14, 15, 16 ..) find to be the early stages of vision can possible detect (i.e., as opposed to pure guessing ). Mary C. Potter of M.I.T.’s Dept. of Brain & Cognitive Sciences, seminal work on human perception in general and visual perception in particular shows that the human vision is capable very rapidly to make sense of pictures, and objects therein, on the timescale of 10 milliseconds (i.e., 13 ms actually is the lowest reported by Potter). From these studies it is also found that preparedness (i.e., knowing what to look for) helps the detection process although the overall detection results did not differ substantially from knowing the object of interest after the pictures were shown. Note that the setting of these visual reaction time experiments all happens in a controlled laboratory setting with the subject primed to being attentive (e.g., focus on screen with fixation cross for a given period, followed by blank screen for another shorter period, and then a sequence of pictures each presented for a (very) short time, followed again by a blank screen and finally a object name and the yes-no question whether the object was observed in the sequence of pictures). Often these experiments also includes a certain degree of training before the actual experiment took place. The relevant memory of the target object, In any case and unless re-enforced, will rapidly dissipates. in fact the shorter the viewing time, the quicker it will disappear … which might be a very healthy coping mechanism.
To call this visual reaction time of 10+ ms typical is in my opinion a bit of a stretch. It is typical for that particular experimental setup and very nicely provides important insights into the visual systems capabilities.
One of the more silly things used to demonstrate the importance of ultra-low latencies have been to time delay the video signal send to a wearer’s goggles and then throw a ball at him in the physical world … obviously, the subject will not catch the ball (might as well as thrown it at the back of his head instead). In the Tactile Internet vision paper it the following is stated; “But if a human is expecting speed, such as when manually controlling a visual scene and issuing commands that anticipate rapid response, 1-millisecond reaction time is required” (on page 3). And for the record spinning a basketball on your finger has more to do with physics than neurophysiology and human reaction times.
In more realistic settings it would appear that the (prepared) average reaction time of vision is around or below 40 ms. With this in mind, a baseball moving (when thrown by a power pitcher) at 160 km per hour (or ca. 4+ cm per ms) would take a approx. 415 ms to reach the batter (using an effective distance of 18.44 meters). Thus the batter has around 415 ms to visually process the ball coming and hit it at the right time. Given the latency involved in processing vision the ball would be at least 40 cm (@ 10 ms) closer to the batter than his latent visionary impression would imply. Assuming that the neuromuscular reaction time is around 100±20 ms, the batter would need to compensate not only for that but also for his vision process time in order to hit the ball. Based on batting statistics, clearly the brain does compensate for its internal latencies pretty well. In the paper “Human time perception and its illusions” D.M. Eaglerman that the visual system and the brain (note: visual system is an integral part of the brain) is highly adaptable in recalibrating its time perception below the sub-second level.
It is important to realize that in literature on human reaction times, there is a very wide range of numbers for supposedly similar reaction use cases and certainly a great deal of apparent contradictions (though the experimental frameworks often easily accounts for this).
The supporting data for the numbers shown in the above figure can be found via the hyperlink in the above text or in the references below.
Thus, in my opinion, also supported largely by empirical data, a good latency E2E design target for a Tactile network serving human needs, would be between 20 milliseconds and 10 milliseconds. With the latency budget covering the end user device (e.g., tablet, VR/AR goggles, IOT, …), air-interface, transport and processing (i.e., any computing, retrieval/storage, protocol handling, …). It would be unlikely to cover any connectivity out of the operator”s network unless such a connection is manageable from latency and jitter perspective though distance would count against such a strategy.
This would actually be quiet agreeable from a network perspective as the distance to data centers would be far more reasonable and likely reduce the aggressive need for many edge data centers using the below 10 ms target promoted in the Tactile Internet vision paper.
There is however one thing that we are assuming in all the above. It is assumed that the user’s local latency can be managed as well and made almost arbitrarily small (i.e., much below 1 ms). Hardly very reasonable even in the short run for human-relevant communications ecosystems (displays, goggles, drivers, etc..) as we shall see below.
For a gaming environment we would look at something like the below illustration;
Lets ignore the use case of local games (i.e., where the player only relies on his local computing environment) and focus on games that rely on a remote gaming architecture. This could either be relying on a client-server based architecture or cloud gaming architecture (e.g., typical SaaS setup). In general the the client-server based setup requires more performance of the users local environment (e.g., equipment) but also allows for more advanced latency compensating strategies enhancing the user perception of instantaneous game reactions. In the cloud game architecture, all game related computing including rendering/encoding (i.e., image synthesis) and video output generation happens in the cloud. The requirements to the end users infrastructure is modest in the cloud gaming setup. However, applying latency reduction strategies becomes much more challenging as such would require much more of the local computing environment that the cloud game architecture tries to get away from. In general the network transport related latency would be the same provide the dedicated game servers and the cloud gaming infrastructure would reside within the same premises. In Choy et al’s 2012 paper “The Brewing Storm in Cloud Gaming: A Measurement Study on Cloud to End-User Latency” , it is shown, through large scale measurements, that current commercial cloud infrastructure architecture is unable to deliver the latency performance for an acceptable (massive) multi-user experience. Partly simply due to such cloud data centers are too far away from the end user. Moreover, the traditional commercial cloud computing infrastructure is simply not optimized for online gaming requiring augmentation of stronger computing resources including GPUs and fast memory designs. Choy et al do propose to distribute the current cloud infrastructure targeting a shorter distance between end user and the relevant cloud game infrastructure. Similar to what is already happening today with content distribution networks (CDNs) being distributed more aggressively in metropolitan areas and thus closer to the end user.
A comprehensive treatment on latencies, or response time scales, in games and how these relates to user experience can be found in Kjetil Raaen’s Ph.D. thesis “Response time in games: Requirements and improvements” as well as in the comprehensive relevant literature list found in this thesis.
From the many studies (as found in Raaen’s work, the work of Mark Claypool and much cited 2002 study by Pantel et al) on gaming experience, including massive multi-user online game experience, shows that players starts to notice delay of about 100 ms of which ca. 20 ms comes from play-out and processing delay. Thus, quiet a far cry from the 1 millisecond. From the work, and not that surprising, sensitivity to gaming latency depends on the type of game played (see the work of Claypool) and how experienced a gamer is with the particular game (e.g., Pantel er al). It should also be noted that in a VR environment, you would want to the image that arrives at your visual system to be in synch with your heads movement and the directions of your vision. If there is a timing difference (or lag) between the direction of your vision and the image presented to your visual system, the user experience becomes rapidly poor causing discomfort by disorientation and confusion (possible leading to a physical reaction such as throwing up). It is also worth noting that in VR there is a substantially latency component simple from the image rendering (e.g., 60 MHz frame rate provides a new frame on average every 16.7 millisecond). Obviously chunking up the display frame rate will reduce the rendering related latency. However, several latency compensation strategies (to compensate for you head and eye movements) have been developed to cope with VR latency (e.g., time warping and prediction schemes).
Anyway, if you would be of the impression that VR is just about showing moving images on the inside of some awesome goggles … hmmm do think again and keep dreaming of 1 millisecond end-2end network centric VR delivery solutions (at least for the networks we have today). Of course 1 ms target is possible really a Proxima-Centauri shot as opposed to a just moonshot.
With a target of no more than 20 milliseconds lag or latency and taking into account the likely reaction time of the users VR system (future system!), that likely leaves no more (and likely less) than 10 milliseconds for transport and any remote server processing. Still this could allow for a data center to be 500 km (5 ms round.trip time in fiber) away from the user and allow another 5 ms for data center processing and possible routing delay along the way.
One might very well be concerned about the present Tactile Internet vision and it’s focus on network centric solutions to the very low latency target of 1 millisecond. The current vision and approach would force (fixed and mobile) network operators to add a considerable amount of data centers in order to get the physical transport time down below the 1 millisecond. This in turn drives the latest trend in telecommunication, the so-called edge data center or edge cloud. In the ultimate limit, such edge data centers (however small) might be placed at cell site locations or fixed network local exchanges or distribution cabinets.
Furthermore, the 1 millisecond as a goal might very well have very little return on user experience (UX) and substantial cost impact for telecom operators. A diligent research through academic literature and wealth of practical UX experiments indicates that this indeed might be the case.
Such a severe and restrictive target as the 1 millisecond is, it severely narrows the Tactile Internet to scenarios where sensing, acting, communication and processing happens in very close proximity of each other. In addition the restrictions to system design it imposes, further limits its relevance in my opinion. The danger is, with the expressed Tactile vision, that too little academic and industrious thinking goes into latency compensating strategies using the latest advances in machine learning, virtual reality development and computational neuroscience (to name a few areas of obvious relevance). Further network reliability and managed latency, in the sense of controlling the variation of the latency, might be of far bigger importance than latency itself below a certain limit.
So if 1 ms is no use to most men and beasts … why bother with this?
While very low latency system architectures might be of little relevance to human senses, it is of course very likely (as it is also pointed out in the Tactile Internet Vision paper) that industrial use cases could benefit from such specifications of latency, reliability and security.
For example in machine-to-machine or things-to-things communications between sensors, actuators, databases, and applications very short reaction times in the order of sub-milliseconds to low milliseconds could be relevant.
We will look at this next.
THE TACTILE INTERNET USE CASES & BUSINESS MODELS.
An open mind would hope that most of what we do strives to out perform human senses, improve how we deal with our environment and situations that are far beyond mere mortal capabilities. Alas I might have read too many Isaac Asimov novels as a kid and young adult.
In particular where 5G has its present emphasis of ultra-high frequencies (i.e., ultra small cells), ultra-wide spectral bandwidth (i.e., lots of Gbps) together with the current vision of the Tactile Internet (ultra-low latencies, ultra-high reliability and ultra-high security), seem to be screaming for being applied to Industrial facilities, logistic warehouses, campus solutions, stadiums, shopping malls, tele-, edge-cloud, networked robotics, etc… In other words, wherever we have a happy mix of sensors, actuators, processors, storage, databases and software based solutions across a relative confined area, 5G and the Tactile Internet vision appears to be a possible fit and opportunity.
In the following it is important to remember;
1 ms round-trip time ~ 100 km (in fiber) to 150 km (in free space) in 1-way distance from the relevant action if only transport distance mattered to the latency budget.
Considering the total latency budget for a 1 ms Tactile application the transport distance is likely to be no more than 20 – 50 km or less (i.e., right at the RAN edge).
5G will bring lower latency, compared to an even optimized LTE system, that in a similar setup as the above described for Ocado, could further increase the performance. Obviously very high network reliability promised by 5G of such a logistic system needs to be very high to reduce the risk of disruption and subsequent customer dissatisfaction of late (or no) delivery as well as the exposure to grocery stock turning bad.
This all done within the confines of a warehouse building.
ROBOTICS AND TACTILE CONDITIONS
First of all lets limit the Robotics discussion to use cases related to networked robots. After all if the robot doesn’t need a network (pretty cool) it pretty much a singleton and not so relevant for the Tactile Internet discussion. In the following I am using the word Cloud in a fairly loose way and means any form of computing center resources either dedicated or virtualized. The cloud could reside near the networked robotic systems as well as far away depending on the overall system requirements to timing and delay (e.g., that might also depend on the level of robotic autonomy).
Getting networked robots to work well we need to solve a host of technical challenges, such as
Jitter (i.e., variation of latency).
Robot-2-ROS (i.e., general robotics operations system).
Power budget (e.g., power limitations, re-charging).
Sensor & actuator fusion (e.g., consolidate & align data from distributed sources for example sensor-actuator network).
Autonomy vs human control.
Machine learning / machine intelligence.
Safety (e.g., human and non-human).
Security (e.g., against cyber threats).
The network connection-part of the networked robotics system can be either wireless, wired, or a combination of wired & wireless. Connectivity could be either to a local computing cloud or data center, to an external cloud (on the internet) or a combination of internal computing for control and management for applications requiring very low-latency very-low jitter communications and external cloud for backup and latency-jitter uncritical applications and use cases.
For connection types we have Wired (e.g., LAN), Wireless (e.g., WLAN) and Cellular (e.g., LTE, 5G). There are (at least) three levels of connectivity we need to consider; inter-robot communications, robot-to-cloud communications (or operations and control systems residing in Frontend-Cloud or computing center), and possible Frontend-Cloud to Backend-Cloud (e..g, for backup, storage and latency-insensitive operations and control systems). Obviously, there might not be a need for a split in Frontend and Backend Clouds and pending on the use case requirements could be one and the same. Robots can be either stationary or mobile with a need for inter-robot communications or simply robot-cloud communications.
Various networked robot connectivity architectures are illustrated below;
I greatly acknowledge my wife Eva Varadi for her support, patience and understanding during the creative process of creating this Blog.
“Neurophysiology: A Conceptual Approach” by Roger Carpenter & Benjamin Reddi (Fifth Edition, 2013 CRC Press).Definitely a very worthy read by anyone who want to understand the underlying principles of sensory functions and basic neural mechanisms.
“Designing with the Mind in Mind” by Jeff Johnson (2010, Morgan Kaufmann). Lots of cool information of how to design a meaningful user interface and of basic user expirence principles worth thinking about.
“World first in radio design” by Cambridge Consultants. Describing the work Cambridge Consultants did with Ocado (UK-based) to design the worlds most automated technologically advanced warehouse based on 4G connected robotics. Please do see the video enclosed in page.
“Ocado: next-generation warehouse automation” by Cambridge Consultants.
After 3G came 4G. After 4G comes 5G. After 5G comes 6G. The Shrivatsa of Technology.
This blog (over the next months a series of Blogs dedicated to 5G), “5G Economics – An Introduction”, has been a very long undertaking. In the making since 2014. Adding and then deleting as I change my opinion and then changed it again. The NGNM Alliance “NGMN 5G White Paper” (here after the NGMN whitepaper) by Rachid El Hattachi & Javan Erfanian has been both a source of great visionary inspiration as well as a source of great worry when it comes to the economical viability of their vision. Some of the 5G ideas and aspirations are truly moonshot in nature and would make the Singularity University very proud.
So what is the 5G Vision?
“5G is an end-to-end ecosystem to enable a fully mobile and connected society. It empowers value creation towards customers and partners, through existing and emerging use cases, delivered with consistent experience, and enabled by sustainable business models.” (NGMN 5G Vision, NGMN 5G whitepaper).
The NGMN 5G vision is not only limited to enhancement of the radio/air interface (although it is the biggest cost & customer experience factor). 5G seeks to capture the complete end-2-end telecommunications system architecture and its performance specifications. This is an important difference from past focus on primarily air interface improvements (e.g., 3G, HSPA, LTE, LTE-adv) and relative modest evolutionary changes to the core network architectural improvements (PS CN, EPC). In particular, the 5G vision provides architectural guidance on the structural separation of hardware and software. Furthermore, it utilizes the latest development in software defined telecommunications functionality enabled by cloudification and virtualization concepts known from modern state-of-the art data centers. The NGMN 5G vision most likely have accepted more innovation risk than in the past as well as being substantially more ambitious in both its specifications and the associated benefits.
“To boldly go where no man has gone before”
In the following, I encourage the reader to always keep in the back of your mind; “It is far easier to criticize somebody’s vision, than it is to come with the vision yourself”. I have tons of respect for the hard and intense development work, that so far have been channeled into making the original 5G vision into a deployable technology that will contribute meaningfully to customer experience and the telecommunications industry.
For much of the expressed concerns in this blog and in other critiques, it is not that those concerns have not been considered in the NGMN whitepaper and 5G vision, but more that those points are not getting much attention.
The cellular “singularity”, 5G that is, is supposed to hit us by 2020. In only four years. Americans and maybe others, taking names & definitions fairly lightly, might already have “5G” ( a l’Americaine) in a couple of years before the real thing will be around.
The 5G Vision is a source of great inspiration. The 5G vision will (and is) requiring a lot of innovation efforts, research & development to actually deliver on what for most parts are very challenging improvements over LTE.
My own main points of concern are in particular towards the following areas;
Obsession with very high sustainable connection throughputs (> 1 Gbps).
Extremely low latencies (1 ms and below).
Too little (to none) focus on controlling latency variation (e.g., jitter), which might be of even greater importance than very low latency (<<10 ms) in its own right. I term this network predictability.
Too strong focus on frequencies above 3 GHz in general and in particular the millimeter wave range of 30 GHz to 300 GHz.
Backhaul & backbone transport transformation needed to support the 5G quantum leap in performance has been largely ignored.
Relative weak on fixed – mobile convergence.
Not so much whether some of the above points are important or not .. they are of course important. Rather it is a question of whether the prioritization and focus is right. A question of channeling more efforts into very important (IMO) key 5G success factors, e.g., transport, convergence and designing 5G for the best user experience (and infinitely faster throughput per user is not the answer) ensuring the technology to be relevant for all customers and not only the ones who happens to be within coverage of a smallest cell.
Not surprisingly the 5G vision is a very mobile system centric. There is too little attention to fixed-mobile convergence and the transport solutions (backhaul & backbone) that will enable the very high air-interface throughputs to be carried through the telecoms network. This is also not very surprising as most mobile folks, historically did not have to worry too much about transport at least in mature advanced markets (i.e., the solutions needed was there without innovation an R&D efforts).
However, this is a problem. The required transport upgrade to support the 5G promises is likely to be very costly. The technology economics and affordability aspects of what is proposed is still very much work in progress. It is speculated that new business models and use cases will be enabled by 5G. So far little has been done in quantifying those opportunities and see whether those can justify some of the incremental cost that surely operators will incur as the deploy 5G.
CELLULAR CAPACITY … IT WORKS FOR 5G TOO!
To create more cellular capacity measured in throughput is easy or can be made so with a bit of approximations. “All” we need is an amount of frequency bandwidth Hz, an air-interface technology that allow us to efficiently carry a certain amount of information in bits per second per unit bandwidth per capacity unit (i.e., we call this spectral efficiency) and a number of capacity units or multipliers which for a cellular network is the radio cell. The most challenging parameter in this game is the spectral efficiency as it is governed by the laws of physics with a hard limit (actually silly me … bandwidth and capacity units are obviously as well), while a much greater degree of freedom governs the amount of bandwidth and of course the number of cells.
Spectral efficiency is given by the so-called Shannon’s Law (for the studious inclined I recommend to study his 1948 paper “A Mathematical Theory of Communications”). The consensus is that we are very close to the Shannon Limit in terms of spectral efficiency (in terms of bits per second per Hz) of the cellular air-interface itself. Thus we are dealing with diminishing returns of what can be gained by further improving error correction, coding and single-input single-output (SISO) antenna technology.
I could throw more bandwidth at the capacity problem (i.e., the reason for the infatuation with the millimeter wave frequency range as there really is a lot available up there at 30+ GHz) and of course build a lot more cell sites or capacity multipliers (i.e., definitely not very economical unless it results in a net positive margin). Of course I could (and most likely will if I had a lot of money) do both.
I could also try to be smart about the spectral efficiency and Shannon’s law. If I could reduce the need for or even avoid building more capacity multipliers or cell sites, by increasing my antenna system complexity it is likely resulting in very favorable economics. It turns out that multiple antennas acts as a multiplier (simplistic put) for the spectral efficiency compared to a simple single (or legacy) antenna system. Thus, the way to improve the spectral efficiency inevitable leads us to substantially more complex antenna technologies (e.g., higher order MiMo, massive MiMo, etc…).
Building new cell sites or capacity multiplier should always be the last resort as it is most likely the least economical option available to boost capacity.
Thus we should be committing increasingly more bandwidth (i.e., 100s – 1000s of Mhz and beyond) assuming it is available (i.e, if not we are back to adding antenna complexity and more cell sites). The need for very large bandwidths, in comparison with what is deployed in today’s cellular systems, automatically forces the choices into high frequency ranges, i.e., >3 GHz and into the millimeter wave range of above 30 GHz. The higher frequency band leads in inevitably to limited coverage and a high to massive demand for small cell deployment.
Yes! It’s a catch 22 if there ever was one. The higher carrier frequency increases the likelihood of more available bandwidth. higher carrier frequency also results in a reduced the size of our advanced complex antenna system (which is good). Both boost capacity to no end. However, my coverage area where I have engineered the capacity boost reduces approx. with the square of the carrier frequency.
Clearly, ubiquitous 5G coverage at those high frequencies (i.e., >3 GHz) would be a very silly endeavor (to put it nicely) and very un-economical.
5G, as long as the main frequency deployed is in the high or very high frequency regime, would remain a niche technology. Irrelevant to a large proportion of customers and use cases.
5G needs to be macro cellular focused to become relevant for all customers and economically beneficial to most use cases.
THE CURIOUS CASE OF LATENCY.
The first time I heard about the 5G 1 ms latency target (communicated with a straight face and lots of passion) was to ROFL. Not a really mature reaction (mea culpa) and agreed, many might have had the same reaction when J.F. Kennedy announced to put a man on the moon and safely back on Earth within 10 years. So my apologies for having had a good laugh (likely not the last to laugh though in this matter).
In Europe, the average LTE latency is around 41±9 milliseconds including pinging an external (to the network) server but does not for example include the additional time it takes to load a web page or start a video stream. The (super) low latency (1 ms and below) poses other challenges but at least relevant to the air-interface and a reasonable justification to work on a new air-interface (apart from studying channel models in the higher frequency regime). The best latency, internal to the mobile network itself, you can hope to get out of “normal” LTE as it is commercially deployed is slightly below 20 ms (without considering re-transmission). For pre-allocated LTE this can further be reduced towards the 10 ms (without considering re-transmission which adds at least 8 ms). In 1 ms light travels ca. 200 km (in optical fiber). To support use cases requiring 1 ms End-2-End latency, all transport & processing would have to be kept inside the operators network. Clearly, the physical transport path to the location, where processing of the transported data would occur, would need to be very short to guaranty 1 ms. The relative 5G latency improvement over LTE would need to be (much) better than 10 (LTE pre-allocated) to 20 times (scheduled “normal” LTE), ignoring re-transmission (which would only make the challenge bigger.
An example. Say that 5G standardization folks gets the latency down to 0.5 ms (vs the ~ 20 – 10 ms today), the 5G processing node (i.e., Data Center) cannot be more than 50 km away from the 5G-radio cell (i..e, it takes light ca. 0.5 ms travel 100 km in fiber). This latency (budget) challenge has led the Telco industry to talk about the need for so-called edge computing and the need for edge data centers to provide the 5G promise of very low latencies. Remember this is opposing the past Telco trend of increasing centralization of computing & data processing resources. Moreover, it is bound to lead to incremental cost. Thus, show me the revenues.
There is no doubt that small, smaller and smallest 5G cells will be essential for providing the very lowest latencies and the smallness is coming for “free” given the very high frequencies planned for 5G. The cell environment of a small cell is more ideal than a macro-cellular harsh environment. Thus minimizing the likelihood of re-transmission events. And distances are shorter which helps as well.
I believe that converged telecommunications operators, are in a better position (particular compared to mobile only operations) to leverage existing fixed infrastructure for a 5G architecture relying on edge data centers to provide very low latencies. However, this will not come for free and without incremental costs.
End-2-End latency in the order of 20 ms are very important for a solid high quality VR user experience. However, to meet this kind of performance figure the VR content needs to be within the confines for the operator’s own network boundaries.
End-2-End (E2E) latencies of less than 100 ms would in general be perceived as instantaneous for normal internet consumption (e.g., social media, browsing, …). However that this still implies that operators will have to focus on developing internal to their network’s latencies far below the over-all 100 ms target and that due to externalities might try to get content inside their networks (and into their own data centers).
A 10-ms latency target, while much less moonshot, would be a far more economical target to strive for and might avoid substantial incremental cost of edge computing center deployments. It also resonates well with the 20 ms mentioned above, required for a great VR experience (leaving some computing and process overhead).
The 1-ms vision could be kept for use cases involving very short distances, highly ideal radio environment and with compute pretty much sitting on top of the whatever needs this performance, e.g., industrial plants, logistic / warehousing, …
Finally, the targeted extreme 5G speeds will require very substantial bandwidths. Such large bandwidths are readily available in the high frequency ranges (i.e., >3 GHz). The high frequency domain makes a lot of 5G technology challenges easier to cope with. Thus cell ranges will be (very) limited in comparison to macro cellular ones, e.g., Barclays Equity Research projects 10x times more cells will be required for 5G (10x!). 5G coverage will not match that of the macro cellular (LTE) network. In which case 5G will remain niche. With a lot less relevance to consumers. Obviously, 5G will have to jump the speed divide (a very substantial divide) to the macro cellular network to become relevant to the mass market. Little thinking appears to be spend on this challenge currently.
THE VERY FINE ART OF DETECTING MYTH & BALONEY.
Carl Sagan, in his great article The Fine Art of Baloney Detection, states that one should “Try not to get overly attached to a hypothesis just because it’s yours.”. Although Carl Sagan starts out discussing the nature of religious belief and the expectations of an afterlife, much of his “Baloney Detection Kit” applies equally well to science & technology. In particular towards our expert expectations towards consumerism and its most likely demand. After all, isn’t Technology in some respects our new modern day religion?
Some might have the impression that expectations towards 5G, is the equivalent of a belief in an afterlife or maybe more accurately resurrection of the Telco business model to its past glory. It is almost like a cosmic event, where after entropy death, the big bang gives birth to new, and supposedly unique (& exclusive) to our Telco industry, revenue streams that will make all alright (again). There clearly is some hype involved in current expectations towards 5G, although the term still has to enter the Gartner hype cycle report (maybe 2017 will be the year?).
The cynic (mea culpa) might say that it is in-evitable that there will be a 5G after 4G (that came after 3G (that came after 2G)). We also would expect 5G to be (a lot) better than 4G (that was better than 3G, etc..).
Well … Better for who? … Better for Telcos? Better for Suppliers? Better revenues? Their Shareholders? Better for our Consumers? Better for our Society? Better for (engineering) job security? … Better for Everyone and Everything? Wow! Right? … What does better mean?
Better speed … Yes! … Actually the 5G vision gives me insanely better speeds than LTE does today.
Better latency … Internal to the operator’s own network Yes! … Not per default noticeable for most consumer use cases relying on the externalities of the internet.
Better coverage … well if operators can afford to provide 100% 5G coverage then certainly Yes! Consumers would benefit even at a persistent 50 Mbps level.
Better availability …I don’t really think that Network Availability is a problem for the general consumer where there is coverage (at least not in mature markets, Myanmar absolutely … but that’s an infrastructure problem rather than a cellular standard one!) … Whether 100% availability is noticeable or not will depend a lot on the starting point.
Better (in the sense of more) revenues … Work in Progress!
Better margins … Only if incremental 5G cost to incremental 5G revenue is positive.
5G vision is flawed and not the huge advance in global connectivity as advertised.
The data rates promised by 5G will not be sufficiently valued by the users.
The envisioned 5G capacity demand will not be needed.
Most operators can simply not afford the cost required to realize 5G.
Technology advances are in-sufficient to realize the 5G vision.
Consistent connectivity is the more important aim of a 5G technology.
I recommend all to read William Webb’s well written and even better argued book. It is one for the first more official critiques of the 5G Vision. Some of the points certainly should have us pause and maybe even re-evaluate 5G priorities. If anything, it helps to sharpen 5G arguments.
Despite William Webb”s critique of 5G, one need to realize that a powerful technology vision of what 5G could be, even if very moonshot, does leapfrog innovation, needed to take a given technology too a substantially higher level, than what might otherwise be the case. If the 5G whitepaper by Rachid El Hattachi & Javan Erfanian had “just” been about better & consistent coverage, we would not have had the same technology progress independent of whether the ultimate 5G end game is completely reachable or not. Moreover, to be fair to the NGMN whitepaper, it is not that the whitepaper does not consider consistent connectivity, it very much does. It is more a matter of where lies the main attention of the industry at this moment. That attention is not on consistent connectivity but much more on niche use cases (i.e., ultra high bandwidth at ultra low latencies).
Another, very worthy 5G analysis, also from 2016, is the Barclays Equity Research “5G – A new Dawn” (September 2016) paper. The Barclays 5G analysis concludes ;
Mobile operator’s will need 10x more sites over the next 5 to 10 years driven by 5G demand.
There will be a strong demand for 5G high capacity service.
The upfront cost for 5G will be very substantial.
The cost of data capacity (i.e., Euro per GB) will fall approx. a factor 13 between LTE and 5G (note: this is “a bit” of a economic problem when capacity is supposed to increase a factor 50).
Sub-scale Telcos, including mobile-only operations, may not be able to afford 5G (note: this point, if true, should make the industry very alert towards regulatory actions).
Having a modernized super-scalable fixed broadband transport network likely to be a 5G King Maker (note: Its going to be great to be an incumbent again).
To the casual observer, it might appear that Barclays is in strong opposition to William Webb’s 5G view. However, maybe that is not completely so.
If it is true, that only very few Telco’s, primarily modernized incumbent fixed-mobile Telco’s, can afford to build 5G networks, one might argue that the 5G Vision is “somewhat” flawed economically. The root cause for this assumed economical flaw (according with Barclays, although they do not point out it is a flaw!) clearly is the very high 5G speeds, assumed to be demanded by the user. Resulting in massive increase in network densification and need for radically modernized & re-engineered transport networks to cope with this kind of demand.
Barclays assessments are fairly consistent with the illustration shown below of the likely technology cost impact, showing the challenges a 5G deployment might have;
Some of the possible operational cost improvements in IT, Platforms and Core shown in the above illustration arises from the natural evolving architectural simplifications and automation strategies expected to be in place by the time of the 5G launch. However, the expected huge increase in small cells are the root cause of most of the capital and operational cost pressures expected to arise with 5G. Depending on the original state of the telecommunications infrastructure (e.g., cloudification, virtualization,…), degree of transport modernization (e.g., fiberization), and business model (e.g., degree of digital transformation), the 5G economical impact can be relative modest (albeit momentarily painful) to brutal (i.e., little chance of financial return on investment). As discussed in the Barclays “5G – A new dawn” paper.
Furthermore, if the relative cost of delivering a 5G Byte is 13 – 14 times lower than an LTE Byte, and the 5G capacity demand is 50 times higher than LTE, the economics doesn’t work out very well. So if I can produce a 5G Byte at 1/14th of an LTE Byte, but my 5G Byte demand is 50x higher than in LTE, I could (simplistically) end up with more than 3x more absolute cost for 5G. That’s really Ugly! Although if Barclays are correct in the factor 10 higher number of 5G sites, then a (relevant) cost increase of factor 3 doesn’t seem completely unrealistic. Of course Barclays could be wrong! Unfortunately, an assessment of the incremental revenue potential has yet to be provided. If the price for a 5G Byte could be in excess of a factor 3 of an LTE Byte … all would be cool!
If there is something to be worried about, I would worry much more about the Barclays 5G analysis than the challenges of William Webb (although certainly somehow intertwined).
What is the 5G market potential in terms of connections?
Caution! Above global mobile connection forecast is likely to change many time as we approaches commercial launch and get much better impression of the 5G launch strategies of the various important players in the Telco Industry. In my own opinion, if 5G will be launched primarily in the mm-wave bands around and above 30 GHz, I would not expect to see a very aggressive 5G uptake. Possible a lot less than the above (with the danger of putting myself in the category of badly wrong forecasts of the future). If 5G would be deployed as an overlay to existing macro-cellular networks … hmmm who knows! maybe above would be a very pessimistic view of 5G uptake?
THE 5G PROMISES (WHAT OTHERS MIGHT CALL A VISION).
Let’s start with the 5G technology vision as being presented by NGMN and GSMA.
Note: ca. 5 minutes of service unavailability per year. If counted on active usage hours this would be less than 2.5 minutes per year per customer or less than 1/2 second per day per customer.
7.Perception of 100% coverage.
Note: In 2015 report from European Commission, “Broadband Coverage in Europe 2015”, for EU28, 86% of households had access to LTE overall. However, only 36% of EU28 rural households had access to LTE in 2015.
8.90% energy reduction of current network-related energy consumption.
Note: Approx. 1% of a European Mobile Operator’s total Opex.
9.Up-to 10 years battery life for low-power Internet of Things 5G devices.
The 5G whitepaper also discusses new business models and business opportunities for the Telco industry. However, there is little clarity on what would be the relevant 5G business targets. In other words, what would 5G as a technology bring, in additional Revenues, in Churn reduction, Capex & Opex (absolute) Efficiencies, etc…
More concrete and tangible economical requirements are badly required in the 5G discussion. Without it, is difficult to see how Technology can ensure that the 5G system that will be developed is also will be relevant for the business challenges in 2020 and beyond.
Today an average European Mobile operator spends approx. 40 Euro in Total Cost of Ownership (TCO) per customer per anno on network technology (and slightly less on average per connection). Assuming a capital annualization rate of 5 years and about 15% of its Opex relates to Technology (excluding personnel cost).
The 40 Euro TCO per customer per anno sustains today an average LTE EU28 customer experience of 31±9 Mbps downlink speed @ 41±9 ms (i.e., based on OpenSignal database with data as of 23 December 2016). Of course this also provides for 3G/HSPA network sustenance and what remains of the 2G network.
Thus, we might have a 5G TCO ceiling at least without additional revenue. The maximum 5G technology cost per average speed (in downlink) of 1 – 10 Gbps @ 10 ms should not be more than 40 Euro TCO per customer per anno (i.e, and preferably a lot less at the time we eventually will launch 5G in 2020).
Thus, our mantra when developing the 5G system should be:
5G should not add additional absolute cost burden to the Telecom P&L.
and also begs the question of proposing some economical requirements to partner up with the technology goals.
5G ECONOMIC REQUIREMENTS (TO BE CONSIDERED).
5G should provide new revenue opportunities in excess of 20% of access based revenue (e.g., Europe mobile access based revenue streams by 2021 expected to be in the order of 160±20 Billion Euro; thus the 5G target for Europe should be to add an opportunity of ca. 30±5 Billion in new non-access based revenues).
5G should not add to Technology TCO while delivering up-to 10 Gbps @ 10 ms (with a floor level of 1 Gbps) in urban areas.
5G focus on delivering macro-cellular customer experience at minimum 50 Mbps @ maximum 10 ms.
5G should target 20% reduction of Technology TCO while delivering up-to 10 Gbps @ 10 ms (min. 1 Gbps).
5G should keep pursuing better spectral efficiency (i.e., Mbps/MHz/cell) not only through means antennas designs, e.g., n-order MiMo and Massive-MiMo, that are largely independent of the air-interface (i.e., works as well with LTE).
Target at least 20% 5G device penetration within first 2 years of commercial launch (note: only after 20% penetration does the technology efficiency become noticeable).
In order not to increment the total technology TCO, we would at the very least need to avoid adding additional physical assets or infrastructure to the existing network infrastructure. Unless such addition provide a net removal of other physical assets and thus associated cost. This is in the current high frequency, and resulting demand for huge amount of small cells, going to be very challenging but would be less so by focusing more on macro cellular exploitation of 5G.
Thus, there need to be a goal to also overlay 5G on our existing macro-cellular network. Rather than primarily focus on small, smaller and smallest cells. Similar to what have been done for LT and was a much more challenge with UMTS (i.e., due to optimum cellular grid mismatch between the 2G voice-based and the 3G more data-centric higher frequency network).
What is the cost reference that should be kept in mind?
As shown below, the pre-5G technology cost is largely driven by access cost related to the number of deployed sites in a given network and the backhaul transmission.
Adding more sites, macro-cellular or a high number of small cells, will increase Opex and add not only a higher momentary Capex demand, but also burden future cash requirements. Unless equivalent cost can removed by the 5G addition.
Obviously, if adding additional physical assets leads to verifiable incremental margin, then accepting incremental technology cost might be perfectly okay (let”s avoid being radical financial controllers).
Though its always wise to remember;
Cost committed is a certainty, incremental revenue is not.
NAUGHTY … IMAGINE A 5G MACRO CELLULAR NETWORK (OHH JE!).
From the NGMN whitepaper, it is clear that 5G is supposed to be served everywhere (albeit at very different quality levels) and not only in dense urban areas. Given the economical constraints (considered very lightly in the NGMN whitepaper) it is obvious that 5G would be available across operators existing macro-cellular networks and thus also in the existing macro cellular spectrum regime. Not that this gets a lot of attention.
In the following, I am proposing a 5G macro cellular overlay network providing a 1 Gbps persistent connection enabled by massive MiMo antenna systems. This though experiment is somewhat at odds with the NGMN whitepaper where their 50 Mbps promise might be more appropriate. Due to the relative high frequency range in this example, massive MiMo might still be practical as a deployment option.
If you follow all the 5G news, particular on 5G trials in US and Europe, you easily could get the impression that mm-wave frequencies (e.g., 30 GHz up-to 300 GHz) are the new black.
There is the notion that;
“Extremely high frequencies means extremely fast 5G speeds”
which is baloney! It is the extremely large bandwidth, readily available in the extremely high frequency bands, that make for extremely fast 5G (and LTE of course) speeds.
We can have GHz bandwidths instead of MHz (i.e, 1,000x) to play with! … How extremely cool is that not? We totally can suck at fundamental spectral efficiency and still get out extremely high throughputs for the consumers data consumption.
While this mm-wave frequency range is very cool, from an engineering perspective and for sure academically as well, it is also extremely non-matching our existing macro-cellular infrastructure with its 700 to 2.6 GHz working frequency range. Most mobile networks in Europe have been build on a 900 or 1800 MHz fundamental grid, with fill in from UMTS 2100 MHz coverage and capacity requirements.
Being a bit of a party pooper, I asked whether it wouldn’t be cool (maybe not to the extreme … but still) to deploy 5G as an overlay on our existing (macro) cellular network? Would it not be economically more relevant to boost the customer experience across our macro-cellular networks, that actually serves our customers today? As opposed to augment the existing LTE network with ultra hot zones of extreme speeds and possible also an extreme number of small cells.
If 5G would remain an above 3 GHz technology, it would be largely irrelevant to the mass market and most use cases.
A 5G MACRO CELLULAR THOUGHT EXAMPLE.
So let’s be (a bit) naughty and assume we can free up 20MHz @ 1800 MHz. After all, mobile operators tend to have a lot of this particular spectrum anyway. They might also re-purpose 3G/LTE 2.1 GHz spectrum (possibly easier than 1800 MHz pending overall LTE demand).
In the following, I am ignoring that whatever benefits I get out of deploying higher-order MiMo or massive MiMo (mMiMo) antenna systems, will work (almost) equally well for LTE as it will for 5G (all other things being equal).
Remember we are after
A lot more speed. At least 1 Gbps sustainable user throughput (in the downlink).
Ultra-responsiveness with latencies from 10 ms and down (E2E).
No worse 5G coverage than with LTE (at same frequency).
Of course if you happen to be a NGMN whitepaper purist, you will now tell me that I my ambition should only be to provide sustainable 50 Mbps per user connection. It is nevertheless an interesting thought exercise to explore whether residential areas could be served, by the existing macro cellular network, with a much higher consistent throughput than 50 Mbps that might ultimately be covered by LTE rather than needing to go to 5G. Anywhere both Rachid El Hattachi and Jarvan Erfenian knew well enough to hedge their 5G speed vision against the reality of economics and statistical fluctuation.
and I really don’t care about the 1,000x (LTE) bandwidth per unit area promise!
Why? The 1,000x promise It is fairly trivial promise. To achieve it, I simply need a high enough frequency and a large enough bandwidth (and those two as pointed out goes nicely hand in hand). Take a 100 meter 5G-cell range versus a 1 km LTE-cell range. The 5G-cell is 100 times smaller in coverage area and with 10x more 5G spectral bandwidth than for LTE (e.g., 200 MHz 5G vs 20 MHz LTE), I would have the factor 1,000 in throughput bandwidth per unit area. This without having to assume mMiMo that I could also choose to use for LTE with pretty much same effect.
Detour to the cool world of Academia: University of Bristol published recently (March 2016) a 5G spectral efficiency of ca. 80 Mbps/MHz in a 20 MHz channel. This is about 12 times higher than state of art LTE spectral efficiency. Their base station antenna system was based on so-called massive MiMo (mMiMo) with 128 antenna elements, supporting 12 users in the cell as approx. 1.6 Gbps (i.e., 20 MHz x 80 Mbps/MHz). The proof of concept system operated 3.5 GHz and in TDD mode (note: mMiMo does not scale as well for FDD and pose in general more challenges in terms of spectral efficiency). National Instruments provides a very nice overview of 5G MMiMo systems in their whitepaper “5G Massive MiMo Testbed: From Theory to Reality”.
A picture of the antenna system is shown below;
Figure above: One of the World’s First Real-Time massive MIMO Testbeds–Created at Lund University. Source: “5G Massive MiMo (mMiMo) Testbed: From Theory to Reality” (June 2016).
For a good read and background on advanced MiMo antenna systems I recommend Chockalingam & Sundar Rajan’s book on “Large MiMo Systems” (Cambridge University Press, 2014). Though there are many excellent accounts of simple MiMo, higher-order MiMo, massive MiMo, Multi-user MiMo antenna systems and the fundamentals thereof.
Back to naughty (i.e., my 5G macro cellular network);
So let’s just assume that the above mMiMO system, for our 5G macro-cellular network,
and keeping in mind that FDD mMiMo performance tends to be lower than TDD all else being equal.
will, in due time, be available for 5G with a channel of at least 20 MHz @ 1800MHz. And at a form factor that can be integrated well with existing macro cellular design without incremental TCO.
This is a very (VERY!) big assumption. Requirements of substantially more antenna space for massive MiMo systems, at normal cellular frequency ranges, are likely to result. Structural integrity of site designs would have to be checked and possibly be re-enforced to allow for the advanced antenna system, contributing to both additional capital cost and possible incremental tower/site lease.
So we have (in theory) a 5G macro-cellular overlay network with at least cell speeds of 1+Gbps, which is ca. 10 – 20 times that of today’s LTE networks cell performance (not utilizing massive MiMo!). If I have more 5G spectrum available, the performance would increase linearly (and a bit) accordingly.
mMiMo designed for TDD, but works at some performance penalty for FDD.
mMiMo will really be deployable at low total cost of ownership (i.e., it is not enough that the antenna system itself is low cost!).
mMiMo performance leap frog comes at the price of high computational complexity (e.g., should be factored into the deployment cost).
mMiMo relies on distributed processing algorithms which at this scale is relative un-exploited territory (i.e., should be factored into the deployment cost).
But wait a minute! I might (naively) theorize away additional operational cost of the active electronics and antenna systems on the 5G cell site (overlaid on legacy already present!). I might further assume that the Capex of the 5G radio & antenna system can be financed within the regular modernization budget (assuming such a budget exists). But … But surely our access and core transport networks have not been scaled for a factor 10 – 20 (and possibly a lot more than that) in crease in throughput per active customer?
No it has not! Really Not!
Though some modernized converged Telcos might be a lot better positioned for thefixed broadband transformation required to sustain the 5G speed promise.
For most mobile operators, it is highly likely that substantial re-design and investments of transport networks will have to be made in order to support the 5G target performance increase above and beyond LTE.
Definitely a lot more on this topic in a subsequent Blog.
ON THE 5G PROMISES.
Lets briefly examine the 8 above 5G promises or visionary statements and how these impact the underlying economics. As this is an introductory chapter, the deeper dive and analysis will be referred to subsequent chapters.
NEED FOR SPEED.
PROMISE 1: From 1 to 10 Gbps in actual experienced 5G speed per connected device (at a max. of 10 ms round-trip time).
PROMISE 2: Minimum of 50 Mbps per user connection everywhere (at a max. of 10 ms round-trip time).
PROMISE 3: Thousand times more bandwidth per unit area (compared to LTE).
Before anything else, it would be appropriate to ask a couple of questions;
“Do I need this speed?” (The expert answer if you are living inside the Telecom bubble is obvious! Yes Yes Yes ….Customer will not know they need it until they have it! …).
“that kind of sustainable speed for what?” (Telekom bubble answer would be! Lots of useful things! … much better video experience, 4K, 8K, 32K –> fully emerged holographic VR experience … Lots!)
“am I willing to pay extra for this vast improvement in my experience?” (Telekom bubble answer would be … ahem … that’s really a business model question and lets just have marketing deal with that later).
What is true however is:
My objective measurable 5G customer experience, assuming the speed-coverage-reliability promise is delivered, will quantum leap to un-imaginable levels (in terms of objectively measured performance increase).
Maybe more importantly, will the 5G customer experience from the very high speed and very low latency really be noticeable to the customer? (i.e, the subjective or perceived customer experience dimension).
Let’s ponder on this!
In Europe end of 2016, the urban LTE speed and latency user experience per connection would of course depend on which network the customer would be (not all being equal);
In 2016 on average in Europe an urban LTE user, experienced a DL speed of 31±9 Mbps, UL speed of 9±2 Mbps and latency around 41±9 milliseconds. Keep in mind that OpenSignal is likely to be closer to the real user’s smartphone OTT experience, as it pings a server external to the MNOs network. It should also be noted that although the OpenSignal measure might be closer to the real customer experience, it still does not provide the full experience from for example page load or video stream initialization and start.
The 31 Mbps urban LTE user experience throughput provides for a very good video streaming experience at 1080p (e.g., full high definition video) even on a large TV screen. Even a 4K video stream (15 – 32 Mbps) might work well, provided the connection stability is good and that you have the screen to appreciate the higher resolution (i.e., a lot bigger than your 5” iPhone 7 Plus). You are unlikely to see the slightest difference on your mobile device between the 1080p (9 Mbps) and 480p (1.0 – 2.3 Mbps) unless you are healthy young and/or with a high visual acuity which is usually reserved for the healthy & young.
With 5G, the DL speed is targeted to be at least 1 Gbps and could be as high as 10 Gbps, all delivered within a round trip delay of maximum 10 milliseconds.
5G target by launch (in 2020) is to deliver at least 30+ times more real experienced bandwidth (in the DL) compared to what an average LTE user would experience in Europe 2016. The end-2-end round trip delay, or responsiveness, of 5G is aimed to be at least 4 times better than the average experienced responsiveness of LTE in 2016. The actual experience gain between LTE and 3G has been between 5 – 10 times in DL speed, approx. 3 –5 times in UL and between 2 to 3 times in latency (i.e., pinging the same server exterior to the mobile network operator).
According with Sandvine’s 2015 report on “Global Internet Phenomena Report for APAC & Europe”, in Europe approx. 46% of the downstream fixedpeak aggregate traffic comes from real-time entertainment services (e.g., video & audio streamed or buffered content such as Netflix, YouTube and IPTV in general). The same report also identifies that for Mobile (in Europe) approx. 36% of the mobile peak aggregate traffic comes from real-time entertainment. It is likely that the real share of real-time entertainment is higher, as video content embedded in social media might not be counted in the category but rather in Social Media. Particular for mobile, this would bring up the share with between 10% to 15% (more in line with what is actually measured inside mobile networks). Real-time entertainment and real-time services in general is the single most important and impacting traffic category for both fixed and mobile networks.
Video viewing experience … more throughput is maybe not better, more could be useless.
Video consumption is a very important component of real-time entertainment. It amounts to more than 90% of the bandwidth consumption in the category. The Table below provides an overview of video formats, number of pixels, and their network throughput requirements. The tabulated screen size is what is required (at a reasonable viewing distance) to detect the benefit of a given video format in comparison with the previous. So in order to really appreciate 4K UHD (ultra high definition) over 1080p FHD (full high definition), you would as a rule of thumb need double the screen size (note there are also other ways to improved the perceived viewing experience). Also for comparison, the Table below includes data for mobile devices, which obviously have a higher screen resolution in terms of pixels per inch (PPI) or dots per inch (DPI). Apart from 4K (~8 MP) and to some extend 8K (~33 MP), the 16K (~132 MP) and 32K (~528 MP) are still very yet exotic standards with limited mass market appeal (at least as of now).
We should keep in mind that there are limits to the human vision with the young and healthy having a substantial better visual acuity than what can be regarded as normal 20/20 vision. Most magazines are printed at 300 DPI and most modern smartphone displays seek to design for 300 DPI (or PPI) or more. Even Steve Jobs has addressed this topic;
However, it is fair to point out that this assumed human vision limitation is debatable (and have been debated a lot). There is little consensus on this, maybe with the exception that the ultimate limit (at a distance of 4 inch or 10 cm) is 876 DPI or approx. 300 DPI (at 11.5 inch / 30 cm).
Anyway, what really matters is the customers experience and what they perceive while using their device (e.g., smartphone, tablet, laptop, TV, etc…).
So lets do the visual acuity math for smartphone like displays;
We see (from the above chart) that for an iPhone 6/7 Plus (5.5” display) any viewing distance above approx. 50 cm, a normal eye (i.e., 20/20 vision) would become insensitive to video formats better than 480p (1 – 2.3 Mbps). In my case, my typical viewing distance is ca. 30+ cm and I might get some benefits from 720p (2.3 – 4.5 Mbps) as opposed to 480p. Sadly my sight is worse than the norm of 20/20 (i.e., old! and let’s just leave it at that!) and thus I remain insensitive to the resolution improvements 720p would provide. If you have a device with at or below 4” display (e.g., iPhone 5 & 4) the viewing distance where normal eyes become insensitive is ca. 30+ cm.
All in all, it would appear that unless cellular user equipment, and the way these are being used, changes very fundamentally the 480p to 720p range might be more than sufficient.
If this is true, it also implies that a cellular 5G user on a reliable good network connection would need no more than 4 – 5 Mbps to get an optimum viewing (and streaming) experience (i.e., 720p resolution).
The 5 Mbps streaming speed, for optimal viewing experience, is very far away from our 5G 1-Gbps promise (x200 times less)!
Assuming instead of streaming we want to download movies, assuming we lots of memory available on our device … hmmm … then a typical 480p movie could be download in ca. 10 – 20 seconds at 1Gbps, a 720p movie between 30 and 40 seconds, and a 1080p would take 40 to 50 seconds (and likely a waste due to limitations to your vision).
However with a 5G promise of super reliable ubiquitous coverage, I really should not need to download and store content locally on storage that might be pretty limited.
Downloads to cellular devices or home storage media appears somewhat archaic. But would benefit from the promised 5G speeds.
I could share my 5G-Gbps with other users in my surrounding. A typical Western European household in 2020 (i.e., about the time when 5G will launch) would have 2.17 inhabitants (2.45 in Central Eastern Europe), watching individual / different real-time content would require multiples of the bandwidth of the optimum video resolution. I could have multiple video streams running in parallel, to likely the many display devices that will be present in the consumer’s home, etc… Still even at fairly high video streaming codecs, a consumer would be far away from consuming the 1-Gbps (imagine if it was 10 Gbps!).
Okay … so video consumption, independent of mobile or fixed devices, does not seem to warrant anywhere near the 1 – 10 Gbps per connection.
Surely EU Commission wants it!
EU Member States have their specific broadband coverage objectives – namely: ‘Universal Broadband Coverage with speeds at least 30 Mbps by 2020’ (i.e, will be met by LTE!) and ‘Broadband Coverage of 50% of households with speeds at least 100 Mbps by 2020 (also likely to be met with LTE and fixed broadband means’.
The European Commission’s “Broadband Coverage in Europe 2015” reports that 49.2% of EU28 Households (HH) have access to 100 Mbps (i.e., 50.8% of all HH have access to less than 100 Mbps) or more and 68.2% to broadband speeds above 30 Mbps (i.e., 32.8% of all HH with access to less than 30 Mbps). No more than 20.9% of HH within EU28 have FTTP (e.g., DE 6.6%, UK UK 1.4%, FR 15.5%, DK 57%).
The EU28 average is pretty good and in line with the target. However, on an individual member state level, there are big differences. Also within each of the EU member states great geographic variation is observed in broadband coverage.
Interesting, the 5G promises to per user connection speed (1 – 10 Gbps), coverage (user perceived 100%) and reliability (user perceived 100%) is far more ambitious that the broadband coverage objectives of the EU member states.
So maybe indeed we could make the EU Commission and Member States happy with the 5G Throughput promise. (this point should not be underestimated).
Web browsing experience … more throughput and all will be okay myth!
So … Surely, the Gbps speeds can help provide a much faster web browsing / surfing experience than what is experienced today for LTE and for the fixed broadband? (if there ever was a real Myth!).
In other words the higher the bandwidth, the better the user’s web surfing experience should become.
While bandwidth (of course) is a factor in customers browsing experience, it is but a factor out of several that also governs the customers real & perceived internet experience; e.g., DNS Lookups (this can really mess up user experience), TCP, SSL/TLS negotiation, HTTP(S) requests, VPN, RTT/Latency, etc…
An excellent account of these various effects is given by Jim Getty’s “Traditional AQM is not enough” (i.e., AQM: Active Queue Management). Measurements (see Jim Getty’s blog) strongly indicates that at a given relative modest bandwidth (>6+ Mbps) there is no longer any noticeable difference in page load time. In my opinion there are a lot of low hanging fruits in network optimization that provides large relative improvements in customer experience than network speed alone..
Thus one might carefully conclude that, above a given throughput threshold it is unlikely that more throughput would have a significant effect on the consumers browsing experience.
More work needs to be done in order to better understand the experience threshold after which more connection bandwidth has diminishing returns on the customer’s browsing experience. However, it would appear that 1-Gbps 5G connection speed would be far above that threshold. An average web page in 2016 was 2.2 MB which from an LTE speed perspective would take 568 ms to load fully provided connection speed was the only limitation (which is not the case). For 5G the same page would download within 18 ms assuming that connection speed was the only limitation.
Downloading content (e.g., FTTP).
Now we surely are talking. If I wanted to download the whole Library of the US Congress (I like digital books!), I am surely in need for speed!?
The US Congress have estimated that the whole print collection (i.e., 26 million books) adds up to 208 terabytes.Thus assuming I have 208+ TB of storage, I could within 20+ (at 1 Gbps) to 2+ (at 20 Gbps) days download the complete library of the US Congress.
In fact, at 1 Gbps would allow me to download 15+ books per second (assuming 1 book is on average 3oo pages and formatted at 600 DPI TIFF which is equivalent to ca. 8 Mega Byte).
So clearly, for massive file sharing (music, videos, games, books, documents, etc…), the 5G speed promise is pretty cool.
Though, it does assume that consumers would continue to see a value in storing information locally on their personally devices or storage medias. The idea remains archaic, but I guess there will always be renaissance folks around.
What about 50 Mbps everywhere (at a 10 ms latency level)?
Firstly, providing a customers with a maximum latency of 10 ms with LTE is extremely challenging. It would be highly unlikely to be achieved within existing LTE networks, particular if transmission retrials are considered. From OpenSignal December 2016 measurements shown in the chart below, for urban areas across Europe, the LTE latency is on average around 41±9 milliseconds. Considering the LTE latency variation we are still 3 – 4 times away from the 5G promise. The country average would be higher than this. Clearly this is one of the reasons why the NGMN whitepaper proposes a new air-interface. As well as some heavy optimization and redesigns in general across our Telco networks.
The urban LTE persistent experience level is very reasonable but remains lower than the 5G promise of 50 Mbps, as can be seen from the chart below;
The LTE challenge however is not the customer experience level in urban areas but on average across a given geography or country. Here LTE performs substantially worse (also on throughput) than what the NGMN whitepaper’s ambition is. Let us have a look at the current LTE experience level in terms of LTE coverage and in terms of (average) speed.
Based on European Commission “Broadband Coverage in Europe 2015” we observe that on average the total LTE household coverage is pretty good on an EU28 level. However, the rural households are in general underserved with LTE. Many of the EU28 countries still lack LTE consistent coverage in rural areas. As lower frequencies (e.g., 700 – 900 MHz) becomes available and can be overlaid on the existing rural networks, often based on 900 MHz grid, LTE rural coverage can be improved greatly. This economically should be synchronized with the normal modernization cycles. However, with the current state of LTE (and rural network deployments) it might be challenging to reach a persistent level of 50 Mbps per connection everywhere. Furthermore, the maximum 10 millisecond latency target is highly unlikely to be feasible with LTE.
In my opinion, 5G would be important in order to uplift the persistent throughput experience to at least 50 Mbps everywhere (including cell edge). A target that would be very challenging to reach with LTE in the network topologies deployed in most countries (i.e., particular outside urban/dense urban areas).
The customer experience value to the general consumer of a maximum 10 millisecond latency is in my opinion difficult to assess. At a 20 ms response time would most experiences appear instantaneous. The LTE performance of ca. 40 ms E2E external server response time, should satisfy most customer experience use case requirements beside maybe VR/AR.
Nevertheless, if the 10 ms 5G latency target can be designed into the 5G standard without negative economical consequences then that might be very fine as well.
Another aspect that should be considered is the additional 5G market potential of providing a persistent 50 Mbps service (at a good enough & low variance latency). Approximately 70% of EU28 households have at least a 30 Mbps broadband speed coverage. If we look at EU28 households with at least 50 Mbps that drops to around 55% household coverage. With the 100% (perceived)coverage & reliability target of 5G as well as 50 Mbps everywhere, one might ponder the 30% to 45% potential of households that are likely underserved in term of reliable good quality broadband. Pending the economics, 5G might be able to deliver good enough service at a substantial lower cost compared more fixed centric means.
Finally, following our expose on video streaming quality, clearly a 50 Mbps persistent 5G connectivity would be more than sufficient to deliver a good viewing experience. Latency would be less of an issue in the viewing experience as longs as the variation in the latency can be kept reasonable low.
I greatly acknowledge my wife Eva Varadi for her support, patience and understanding during the creative process of creating this Blog.
The perception of value is orders of magnitude higher than the willingness to pay, i.e.,
“I would NOT give up Internet for life for a Million+ US Dollars … oh … BUT… I don’t want to pay more than a couple of bucks for it either” (actually for a mature postpaid-rich market the chances are that over your expected life-time you will pay between 30 to 40 thousand US$ for mobile internet & voice & some messaging).
Price plans are fascinating! … Particular the recent data-centric price plans bundling in legacy services such as voice and SMS.
Needles to say that a consumer today often needs an advanced degree in science to really understand the price plans they are being presented. A high degree of trust is involved in choosing a given plan. The consumer usually takes what has been recommended by the shop expert (who most likely doesn’t have an advanced science degree either). This shop expert furthermore might (or might not) get a commission (i.e., a bonus) selling you a particular plan and thus in such a case hardly is the poster child of objectiveness.
How does the pricing experts come to the prices that they offer to the consumer? Are those plans internally consistent … or maybe not?
It becomes particular interesting to study data-centric price plans that try to re-balance Mobile Voice and SMS.
How is 4G (i.e., in Europe also called LTE) being charged versus “normal” data offerings in the market? Do the mobile consumer pay more for Quality? Or maybe less?
What is the real price of mobile data? … Clearly, it is not the price we pay for a data-centric price plan.
A Data-centric Tale of a Country called United & a Telecom Company called Anything Anywhere!
As an example of mobile data pricing and in particular of data-centric mobile pricing with Voice and SMS included, I looked at a Western European Market (let’s call it United) and a mobile operator called Anything Anywhere. Anything Anywhere (AA) is known for its comprehensive & leading-edge 4G network as well as several innovative product ideas around mobile broadband data.
In my chosen Western European country United, voice revenues have rapidly declined over the last 5 years. Between 2009 to 2014 mobile voice revenues lost more than 36% compared to an overall revenue loss of “only” 14%. This corresponds to a compounded annual growth rate of minus 6.3% over the period. For an in depth analysis of the incredible mobile voice revenue losses the mobile industry have incurred in recent years see my blog “The unbearable lightness of mobile voice”.
Did this market experience a massive uptake in prepaid customers? No! Not at all … The prepaid share of the customer base went from ca. 60% in 2009 to ca. 45% in 2014. So in other words the Postpaid base over the period had grown with 15% and in 2014 was around 55%. This should usually have been a cause for great joy and incredible boost in revenues. United is also a market that has largely managed not to capitalize economically on substantial market consolidation.
As it is with many other mobile markets, engaging & embracing the mobile broadband data journey has been followed by a sharp decline in the overall share of voice revenue from ca. 70% in 2009 to ca. 50% in 2014. An ugly trend when the total mobile revenue declines as well.
The Smartphone penetration in United as of Q1 2014 was ca. 71% with 32% iOS-based devices. Compare this to 2009 where the smartphone penetration was ca. 21% with iOS making out around 75+%.
Our Mobile Operator AA has the following price plan structure (note: all information is taken directly from AA’s web site and can be found back if you guess which company it applies to);
Data-centric price plans with unlimited Voice and SMS.
Differentiated speed plans, i.e., 4G (average speed advertised to 12 – 15 Mbps) vs. Double Speed 4G (average speed advertised to 24 – 30 Mbps).
Offer plans that apply Europe Union-wide.
Option to pay less for handsets upfront but more per month (i.e., particular attractive for expensive handsets such as iPhone or Samsung Galaxy top-range models).
Default offering is 24 month although a shorter period is possible as well.
Offer SIM-only data-centric with unlimited voice & SMS.
Offer Data-only SIM-only plans.
Further you will get access to extensive “WiFi Underground”. Are allowed tethering and VoIP including Voice-calling over WiFi.
So here is an example of AA’s data-centric pricing for various data allowances. In this illustration I have chosen to add an iPhone 6 Plus (why? well I do love that phone as it largely replaces my iPad outside my home!) with 128GB storage. This choice have no impact on the fixed and variable parts of the respective price plans. For SIM-Only plans in the data below, I have added the (Apple) retail price of the iPhone 6 Plus (light grey bars). This is to make the comparison somewhat more comparable. It should of course be clear that in the SIM-only plans, the consumer is not obliged to buy a new device.
Figure above: illustrates the total consumer cost or total price paid over the period (in local currency) of different data plans for our leading Western European Mobile Operator AA. The first 9 plans shown above includes a iPhone 6 Plus with 128GB memory. The last 5 are SIM only plans with the last 2 being Data-only SIM-only plans. The abbreviations are the following PPM: Pay per Month (but little upfront for terminal), PUF: Pay UpFront (for terminal) and less per month, SIMO: SIM-Only plan, SIMDO: SIM Data-Only plan, xxGB: The xx amount of Giga Bytes offered in Plan, 2x indicates double 4G speed of “normal” and 1x indicates “normal” speed, 1st UL indicates unlimited voice in plan, 2nd UL indicates unlimited SMS in plan, EU indicates that the plan also applies to countries in EU without extra charges. So PPM20GB2xULULEU defines a Pay per Month plan (i.e., the handset is pay over the contract period and thus leads to higher monthly charges) with 20 GB allowance at Double (4G) Speed with Unlimited Voice and Unlimited SMS valid across EU. In this plan you would pay 100 (in local currency) for a iPhone 6 Plus with 128 GB. Note the local Apple Shop retail price of an iPhone 6 Plus with 128 GB is around 789 in local currency (of which ca. 132 is VAT) for this particular country. Note: for the SIM-only plans (i.e., SIMO & SIMDO) I have added the Apple retail price of a iPhone 6 Plus 128GB. It furthermore should be pointed out that the fixed service fee and the data consumption price does not vary with choice of handset.
If I decide that I really want that iPhone 6 Plus and I do not want to pay the high price (even with discounts) that some price plans offers. AA offers me a 20GB 4G data-plan, pay 100 upfront for the iPhone 6 Plus (with 128 GB memory) and for the next 24 month 63.99 (i.e., as this feels much cheaper than paying 64) per month. After 24 month my total cost of the 20 GB would be 1,636. I could thus save 230 over the 24 month if I wanted to pay 470 (+370 compared to previous plan & – 319 compared to Apple retail price) for the iPhone. In this lower cost plan my monthly cost of the 20 GB would be 38.99 or 25 (40%!) less on a monthly basis.
The Analysis show that a “Pay-less-upfront-and-more-per-month” subscriber would end up after the 24 month having paid at least ca. 761 for the iPhone 6 Plus (with 128GB). We will see later, that the total price paid for the iPhone 6 Plus however is likely to be approximately 792 or slightly above today’s retail price (based on Apple’s pricing).
The Price of a Byte and all that Jazz
So how does the above data-price plans look like in terms of Price-per-Giga-Byte?
Although in most cases not be very clear to the consumer, the data-centric price plan is structured around the price of the primary data allowance (i.e., the variable part) and non-data related bundled services included in the plan (i.e., the fixed service part representing non-data items).
There will be a variable price reflecting the data-centric price-plans data allowance and a “Fixed” Service Fee that capture the price of bundled services such as voice and SMS. Based on total price of the data-centric price plan, it will often appear that the higher the allowance the cheaper does your unit-data “consumption” (or allowance) become. Indicating that volume discounts have been factored into the price-plan. In other words, the higher the data allowance the lower the price per GB allowance.
This is often flawed logic and simply an artefact of the bundled non-data related services being priced into the plan. However, to get to that level of understanding requires a bit of analysis that most of us certainly don’t do before a purchase.
Figure above: Illustrates the unit-price of a Giga Byte (GB) versus AA’s various data-centric price plans. Note the price plans can be decomposed into a variable data-usage attributable price (per GB) and a fixed service fee that accounts for non-data services blended into the price. The Data Consumption per GB is the variable data-usage dependable part of the Price Plan and the Total price per GB is the full price normalized to the plans data consumption allowance.
So with the above we have argued that the total data-centric price can be written as a fixed and a variable part;
As will be described in more detail below, the data-centric price is structured in what can be characterized as a “Fixed Service Fee” and a variable “Data Consumption Price” that depends on a given price-plan’s data allowance (i.e., GB is Giga Byte). The “Data Consumption Price” is variable in nature and while it might be a complex (i.e. in terms of complexity) function of data allowance it typically be of the form with the exponent (i.e., Beta) being 1 or close to 1. In other words the Data Consumptive price is a linear (or approximately so) function of the data allowance. In case is larger than 1, data pricing gets progressively more expensive with increasing allowance (i.e., penalizing high consumption or as I believe right-costing high consumption). For lower than 1, data gets progressively cheaper with increasing data allowances corresponding to volume discounts with the danger of mismatching the data pricing with the cost of delivering the data.
The “Fixed Service Fee” depends on all the non-data related goodies that are added to the data-centric price plan, such as (a) unlimited voice, (b) unlimited SMS, (c) Price plan applies Europe-wide (i.e., EU-Option), (d) handset subsidy recovery fee, (e) maybe a customer management fee, etc..
For most price data-centric plan, If the data-centric price divided by the allowance would be plotted against the allowance in a Log-Log format would result in a fairly straight-line.
Nothing really surprising given the pricing math involved! It is instructive to see what actually happens when we take a data-centric price and divide by the corresponding data allowance;
For very large data allowances the price-centric per GB would asymptotically converge to , i.e., the unit cost of a GB. As is usually a lot smaller than , we see that there is another limit, where the allowance is relative low, where we would see the data-centric pricing per GB slope (in a Log-Log plot) become linear in the data allowance. Typically for allowances from 0.1 GB up towards 50 GB, non-linear slope of approximately -0.7±0.1 is observed and thus in between the linear and the constant pricing regime.
We can also observe that If the total price, of a data-centric price plan associated with a given data allowance (i.e., GB), is used to derive a price-per-GB, one would conclude that most mobile operators provide the consumer with volume discounts as they adapt higher data allowance plans. The GB gets progressively cheaper for higher usage plans. As most data-centric price plans are in the range where is (a lot) smaller than , it will appear that the unit price of data declines as the data allowance increases. However in most cases it is likely an artefact of the Fixed Service Fee that reflects non-data related services which unless a data-only bundle can be a very substantial part of the data-centric price plan.
It is clear that data-allowance normalizing the totality of a data-centric price plan, particular when non-data services have been blended into the plan, will not reveal the real price of data. If used for assessing, for example, data profitability or other mobile data related financial KPIs this approach might be of very little use.
Figure above: illustrates the basic characteristics of a data-centric price plan normalized by the data allowance. The data for this example reflects the AA’s data-centric price plans 2x4G Speed with bundled unlimited Voice & SMS as well as applying EU-wide. We see that the Beta value corresponds to a Volume Discount (at values lower than 1) or a Volume Penalty (at values higher than 1).
Oh yeah! … The really “funny” part of most data-price plan analysis (including my own past ones!) are they are more likely to reflect the Fixed Service Part (independent of the Data allowance) of the Data-centric price plan than the actual unit price of mobile data.
What to expect from AA’s data-centric price plans?
so in a rational world of data-centric pricing (assuming such exist) what should we expect of Anything Anywhere’s price plans as advertised online;
The (embedded) price for unlimited voice would be the same irrespective of the data plan’s allowed data usage (i.e., unlimited Voice does not depend on data plan).
The (embedded) price for unlimited SMS would be the same irrespective of the data plan’s allowed data usage (i.e., unlimited SMS does not depend on data plan).
You would pay more for having your plan extended to apply across Europe Union compared to not having this option.
You would (actually you should) expect to pay more per Mega Byte for the Double Speed option as compared to the Single Speed Option.
If you decide to “finance” your handset purchase (i.e., pay less upfront option) within a data plan you should expect to pay more on a monthly basis.
Given a data plan has a whole range of associated handsets priced From Free (i.e., included in plan without extra upfront charge) to high-end high-priced Smartphones, such as iPhone 6 Plus 128 GB, you would not expect that handset related cost would have been priced into the data plan. Or if it is, it must be the lowest common denominator for the whole range of offered handsets at a given price plan.
Where the discussion becomes really interesting is how your data consumption should be priced; (1) You pay more per unit of data consumption as you consume more data on a monthly basis, (2) You pay the same per unit irrespective of your consumption or (3) You should have a volume discount making your units cheaper the more you consume.
of course the above is if and only if the price plans have been developed in reasonable self-consistent manner.
Figure above: Illustrates AA’s various data-centric price plans (taken from their web site). Note that PPM represents low upfront (terminal) cost for the consumer and higher monthly cost and PUF represent paying upfront for the handset and thus having lower monthly costs as a consequence. The Operator AA allows the consumer in the PPM Plan to choose for an iPhone 6 Plus 128GB (priced at 100 to 160) or an IPhone 6 Plus 64GB option (at a lower price of course).
First note that Price Plans (with more than 2 data points) tend to be linear with the Data Usage allowance.
The Fixed Service Fee – The Art of Re-Capture Lost legacy Value?
In the following I define the Fixed Service Fee as the part of the total data-centric price plan that is independent of a given plan’s data allowance. The logic is that this part would contain all non-data related cost such as Unlimited Voice, Unlimited SMS, EU-Option, etc..
From AA’s voice plan (for 250 Minutes @ 10 per Month & 750 Minutes @ 15 per Month) with unlimited SMS (& no data) it can be inferred that
Price of Unlimited SMS can be no higher than 7.5. This however is likely also include general customer maintenance cost.
Monthly customer maintenance cost (cost of billing, storage, customer care & systems support, etc.) might be deduced from the SIM-Only Data-Only package and would be
Price of Monthly Customer Maintenance could be in the order of 5, which would imply that the Unlimited SMS price would be 2.5. Note the market average Postpaid SMS ARPU in 2014 was ca., 8.40 (based on Pyramid Research data). The market average number of postpaid SMS per month was ca. 273 SMS.
From AA’s SIM-only plan we get that the fixed portion of providing service (i.e., customer maintenance, unlimited Voice & SMS usage) is 14 and thus
Price of Unlimited Voice should be approximately 6.5. Note the market average Postpaid Voice ARPU was ca. 12 (based on Pyramid Research data). The market average voice usage per month was ca. 337 minutes. Further from the available limited voice price plans it can be deduced that unlimited voice must be higher than 1,000 Minutes or more than 3 times the national postpaid average.
The fixed part of the data-centric pricing difference between the data-centric SIM-only plan and similar data-centric plan including a handset (i.e., all services are the same except for the addition of the handset) could be regarded as a minimum handset financing cost allowing the operator to recover some of the handset subsidy
Equipment subsidy recovery cost of 7 (i.e., over a 24 month period this amounts to 168 which is likely to recover the average handset subsidy). Note is the customer chooses to pay little upfront for the handset, the customer would have to pay 26 extra per month in he fixed service fee. Thus low upfront cost result in another 624 over the 24 month contract period. Interestingly is that with the initial 7 for handset subsidy recovery in the basic fixed service fee a customer would have paid 792 in handset recovery over 24 month period the contract applies to (a bit more than the iPhone 6 Plus 128GB retail price).
The price for allowing the data-centric price-plan to apply Europe Union Wide is
The EU-Option (i.e., plan applicable within EU) appears to be priced at ca. 5 (caution: 2x4G vis-a-vis 1x4G could have been priced into this delta as well).
For EU-option price it should be noted here that the two plans that are being compared differs not only in the EU-option. The plan without the EU option is a data plan with “normal” 4G speed, while the EU-option plan supports double 4G speeds. So in theory the additional EU-option charge of 5 could also include a surcharge for the additional speed.
Why an operator would add the double speed to the fixed Service Fee price part is “bit” strange. The 2x4G speed price-plan option clearly is a variable trigger for cost (and value to the customer’s data usage). Thus should be introduced in the the variable part (i.e., the Giga-Byte dependent part) of the data-centric price plan.
It is assumed that indeed the derived difference can be attributed to the EU-option, i.e., the double speed has not been include in the monthly Fixed Service Fee.
In summary we get AA’s data-centric price plan’s monthly Fixed Service Fee de-composition as follows;
Figure above: shows the composition of the monthly fixed service fee as part of AA’s data-centric plans. Of course in a SIM-only scenario the consumer would not have the Handset Recovery Fee inserted in the price plan.
So irrespective of the data allowance a (postpaid) customer would pay between 26 to 52 per month depending on whether handset financing is chosen (i.e., Low upfront payment on the expense of higher monthly cost).
Mobile data usage still has to happen!
The price of Mobile Data Allowance.
The variable data-price in the studied date-centric price plans are summarized in the table below as well as the figure;
Price per GB
Pay Less Upfront More per Month
Pay Upfront & Less per Month
SIM-Only Data Only
2 (only 2 data points)
The first thing that obviously should make you Stop in Wonder is that Single 4G Speed Giga Byte is more than Twice the price of a Double 4G Speed Giga Byte … In need for speed … well that will give you a pretty good deal with AA’s price 2x4G plans.
Second thing to notice is that it would appear to be a really bad deal (with respect to the price-per-byte) to be a SIM-Only Data-Only customer.
The Data-Only pays 2 per GB. Almost 3 times more than if you would choose a subscription with a device, double speed, double unlimited and EU-wide applicable price plan.
Agreed! In absolute terms the SIM-only Data-only cost a lot less per month (9 less than the 20GB pay device upfront) and it is possible to run away after 12 months (versus the 24 month plans). One rationale for charging extra per Byte for a SIM-only Data-only plan could be that the SIM card might be used in Tablet or Data-card/Dongle products that typically does consume most if not all of a given plans allowance. For normal devices and high allowance plans on average the consumption can be quiet a lot lower than the actual allowance. Particular over a 24 month period.
You might argue that this is all about how the data-centric price plans have been de-composed in a fixed service fee (supposedly the non-data dependent component) and a data consumptive price. However, even when considering the full price of a given price plan is the Single-4G-Speed more expensive per Byte than Double-4G-Speed.
You may also argue that I am comparing apples and oranges (or even bananas pending taste) as the Double-4G-Speed plans include a devices and a price-plan that applies EU-wide versus the SIM-only plan that includes the customers own device and a price-plan that only works in United. All true of course … Why that should be more expensive to opt out of is a bit beyond me and why this should have an inflationary impact on the price-per-Byte … well a bit of a mystery as well.
At least there is no (statistical) difference in the variable price of a Giga Byte whether the customer chooses to pay of her device over the 24 month contract period or pay (most of) it upfront.
For AA it doesn’t seem to be of concern! …. As 88% would come back for more (according with their web site).
Obviously this whole analysis above make the big assumption that the data-centric price plans are somewhat rationally derived … this might not be the case!
and it assumes that rationally & transparently derived price plans are the best for the consumer …
and it assumes what is good for the consumer is also good for the company …
Is AA different in this respect to that of other Operators around the world …
No! AA is not different from any other incumbent operator coming from a mobile voice centric domain!
I greatly acknowledge my wife Eva Varadi for her support, patience and understanding during the creative process of creating this Blog.
Postscript – The way I like to look at (rational … what ever that means) data-centric pricing.
Firstly, it would appear that AA’s pricing philosophy follows the industry standard of pricing mobile services and in particular mobile data-centric services by the data volume allowance. Non-data services are added to the data-centric price plan and in all effect make up for the most part of the price-plan even at relative higher data allowances;
Figure above: illustrates the typical approach to price plan design in the Telecom’s industry. Note while not per se wrong it often overweight’s the volume element of pricing and often results in sub-optimizing the Quality and Product aspects . Source: Dr. Kim K Larsen’s Mind Share contribution at Informa’s LTE World Summit May 2012; “Right pricing LTE and mobile broadband in general (a Technologist’ Observations)”.
Unlimited Voice and SMS in AA’s standard data-centric plans clearly should mitigate possible loss or migration away from old fashion voice (i.e., circuit switched) and SMS. However both the estimated allowances for unlimited voice (6.5) and SMS (2.5) appear to be a lot lower than their classical standalone ARPUs for the postpaid category. This certainly could explain that this market (as many others in Western Europe) have lost massive amount of voice revenues over the last 5 years. In other words re-capturing or re-balancing legacy service revenues into data-centric plans still have some way to go in order to be truly effective (if at all possible which is highly questionable at this time and age).
As a Technologist, I am particular interested in how the technology cost and benefits are being considered in data-centric price plans.
The big challenge for the pricing expert who focus too much on volume is that the same volume can result from vastly different network qualities and speed. The customers handset will drive the experience of quality and certainly consumption. By that differences in network load and thus technology cost. A customer with a iPhone 6 Plus is likely to load the mobile data network more (and thus incur higher cost) than a customer with a normal screen smartphone of 1 or 2 generations removed from iPhone 6 Plus. It is even conceivable that a user with iPhone 6 Plus will load the network more than a customer with a normal iPhone 6 (independent of the iOS). This is very very different for Voice and SMS volumetric considerations in legacy price plans, where handset had little (or no) impact on network load relative to the usage.
For data-centric price plans to be consistent with the technology cost incurred one should consider;
Higher “guarantied” Quality, typically speed or latency, should be priced higher per Byte than lower quality plans (or at the very least not lower).
Higher Volumetric Allowances should be priced per Byte higher than Lower Volumetric Allowance (or at the very least not lower).
Offering unlimited Voice & SMS in data-centric plans (as well as other bundled goodies) should be carefully re-balanced to re-capture some of lost legacy revenues.
That AA’s data-centric plans for double speed appears to be cheaper than their plans at a lower data delivery quality level is not consistent with costing. Of course, AA cannot really guaranty that the customer will get double 4G speed everywhere and as such it may not be fair to charge substantially more than for single speed. However, this is of course not what appear to happen here.
AA’s lowest data unit price (in per Giga Byte) is around 0.6 – 0.7 (or 0.06 – 0.07 Cent per Mega Byte). That price is very low and in all likelihood lower than their actual production cost of a GB or MB.
However, one may argue that as long as the Total Service Revenue gained by a data-centric price plan recover the production cost, as well as providing a healthy margin then whether the applied data unit-price is designed to recover the data production cost is maybe less of an issue.
In other words, data profitability may not matter as much as overall profitability. This said it remains in my opinion in-excusable for a mobile operator not to understand its main (data) cost drivers and ensure it is recovered in their overall pricing strategies.
Surely! You may say? … “Surely Mobile Operators know their cost structure and respective cost drivers and their price plans reflects this knowledge?”
It is my observation that most price plans (data-centric or not) are developed primarily in response to competition (which of course is an important pricing element as well) rather than firmly anchored in Cost, Value & Profit considerations. Do Operators really & deeply know their own cost structure and cost drivers? … Ahhh … In my opinion few really appear to do!